EN ISO 11296-1-2011 en Plastics piping systems for renovation of underground nonpressure drainage and sewerage networks - Part 1 General《地下无压排水道及污水网的翻修用塑料管道系统 第1部分 综述》.pdf

《EN ISO 11296-1-2011 en Plastics piping systems for renovation of underground nonpressure drainage and sewerage networks - Part 1 General《地下无压排水道及污水网的翻修用塑料管道系统 第1部分 综述》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 11296-1-2011 en Plastics piping systems for renovation of underground nonpressure drainage and sewerage networks - Part 1 General《地下无压排水道及污水网的翻修用塑料管道系统 第1部分 综述》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11296-1:2011Plastics piping systems forrenovation of undergroundnon-pressure drainage andsewerage networksPart 1: General (ISO 11296-1:2009)BS EN ISO 11296-1:2011 BRITI

2、SH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 11296-1:2011. It is identical to ISO 11296-1:2009. It supersedes BS EN 13566-1:2002, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e P R I / 8 8 / 3 ,

3、R e h a b i l i t a t i o n o f p i p e l i n e s y s t e m s using plastics piping materials and components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. User

4、s are responsible for its correct application. BSI 2011 ISBN 978 0 580 72265 3 ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Com

5、mittee on 31 May 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11296-1 April 2011 ICS 23.040.20; 23.040.45; 93.030; 91.140.80 Supersedes EN 13566-1:2002English Version Plastics piping systems for renovation of underground

6、 non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009) Systmes de canalisations en plastique pour la rnovation des rseaux dassainissement enterrs sans pression - Partie 1: Gnralits (ISO 11296-1:2009) Kunststoff-Rohrleitungssysteme fr die Renovierung von erdverlegten druckl

7、osen Entwsserungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009) This European Standard was approved by CEN on 8 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

8、 a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German)

9、. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, C

10、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION

11、 COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11296-1:2011: EBS EN ISO 11296-1:2011 EN ISO 11296-1:2011

12、(E) 3 Foreword The text of ISO 11296-1:2009 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 11296-1:2011 by Technical Committee CEN/TC 1

13、55 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be

14、withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13566-1:2002. Acc

15、ording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, I

16、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 11296-1:2009 has been approved by CEN as a EN ISO 11296-1:2011 without any modification. BS EN ISO 112

17、96-1:2011ISO 11296-1:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword .v Introductionvi 1 Scope1 2 Normative references1 3 Terms and definitions .1 3.1 General terms 1 3.2 Techniques.3 3.3 Characteristics.4 3.4 Origin of materials.5 3.5 Product stages.6 4 Symbols and abbreviated terms

18、6 4.1 Symbols6 4.2 Abbreviated terms .6 5 Pipes at the “M” stage 7 5.1 Materials .7 5.2 General characteristics.7 5.3 Material characteristics.7 5.4 Geometric characteristics 7 5.5 Mechanical characteristics.7 5.6 Physical characteristics7 5.7 Jointing.7 5.8 Marking.7 6 Fittings at the “M” stage.8 6

19、.1 Materials .8 6.2 General characteristics.8 6.3 Material characteristics.8 6.4 Geometric characteristics 8 6.5 Mechanical characteristics.8 6.6 Physical characteristics8 6.7 Jointing.8 6.8 Marking.8 7 Ancillary components.9 8 Fitness for purpose of the installed lining system at the “I” stage .9 8

20、.1 Materials .9 8.2 General characteristics.9 8.3 Material characteristics.9 8.4 Geometric characteristics 9 8.5 Mechanical characteristics.10 8.6 Physical characteristics10 8.7 Additional characteristics.10 8.8 Sampling.10 9 Installation practice.10 9.1 Preparatory work .10 9.2 Storage, handling an

21、d transport of pipe and fittings 10 9.3 Equipment 10 9.4 Installation11 9.5 Process-related inspection and testing 12 BS EN ISO 11296-1:2011ISO 11296-1:2009(E) iv ISO 2009 All rights reserved9.6 Lining termination12 9.7 Reconnection to existing manholes and laterals .12 9.8 Final inspection and test

22、ing .12 9.9 Documentation.12 Bibliography 13 BS EN ISO 11296-1:2011ISO 11296-1:2009(E) ISO 2009 All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stand

23、ards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta

24、ke part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees i

25、s to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibili

26、ty that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11296-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids. ISO 11296 c

27、onsists of the following parts, under the general title Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks: Part 1: General Part 3: Lining with close-fit pipes Part 4: Lining with cured-in-place pipes Lining with continuous pipes is to form the subject

28、of a part 2, lining with discrete pipes is to form the subject of a part 5 and lining with spirally-wound pipes is to form the subject of a part 7. BS EN ISO 11296-1:2011ISO 11296-1:2009(E) vi ISO 2009 All rights reservedIntroduction The System Standard, of which this is part 1, specifies the requir

29、ements for plastics piping systems of various materials used for the renovation of existing pipelines in a specified application area. System Standards for renovation specify procedures for the following applications: plastics piping systems for renovation of underground non-pressure drainage and se

30、werage networks; plastics piping systems for renovation of underground drainage and sewerage networks under pressure; plastics piping systems for renovation of underground water supply networks; plastics piping systems for renovation of underground gas supply networks. These System Standards are dis

31、tinguished from those for conventionally installed plastics piping systems because they set requirements for certain characteristics in the as-installed condition, after site processing. This is in addition to specifying requirements for system components, as manufactured. Each of the System Standar

32、ds comprises a part 1 (general) and all applicable renovation technique family-related parts from the following: part 2: lining with continuous pipes; part 3: lining with close-fit pipes; part 4: lining with cured-in-place pipes; part 5: lining with discrete pipes; part 7: lining with spirally-wound

33、 pipes. The requirements for any given renovation technique family are given in part 1, applied in conjunction with the other relevant part. For example, parts 1 and 2 specify the requirements relating to lining with continuous pipes. For complementary information, see ISO 11295. Not all technique f

34、amilies are applicable to every area of application and this is reflected in the part numbers included in each System Standard. A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons across renovation technique families. Figure 1 gives the common st

35、ructure and the relationship between ISO 11296 and the System Standards for other application areas. BS EN ISO 11296-1:2011ISO 11296-1:2009(E) ISO 2009 All rights reserved viiFigure 1 Format of the renovation System Standards BS EN ISO 11296-1:2011BS EN ISO 11296-1:2011INTERNATIONAL STANDARD ISO 112

36、96-1:2009(E) ISO 2009 All rights reserved 1Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General 1 Scope This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation o

37、f underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar1). It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existin

38、g pipeline or any annular filler. This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques (see 3.1.2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edi

39、tion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1610:1997, Construction and testing of drains and sewers EN 13508-2, Conditions of drain and sewer systems outside buildings Part 2: Visual inspection coding system 3 Term

40、s and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General terms 3.1.1 pipeline system interconnecting pipe network for the conveyance of fluids 3.1.2 rehabilitation all measures for restoring or upgrading the performance of an existing pipeline syste

41、m 1) 1 bar = 0,1 MPa = 0,1 N/mm2= 105N/m2. BS EN ISO 11296-1:2011ISO 11296-1:2009(E) 2 ISO 2009 All rights reserved3.1.3 renovation work incorporating all or part of the original fabric of the pipeline by means of which its performance is improved 3.1.4 replacement rehabilitation of an existing pipe

42、line system by the installation of a new pipeline system, without incorporating the original fabric 3.1.5 maintenance keeping an existing pipeline system operational without the installation of additional fabric 3.1.6 repair rectification of local damage 3.1.7 lining pipe pipe inserted for renovatio

43、n purposes 3.1.8 liner lining pipe after installation 3.1.9 lining system lining pipe and all relevant fittings for insertion into an existing pipeline for the purposes of renovation 3.1.10 renovated pipeline system existing pipeline system plus the installed lining system used to renovate it, along

44、 with any grout or other annular filling material used 3.1.11 characteristic property, dimension or other feature of a material or component 3.1.12 declared value limiting value of a characteristic declared in advance by the lining system supplier, which becomes the requirement for the purposes of a

45、ssessment of conformity 3.1.13 annular filler material for grouting annular space between existing pipeline and the lining system 3.1.14 grouting process of filling voids around the lining system 3.1.15 simulated installation installation of a lining system into a simulated host pipeline, using repr

46、esentative equipment and processes, in order to provide samples for testing which are representative of an actual installation BS EN ISO 11296-1:2011ISO 11296-1:2009(E) ISO 2009 All rights reserved 33.1.16 simulated host pipeline section of pipeline, which is not part of an operational network, but

47、which replicates the environment of an operational network 3.1.17 technique family group of renovation techniques which are considered to have common characteristics for standardization purposes 3.2 Techniques The various techniques for renovation of underground non-pressure drainage and sewerage ne

48、tworks, within the scope of pipeline rehabilitation techniques generally, are shown schematically in Figure 2. For definitions of standardized renovation techniques given in Figure 2, but outside the scope of this part of ISO 11296, see ISO 11295. This part of ISO 11296 is applicable to the followin

49、g technique families. 3.2.1 lining with continuous pipes lining with pipe made continuous prior to insertion, and which has not been shaped to give it a cross-sectional diameter smaller than its final diameter after installation 3.2.2 lining with close-fit pipes lining with a continuous pipe for which the cross-section is reduced to facilitate installation and reverted after installation to provide a close fit to the existing pipe NOTE There are two options for achieving the reduction in cross-section: a) reduct