FORD WRS-M1H1238-A1-2013 FABRIC STAMPEDE PATTERN FLAT WOVEN 33% PIR PCR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WRS-M1H1238-A1-2013 FABRIC STAMPEDE PATTERN FLAT WOVEN 33% PIR PCR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M1H1238-A1-2013 FABRIC STAMPEDE PATTERN FLAT WOVEN 33% PIR PCR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 00 2013 05 10 Released M. Dumitrescu, NA Controlled document at www.MATS Copyright 2013, Ford Global Technologies, Inc. Page 1 of 2 FABRIC, STAMPEDE PATTERN, FLAT WOVEN WRS-M1H1238-A1 33% PIR/PCR UNLAMINATED 1. SCOPE The material defined

2、by this specification is a woven jacquard face fabric. The fabric is made with 33% PIR/PCR (Post industrial/post-consumer) recycled yarn. . 2. APPLICATION This specification was released originally for material used as an interior trim fabric for F-150 2016 seat bolster. The fabric was approved as b

3、ackcoated. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). Materials with recycled content as defined by WRS-M99P42-A2 (Textile Materials, Identifica

4、tion of Recycled Content) should be used whenever technically feasible. 3.1.1 This specification must contain 33% recycled content as defined by WRS-M99P42-A2. The remaining portion of the material can come from virgin sources 3.1.2 In addition to the requirements listed herein, the fabric shall mee

5、t all requirements WSS-M8P18-A1/A2/A3/A4 as applicable. 3.2 FABRIC CONSTRUCTION 3.2.1 Fabric Count, +/- 10% tolerance (ASTM D 3775) Warp 307 ends/10 cm Weft 171 picks/10 cm 3.2.2 Fabric Weight, +/-10 % tolerance (FLTM BN 106-01) Face fabric 300 g/m2 Back coat 41 g/m2 Total weight 341 g/m2 3.3 COMPOS

6、ITION (ASTM D 629) Tolerance as specified in WSS-M8P18-A1/A4 ENGINEERING MATERIAL SPECIFICATION WRS-M1H1238-A1 Copyright 2013, Ford Global Technologies, Inc. Page 2 of 2 Fabric 100% Polyester Backcoating Acrylic 3.4 YARN CONSTRUCTION (ASTM D 1244) Warp 167 dtex (100% recycled textured polyester yarn

7、) x 3 Weft 167 dtex (textured polyester yarn) x 3 167 dtex (textured polyester yarn) x 3 3.5 METHOD OF DYEING Solution dye Or as approved by Materials Engineering 3.6 FINISHING OPERATIONS wash,dry, tenter, backcoated, Or as approved by Materials Engineering 4. GENERAL INFORMATION The information giv

8、en below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. 5. SUMMARY OF REVISIONS