DLA MIL-DTL-70329 1 A-2009 NUT PLAIN ROUND BALL AND ROLLER BEARINGS NARROW SERIES METRIC.pdf

《DLA MIL-DTL-70329 1 A-2009 NUT PLAIN ROUND BALL AND ROLLER BEARINGS NARROW SERIES METRIC.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-70329 1 A-2009 NUT PLAIN ROUND BALL AND ROLLER BEARINGS NARROW SERIES METRIC.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 4 FSC 5310 MIL-DTL-70329/1A 7 JANUARY 2009 SUPERSEDING DOD-N-70329/1 16 August 1982 MILITARY SPECIFICATION SHEET NUT, PLAIN, ROUND, BALL AND ROLLER BEARINGS NARROW SERIES, METRIC This specification is approved for use by all Departments and Agencies of the Department of Defense. The co

2、mplete requirements for aquiring the product described herein shall consist of this specification sheet and MIL-DTL-70329. FE PITCH GDTTHREADRADIUS ORCHAMFER ATBOTTOM OFSLOTS30 245 - 60BOTH SIDESTOL VZXTOL S MY MX4 SLOTS EQUALLY SPACEDZ Y CNOTES: 1. All dimensions are in millimeters. FIGURE 1. Confi

3、guration. METRIC Inactive for new design after 1 October 1999 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-70329/1A 2REQUIREMENTS: 1. Part number. The part number consists of the letter “D” followed by the basic number of this specificatio

4、n sheet, a code letter indicating material and finish, and a dash number taken from table I. EXAMPLE: D70329/1 - A 010 Dash number from table I designating nominal size in mm. -N- Carbon steel, unplated -A- Carbon steel, zinc coated -P- CRES -B- Alloy steel, phosphate coated Specification sheet numb

5、er 2. Configuration. See figure 1. 3. Subject term (key word) listing. Carbon steel, unplated Carbon steel, zinc coated CRES Alloy steel, phosphate coated 4. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issu

6、e were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and rela

7、tionship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-70329/1A 3TABLE I. Dash numbers and dimensions. Dash T-thread C D E F G S V No. 5H Outside dia Tol Thick- ness Tol Face Dia Tol Slot depth Tol Slot depth Tol

8、 Tol Tol 010 M10X0.75 18 0 -.11 4 13.5 0 -.27 2 3 +.25 0 012 M12X1 22 4 0 17 2 3 015 M15X1 25 0 5 -.18 21 2 4 017 M17X1 28 -.13 5 24 0 2 4 020 M20X1 32 6 26 -.33 2 0 4 022 M22X1 34 6 28 2 -.5 4 .5 .04 025 M25X1.5 38 0 7 32 2 5 028 M28X1.5 42 -.16 7 36 2 5 +.30 030 M30X1.5 45 7 0 38 0 2 5 0 032 M32X1

9、.5 48 8 -.22 40 -.39 2 5 035 M35X1.5 52 8 44 2 5 040 M40X1.5 58 0 9 50 2.5 6 045 M45X1.5 65 -.19 10 56 2.5 +.9 6 050 M50X1.5 70 11 61 0 2.5 0 6 055 M55X2 75 11 67 -.46 3 7 060 M60X2 80 11 73 3 7 065 M65X2 85 12 79 3 7 070 M70X2 92 12 85 3.5 8 075 M75X2 98 0 13 90 3.5 8 +.36 .75 080 M80X2 105 -.22 15

10、 0 95 0 3.5 8 0 085 M85X2 110 16 -.27 102 -.54 3.5 8 .05 090 M90X2 120 16 108 4 10 095 M95X2 125 17 113 4 10 100 M100X2 130 18 120 4 10 105 M105X2 140 18 126 5 +1.2 12 110 M110X2 145 19 133 5 0 12 115 M115X2 150 0 19 137 5 12 120 M120X2 155 -.25 20 138 0 5 12 125 M125X2 160 21 148 -.63 5 12 130 M130

11、X2 165 21 149 5 12 135 M135X2 175 22 0 160 6 14 140 M140X2 180 22 -.33 160 6 14 +.43 1.0 145 M145X2 190 24 171 6 14 0 150 M150X2 195 24 171 6 14 155 M155X3 200 0 25 182 7 16 .06 160 M160X3 210 -.29 25 182 7 16 165 M165X3 210 26 193 7 +1.5 16 170 M170X3 220 26 193 0 7 0 16 180 M180X3 230 27 203 -.72

12、8 18 190 M190X3 240 28 214 8 18 200 M200X3 250 29 226 8 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-70329/1A 4Custodians: Preparing Activity: Army - AT DLA- IS Navy - OS Air Force - 99 (Project 5310-2007-005) Review Activities: Army -C

13、R4, Navy - MC, SH NSA - NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-