ASTM F2048-2000 Standard Practice for Reporting Slip Resistance Test Results《防滑试验结果报告的标准实施规范》.pdf

《ASTM F2048-2000 Standard Practice for Reporting Slip Resistance Test Results《防滑试验结果报告的标准实施规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2048-2000 Standard Practice for Reporting Slip Resistance Test Results《防滑试验结果报告的标准实施规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2048 00An American National StandardStandard Practice forReporting Slip Resistance Test Results1This standard is issued under the fixed designation F 2048; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides a framework for reporting theresults of slip resistance tests.1.2 ApplicationThis practice is

3、intended for use as asuggested format for recording and reporting data obtainedduring slip resistance testing. It is recognized that it may not benecessary or possible to record all of the data for all types oftests; however, this practice is considered a basic approach fordata collection.1.3 This s

4、tandard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Significance and Use2.

5、1 This practice provides a basic approach for recordingthe preparation, parameters, and results of field slip resistancetesting. It is intended to assist those performing such tests indocumenting information gathered for further analysis, inpreparation for writing a final report, or for record keepi

6、ngpurposes.2.2 Potential users include those performing slip resistancetesting in the field, such as industrial and commercial safetyprofessionals, facility management and maintenance person-nel, forensic engineers, insurance company and broker losscontrol specialists, and research personnel.3. Repo

7、rt3.1 Report the following information for test preparation(see Fig. 1):3.1.1 Client/customer.3.1.2 Location/address.3.1.3 Date and time of test(s).3.1.4 ASTM test method used.3.1.5 Name of tribometer operator and employing company.3.1.6 Address and telephone number of tribometer operator.3.1.7 Type

8、 of tribometer (for example, brand and model)and serial number.3.1.8 Test foot preparation protocol.3.2 Report the following information for test parameters andresults:3.2.1 Specific floor location and orientation of the tribom-eter where the test was performed.3.2.2 Type of test foot material (for

9、example, Neolite testliner, leather, or nitrile rubber).3.2.3 Slope of the surface being tested.3.2.4 Floor material and texture.3.2.5 Floor FinishIndicate the type of finish (for example,type of wax, polish, or paint) applied, if any. Also indicate thecondition of the finish.3.2.6 Floor ConditionsI

10、ndicate if clean or contaminated.If clean, indicate the method of cleaning. If contaminated,indicate the type, continuity, and thickness of the contaminant.3.2.7 Wet or dry testing.3.2.8 Temperature and relative humidity (if relevant).3.2.9 Tribometer reading.3.3 Provide any comments pertinent to th

11、e testing.4. Keywords4.1 floor testing; report form; report framework; slip resis-tance; slip test data; tribometer; walkway testing1This practice is under the jurisdiction of ASTM Committee F13 on Safety andTraction for Footwear and is the direct responsibility of Subcommittee F13.10onTraction.Curr

12、ent edition approved June 10, 2000. Published August 2000.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in conne

13、ctionwith any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any suchpatent rights, and the risk of infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsi

14、ble technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Headquarters. Your comments will receive careful consideration at

15、 a meeting of the responsibletechnical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make yourviews known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM, 100 Barr Harbor Drive, PO Box C

16、700, West Conshohocken, PA 19428-2959, United States.Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website (www.astm.org).FIG. 1 Sample Slip Resistance Test Results ReportF 20482