EN 62386-210-2011 en Digital addressable lighting interface - Part 210 Particular requirements for control gear - Sequencer (device type 9)《数字可寻址照明接口 第210部分 控制装置的特殊要求 序列发生器(装置类型9)》.pdf

《EN 62386-210-2011 en Digital addressable lighting interface - Part 210 Particular requirements for control gear - Sequencer (device type 9)《数字可寻址照明接口 第210部分 控制装置的特殊要求 序列发生器(装置类型9)》.pdf》由会员分享，可在线阅读，更多相关《EN 62386-210-2011 en Digital addressable lighting interface - Part 210 Particular requirements for control gear - Sequencer (device type 9)《数字可寻址照明接口 第210部分 控制装置的特殊要求 序列发生器(装置类型9)》.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDigital addressable lighting interfacePart 210: Particular requirements for control gear Sequencer (device Type 9)BS EN 62386-210:2011National forewordThis British Standard is th

2、e UK implementation of EN 62386-210:2011. It isidentical to IEC 62386-210:2011.The UK participation in its preparation was entrusted by Technical CommitteeCPL/34, Lamps and Related Equipment, to Subcommittee CPL/34/3, Auxiliariesfor lamps.A list of organizations represented on this committee can be

3、obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2011ISBN 978 0 580 62958 7ICS 29.140.50; 29.140.99Compliance with a British Standard cannot confer immunity fromlegal obl

4、igations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 July 2011.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 62386-210:2011EUROPEAN STANDARD EN 62386-210 NORME EUROPENNE EUROPISCHE NORM June 2011 CE

5、NELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldw

6、ide for CENELEC members. Ref. No. EN 62386-210:2011 E ICS 29.140.50; 29.140.99 English version Digital addressable lighting interface - Part 210: Particular requirements for control gear - Sequencer (device type 9) (IEC 62386-210:2011) Interface dclairage adressable numrique - Partie 210: Exigences

7、particulires pour les appareillages de commande - Squenceur (dispositifs de type 9) (CEI 62386-210:2011) Digital adressierbare Schnittstelle fr die Beleuchtung - Teil 210: Besondere Anforderungen an Betriebsgerte - Sequenzer (Gertetyp 9) (IEC 62386-210:2011) This European Standard was approved by CE

8、NELEC on 2011-05-25. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand

9、ards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and noti

10、fied to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

11、 Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 62386-210:2011EN 62386-210:2011 - 2 - Foreword The text of document 34C/915/CDV, future edition 1 of IEC 62386-210, prepared by SC 34C, Auxi

12、liaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62386-210 on 2011-05-25. EN 62386-210 is intended to be used in conjunction with EN 62386-101 and EN 62386-102, which contain general requirements for the re

13、levant product type (control gear or control devices). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: la

14、test date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-02-25 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-05-25 Annex ZA has been added by CENELEC. _ Endors

15、ement notice The text of the International Standard IEC 62386-210:2011 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60598-1 NOTE Harmonized as EN 60598-1. IEC

16、60669-2-1 IEC 60921 IEC 60923 IEC 60925 IEC 60929 IEC 61347-1 IEC 61347-2-3 IEC 61547 CISPR 15 NOTE Harmonized as EN 60669-2-1. NOTE Harmonized as EN 60921. NOTE Harmonized as EN 60923. NOTE Harmonized as EN 60925. NOTE Harmonized as EN 60929. NOTE Harmonized as EN 61347-1. NOTE Harmonized as EN 613

17、47-2-3. NOTE Harmonized as EN 61547. NOTE Harmonized as EN 55015. _ BS EN 62386-210:2011- 3 - EN 62386-210:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the applicat

18、ion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/

19、HD applies. Publication Year Title EN/HD Year IEC 62386-101 2009 Digital addressable lighting interface - Part 101: General requirements - System EN 62386-101 2009 IEC 62386-102 2009 Digital addressable lighting interface - Part 102: General requirements - Control gearEN 62386-102 2009 BS EN 62386-2

20、10:2011 4 62386-210 IEC:2011 CONTENTS INTRODUCTION . 7 1 Scope . 8 2 Normative references . 8 3 Terms and definitions . 8 4 General description 9 5 Electrical specifications 9 6 Interface power supply . 9 7 Transmission protocol structure 9 8 Timing 9 9 Method of operation . 9 10 Declaration of vari

21、ables 14 11 Definition of commands 15 12 Test procedures . 24 Bibliography 62 Figure 1 Timing example for an automatic sequence 13 Figure 2 Application extended configuration command sequence example . 16 Figure 3 Test sequence “Physical address allocation“ 24 Figure 4 Test sequence “QUERY FEATURES“

22、 . 25 Figure 5 Test sequence “Configure POINT N“ 26 Figure 6 Test sequence “Configuration sent twice“ 27 Figure 7 Test sequence “Configuration time-out“ . 28 Figure 8 Test sequence “Configuration command in-between 1“ . 29 Figure 9 Test sequence “Configuration command in-between 2“ . 30 Figure 10 Te

23、st sequence “COPY TO POINT N“ 31 Figure 11 Test sequence “COPY TO POINT N sent twice“ 32 Figure 12 Test sequence “COPY TO POINT N time-out“ . 33 Figure 13 Test sequence “COPY TO POINT N command in-between“ . 34 Figure 14 Test sequence “CHANNEL SELECTION“ . 35 Figure 15 Test sequence “CHANNEL SELECTI

24、ON sent twice / time-out“ 36 Figure 16 Test sequence “CHANNEL SELECTION command in-between“ 37 Figure 17 Test sequence “CONFIGURE CONTROL N“ 38 Figure 18 Test sequence “CONFIGURE CONTROL N sent twice / time-out“ . 39 Figure 19 Test sequence “CONFIGURE CONTROL N command in-between“ 40 Figure 20 Test

25、sequence “ENABLE DEVICE TYPE: Application extended commands“ . 41 Figure 21 Test sequence ENABLE DEVICE TYPE: Application extended configuration commands 1 . 42 Figure 22 Test sequence ENABLE DEVICE TYPE: Application extended configuration commands 2 . 43 Figure 23 Subsequence Configure sequence 44

26、Figure 24 Test sequence GO TO POINT N . 45 BS EN 62386-210:201162386-210 IEC:2011 5 Figure 25 Test sequence GO TO NEXT POINT 46 Figure 26 Test sequence GO TO PREVIOUS POINT 47 Figure 27 Test sequence Automatic sequence 48 Figure 28 Timing diagram for test Automatic sequence . 49 Figure 29 Test seque

27、nce Automatic sequence pointer . 50 Figure 30 Test sequence Automatic sequence number of runs 51 Figure 31 Test sequence Automatic sequence stopped by command . 52 Figure 32 Test sequence Sequencer performance 53 Figure 33 Template for Sequencer performance . 53 Figure 34 Test sequence START AT POIN

28、T N number of runs 54 Figure 35 Test sequence RESET SEQUENCER . 55 Figure 36 Test sequence RESET SEQUENCER send twice / time-out . 56 Figure 37 Test sequence RESET SEQUENCER command in-between 57 Figure 38 Test sequence RESET CONTROL N . 58 Figure 39 Test sequence FAULTY CHANNEL . 59 Figure 40 Test

29、sequence QUERY EXTENDED VERSION NUMBER . 60 Figure 41 Test sequence RESERVED APPLICATION EXTENDED COMMANDS 61 Table 1 Access to the sequencer variables 11 Table 2 Sequencer programming example . 12 Table 3 Declaration of variables . 14 Table 4 Summary of the application extended command set 23 Table

30、 5 Parameters for test sequence “Configure POINT N“ 26 Table 6 Parameters for test sequence “Configuration sent twice“ 27 Table 7 Parameters for test sequence “Configuration time-out“ . 28 Table 8 Parameters for test sequence “Configuration command in-between 1“ . 29 Table 9 Parameters for test sequ

31、ence “Configuration command in-between 2“ . 30 Table 10 Parameters for test sequence “COPY TO POINT N“ 31 Table 11 Parameters for test sequence “COPY TO POINT N sent twice“ 32 Table 12 Parameters for test sequence “COPY TO POINT N time-out“ . 33 Table 13 Parameters for test sequence “COPY TO POINT N

32、 command in-between“ . 34 Table 16 Parameters for test sequence “CHANNEL SELECTION command in-between“. 37 Table 19 Parameters for test sequence “CONFIGURE CONTROL N command in-between“. 40 Table 20 Parameters for test sequence “ENABLE DEVICE TYPE: Application extended commands“ 41 Table 21 Paramete

33、rs for test sequence ENABLE DEVICE TYPE: Application extended configuration commands 1 42 Table 23 Parameters for subsequence Configure sequence . 44 Table 24 Parameters for test sequence GO TO POINT N . 45 Table 27 Parameters for test sequence Automatic sequence 48 Table 29 Parameters for test sequ

34、ence Automatic sequence pointer . 50 Table 30 Parameters for test sequence Automatic sequence number of runs . 51 BS EN 62386-210:2011 6 62386-210 IEC:2011 Table 31 Parameters for test sequence Automatic sequence stopped by command . 52 Table 34 Parameters for test sequence START AT POINT N number o

35、f runs 54 Table 37 Parameters for test sequence RESET SEQUENCER command in-between . 57 Table 39 Parameters for test sequence FAULTY CHANNEL . 59 Table 41 Parameters for test sequence RESERVED APPLICATION EXTENDED COMMANDS 61 BS EN 62386-210:201162386-210 IEC:2011 7 INTRODUCTION This first edition o

36、f IEC 62386-210 is published in conjunction with IEC 62386-101 and IEC 62386-102. The division of IEC 62386 into separately published parts provides for ease of future amendments and revisions. Additional requirements will be added as and when a need for them is recognised. This International Standa

37、rd, and the other parts that make up the IEC 62386-200 series, in referring to any of the clauses of IEC 62386-101 or IEC 62386-102, specifies the extent to which such a clause is applicable and the order in which the tests are to be performed. The parts also include additional requirements, as nece

38、ssary. All parts that make up the IEC 62386-200 series are self-contained and therefore do not include references to each other. Where the requirements of any of the clauses of IEC 62386-101 or IEC 62386-102 are referred to in this International Standard by the sentence “The requirements of IEC 6238

39、6-1XX, clause n apply”, this sentence is to be interpreted as meaning that all requirements of the clause in question of Part 101 or Part 102 apply, except any which are inapplicable to the specific type of lamp control gear covered by Part 210. All numbers used in this International Standard are de

40、cimal numbers unless otherwise noted. Hexadecimal numbers are given in the format 0xVV, where VV is the value. Binary numbers are given in the format XXXXXXXXb or in the format XXXX XXXX, where X is 0 or 1; x in binary numbers means dont care. BS EN 62386-210:2011 8 62386-210 IEC:2011 DIGITAL ADDRES

41、SABLE LIGHTING INTERFACE Part 210: Particular requirements for control gear Sequencer (device type 9) 1 Scope This International Standard specifies a protocol and test procedures for the control by digital signals of electronic control gear working as automatic sequencers. 2 Normative references The

42、 following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 62386-101:2009, Digital addressable lighting int

43、erface Part 101: General requirements System IEC 62386-102:2009, Digital addressable lighting interface Part 102: General requirements Control gear 3 Terms and definitions For the purposes of this document, the terms and definitions given in Clause 3 of IEC 62386-101:2009 and Clause 3 of IEC 62386-1

44、02:2009 apply, with the following additional definitions. 3.1 multi channel device device which provides more than one output for controlling light sources NOTE The individual outputs can have different states at the same time. 3.2 point tuple consisting of a sequencer fade time, a hold time and an

45、arc power level for each output channel NOTE A point is reached when the sequencer fade time of this point has expired. 3.3 next point point following the current point in a sequence 3.4 previous point point preceding the current point in a sequence 3.5 pointer contents of a register used as referen

46、ce to the starting point of a sequence BS EN 62386-210:201162386-210 IEC:2011 9 NOTE For this purpose, a register may be one of the scenes 0 to 15 or the POWER ON LEVEL or the SYSTEM FAILURE LEVEL. 4 General description The requirements of Clause 4 of IEC 62386-101:2009 and Clause 4 of IEC 62386-102

47、:2009 shall apply. 5 Electrical specifications The requirements of Clause 5 of IEC 62386-101:2009 and Clause 5 of IEC 62386-102:2009 shall apply. 6 Interface power supply The requirements of Clause 6 of IEC 62386-101:2009 and Clause 6 of IEC 62386-102:2009 shall apply, if a power supply is integrate

48、d with the gear. 7 Transmission protocol structure The requirements of Clause 7 of IEC 62386-101:2009 and Clause 7 of IEC 62386-102:2009 shall apply. 8 Timing The requirements of Clause 8 of IEC 62386-101:2009 and Clause 8 of IEC 62386-102:2009 shall apply. 9 Method of operation The requirements of Clause 9 of IEC 62386-101:2009 and Clause 9 of IEC 62386-102:2009 shall apply with the following exceptions: Amendments to Clause 9 of IEC 62386-102:2009: Replacement: 9.2 Power-on Control gear shall start to react