ASTM E1977-2011 Standard Specification for Shelter Tactical Expandable One-Side《技术上可膨胀单面外罩的标准规格》.pdf
《ASTM E1977-2011 Standard Specification for Shelter Tactical Expandable One-Side《技术上可膨胀单面外罩的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM E1977-2011 Standard Specification for Shelter Tactical Expandable One-Side《技术上可膨胀单面外罩的标准规格》.pdf(15页珍藏版)》请在麦多课文档分享上搜索。
1、Designation:E197705 Designation: E1977 11Standard Specification forShelter, Tactical, Expandable, One-Side1This standard is issued under the fixed designation E1977; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last
2、revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers a rigid wall, on
3、e-side expandable shelter constructed of aluminum-faced, nonmetallic honeycombsandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification in thetransport mode. Nominal dimensions when closed (container mode) are: height 8 ft, width 8 ft, and le
4、ngth 20 ft.ft (2.4 by 2.4 by6.1 m) Approximate dimensions, when expanded (shelter mode) are: height 8 ft, width 15 ft, and length 20 ft (2.4 by 4.6 by 6.1m).1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units values given in parentheses aremathematical conversi
5、ons to SI units that are provided for information only and are not considered standard.1.3 The following precautionary statement pertains to the test method portion only. Section 7, of this specification; Thisstandard does not purport to address all of the safety concerns, if any, associated with it
6、s use. It is the responsibility of the userof this standard to establish appropriate safety and health practices and determines the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2E864 Practice for Surface Preparation of Aluminum Alloys to Be Adhesively
7、 Bonded in Honeycomb Shelter PanelsE865 Specification for Structural Film Adhesives for Honeycomb Sandwich PanelsE866 Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in HoneycombShelter PanelsE874 Practice for Adhesive Bonding of Aluminum Facings to
8、 Nonmetallic Honeycomb Core for Shelter PanelsE990 Specification for Core-Splice Adhesive for Honeycomb Sandwich Structural PanelsE1091 Specification for Nonmetallic Honeycomb Core for Use in Shelter PanelsE1749 Terminology Relating to Rigid Wall Relocatable SheltersE1773 Practice for Sealing Rigid
9、Wall Tactical Shelters with Polysulfide Based SealantsE1826 Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloysto Be Adhesively BondedE1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures2.2 ISO Standa
10、rds:3ISO 1161-1980 Series 1-Freight Containers-Corner Fittings, SpecificationISO 1496/I Series 1-Freight Containers-Specification and Testing Part I-General Cargo ContainersISO 9001 Quality SystemsModel for Quality Assurance in Design, Development, Production, Installation, and Servicing2.3 Military
11、 Standards:4MIL-STD-129 Marking for Shipping and StorageMIL-STD-810 Environmental Engineering Considerations and Laboratory Tests2.4 ANSI/ASQC Standard: ANSI/ASQC Standards:5ANSI/ASQC 21.4-1993 Sampling Procedures and Tables for Inspection by Attributes1This specification is under the jurisdiction o
12、f ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materialsand Processes for Durable Rigidwall Relocatable Structures.Current edition approved MaySept. 1, 2005.2011. Published May 2005.October 2011. Originally approved in 1998. Last previous
13、edition approved in 20042005 asE1977 045. DOI: 10.1520/E1977-05.10.1520/E1977-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary pag
14、e on the ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla
15、.mil.5Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Milwaukee, WI 53203, http:/www.asq.org.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit
16、may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Ha
17、rbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.5 Drawings:65-4-2828 Shelter, Shelter, Assembly, One-Side Expandable-60 amp5-4-3200 Shelter, Assembly, One-Side Expandable-100 amp65-4-3200 Shelter, Assembly, One-Side Expandable-100 amp66Copies of drawings are available from
18、 U.S. Army Natick Soldier Center, ATTN: AMSRD-NSC-CP-CS, Kansas Street, Natick, MA 01760-5018, http:/www.natick.army.mil.E1977 1122.6 SAE StandardsSAE Standards:7SAE-AMS-STD-1595 Qualification of Aircraft, Missile, and Aerospace Fusion WeldingSAE-AMS-STD-2219 Fusion Welding for Aerospace Application
19、s3. General Requirements3.1 Alternate ComponentsWhen this specification or the referenced drawings specify use of a specific component “or equal,”the contractor may substitute a component equal to the specified component provided that the contractor complies with thefollowing requirements. Prior to
20、manufacture of the first article, or if none is required, prior to commencing production, thecontractor shall submit for the purchasers approval a list identifying each proposed “or equal” component together with proof thateach listed component is functionally equal to the specified component and is
21、 compatible with the end item covered by thisspecification. The purchaser, at his option, may require a physical sample of any “or equal” component. Approval of the submittedlisting and supporting data authorizes the commencement of fabrication of the first article or of production, as applicable, b
22、ut doesnot relieve the contractor of the responsibility that the “or equal” components perform in accordance with specified requirementswhen incorporated into the end item.3.2 Materials and ComponentsMaterials and components shall conform to the documents listed in Section 2 and as specifiedherein.
23、Any change to the proposed materials or processes must be approved by the purchaser. It is encouraged that recycledmaterial be used when practical as long as it meets the requirements of this specification.3.3 WorkmanshipThe shelter, including all parts and accessories, shall be constructed and fini
24、shed in a workmanlike mannerwith particular attention given to removal of burrs and sharp edges, accuracy of dimensions, thoroughness of soldering, welding,painting, alignment of parts of assemblies, and the tightness of screws, bolts, and so forth. Gaskets shall not be torn or split andshall be fre
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME19772011STANDARDSPECIFICATIONFORSHELTERTACTICALEXPANDABLEONESIDE 技术上 膨胀 单面 外罩 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-529965.html