ASTM E1241-2005(2013) Standard Guide for Conducting Early Life-Stage Toxicity Tests with Fishes《用鱼进行早期生命阶段毒性测试的标准指南》.pdf

《ASTM E1241-2005(2013) Standard Guide for Conducting Early Life-Stage Toxicity Tests with Fishes《用鱼进行早期生命阶段毒性测试的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1241-2005(2013) Standard Guide for Conducting Early Life-Stage Toxicity Tests with Fishes《用鱼进行早期生命阶段毒性测试的标准指南》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1241 05 (Reapproved 2013)Standard Guide forConducting Early Life-Stage Toxicity Tests with Fishes1This standard is issued under the fixed designation E1241; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide describes procedures for obtaining laboratorydata concerning the adverse effects of a test material added t

3、odilution waterbut not to foodon certain species of fresh-water and saltwater fishes during 28 to 120-day (depending onspecies) continuous exposure, beginning before hatch andending after hatch, using the flow-through technique. Thisguide will probably be useful for conducting early life-stagetoxici

4、ty tests with some other species of fish, although modi-fications might be necessary.1.2 Other modifications of these procedures might be justi-fied by special needs or circumstances. Although using appro-priate procedures is more important than following prescribedprocedures, results of tests condu

5、cted using unusual proceduresare not likely to be comparable to results of many other tests.Comparison of results obtained using modified and unmodifiedversions of these procedures might provide useful informationconcerning new concepts and procedures for conducting earlylife-stage toxicity tests wi

6、th fishes.1.3 These procedures are applicable to all chemicals, eitherindividually or in formulations, commercial products, orknown mixtures, that can be measured accurately at thenecessary concentrations in water. With appropriate modifica-tions these procedures can be used to conduct tests ontempe

7、rature, dissolved oxygen, and pH and on such materialsas aqueous effluents (see Guide E1192), leachates, oils, par-ticulate matter, sediments, and surface waters.1.4 This guide is arranged as follows:SectionReferenced Documents 2Terminology 3Summary of Standard 4Significance and Use 5.1Hazards 6Appa

8、ratus 7Facilities 7.1Construction Materials 7.2Metering System 7.3Test Chambers and Incubation Cups 7.4Cleaning 7.5Acceptability 7.6Dilution Water 8Requirements 8.1Source 8.2Treatment 8.3Characterization 8.4Test Material 9General 9.1Stock Solution 9.2Test Concentration(s) 9.3Test Organisms 10Species

9、 10.1Age 10.2Source 10.3Brood Stock 10.4Handling 10.5Procedure 11Experimental Design 11.1Dissolved Oxygen 11.2Temperature 11.3Beginning the Test 11.4Thinning 11.5Feeding 11.6Duration of Test 11.7Biological Data 11.8Other Measurements 11.9Analytical Methodology 12Acceptability of Test 13Calculation o

10、f Results 14Documentation 15AppendixesAppendix X1 Salmon, Trout, and CharAppendix X2 Northern pikeAppendix X3 Fathead minnowAppendix X4 White suckerAppendix X5 Channel catfishAppendix X6 Bluegill1This guide is under the jurisdiction of ASTM Committee E47 on BiologicalEffects and Environmental Fatean

11、d is the direct responsibility of SubcommitteeE47.01 on Aquatic Assessment and Toxicology.Current edition approved March 1, 2013. Published March 2013. Originallyapproved in 1988. Last previous edition approved in 2005 as E1241 05. DOI:10.1520/E1241-05R13.Copyright ASTM International, 100 Barr Harbo

12、r Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Appendix X7 Gulf toadfishAppendix X8 Sheepshead minnowAppendix X9 SilversidesAppendix X10 Statistical GuidanceAppendix X11. Striped Bass1.5 This standard does not purport to address all of thesafety concerns, if any, associated wi

13、th its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific hazardstatements are given in Section 6 and 9.2. Referenced Documents2.1 ASTM Standards:2E380 Pract

14、ice for Use of the International System of Units(SI) (the Modernized Metric System) (Withdrawn 1997)3E729 Guide for Conducting Acute Toxicity Tests on TestMaterials with Fishes, Macroinvertebrates, and Amphib-iansE943 Terminology Relating to Biological Effects and Envi-ronmental FateE1023 Guide for

15、Assessing the Hazard of a Material toAquatic Organisms and Their UsesE1192 Guide for Conducting Acute Toxicity Tests on Aque-ous Ambient Samples and Effluents with Fishes,Macroinvertebrates, and AmphibiansE1203 Practice for Using Brine Shrimp Nauplii as Food forTest Animals in Aquatic Toxicology (Wi

16、thdrawn 2013)33. Terminology3.1 The words “must,” “should,” “may,” “can,” and “might”have very specific meanings in this standard. “Must” is used toexpress an absolute requirement, that is, to state that the testought to be designed to satisfy the specified condition, unlessthe purpose of the test r

17、equires a different design. “Must” isonly used in connection with factors that directly relate to theacceptability of the test (see 13.1). “Should” is used to statethat the specified condition is recommended and ought to bemet if possible. Although violation of one “should” is rarely aserious matter

18、, violation of several will often render the resultsquestionable. Terms such as “is desirable,” “is often desirable,”and “might be desirable” are used in connection with lessimportant factors. “May” is used to mean “is (are) allowed to,”“can” is used to mean “is (are) able to,” and “might” is used t

19、omean “could possibly.” Thus the classic distinction between“may” and “can” is preserved, and “might” is never used as asynonym for either “may” or “can.”3.2 Definitions:3.2.1 For definitions of other terms used in this standard,refer to Guide E729, Terminology E943, and Guide E1023. Foran explanati

20、on of units and symbols, refer to Practice E380.3.2.2 antagonisma situation which an effect of an expo-sure to multiple substances is less than would be expected if theknown effects of the individual substances were added to-gether.3.2.3 synergisma situation in which an effect of an expo-sure to mul

21、tiple substances is more than would be expected ifthe known effects of the individual substances were addedtogether.3.2.4 confoundinga situation in which one or more othervariables covary with the independent variable, making itimpossible to determine the influence of the independentvariable on the

22、dependent variable.4. Summary of Guide4.1 In each of two or more treatments, embryos and thesubsequent larvae of one species of fish are maintained in twoor more test chambers in a flow-through system for 28 to 120days, depending upon species. In each of the one or morecontrol treatments, the embryo

23、s and larvae are maintained indilution water to which no test material has been added in orderto provide (a) a measure of the acceptability of the test bygiving an indication of the quality of the embryos and larvaeand the suitability of the dilution water, food, test conditions,handling procedures,

24、 and so forth, and (b) the basis forinterpreting data obtained from the other treatments. In each ofthe one or more other treatments, the embryos and larvae aremaintained in dilution water to which a selected concentrationof test material has been added. Specified data on the concen-tration of test

25、material and the survival and growth of theembryos and larvae in each test chamber are obtained andanalyzed to determine the effect(s) of the test material on thesurvival and growth of the test organisms.5. Significance and Use5.1 Protection of a species requires prevention of unaccept-able effects

26、on the number, weight, health, and uses of theindividuals of that species. An early life-stage toxicity testprovides information about the chronic toxicity of a testmaterial to a species of fish. The primary adverse effectsstudied are reduced survival and growth.5.2 Results of early life-stage toxic

27、ity tests are generallyuseful estimates of the results of comparable life-cycle testswith the same species (1).4However, results of early life-stagetests are sometimes under estimative of those obtained with thesame species in the longer life-cycle tests (2).5.3 Results of early life-stage toxicity

28、tests might be used topredict long-term effects likely to occur on fish in fieldsituations as a result of an exposure under comparableconditions, except that motile organisms might avoid exposurewhen possible.5.4 Results of early life-stage toxicity tests might be used tocompare the chronic sensitiv

29、ities of different fish species andthe chronic toxicities of different materials, and to study theeffects of various environmental factors on results of such tests.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Boo

30、k of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Boldface numbers in parentheses refer to the list of references at the end of thisguide.E1241 05 (2013)25.5 Resu

31、lts of early life-stage toxicity tests might be animportant consideration when assessing the hazards of materi-als to aquatic organisms (see Guide E1023) or when derivingwater quality criteria for aquatic organisms (3).5.6 Results of an early life-stage test might be useful forpredicting the results

32、 of chronic tests on the same test materialwith the same species in another water or with another speciesin the same or a different water. Most such predictions take intoaccount the results of acute toxicity tests, and so the usefulnessof the results of an early life-stage test is greatly increased

33、byreporting also the results of an acute toxicity test (see GuideE729) conducted with juveniles of the same species under thesame conditions.5.7 Results of early life-stage toxicity tests might be usefulfor studying the biological availability of, and structure-activity relationships between, test m

34、aterials.5.8 Results of early life-stage toxicity tests will depend ontemperature, composition of the dilution water, condition of thetest organisms, and other factors.6. Hazards6.1 Many materials can affect humans adversely if precau-tions are inadequate. Therefore, skin contact with all testmateri

35、als and solutions of them should be minimized by suchmeans as wearing appropriate protective gloves (especiallywhen washing equipment or putting hands in test solutions),laboratory coats, aprons, and glasses, and by using dip nets,forceps, or tubes, to remove organisms from test solutions.Special pr

36、ecautions, such as covering test chambers andventilating the area surrounding the chambers, should be takenwhen conducting tests on volatile materials. Information ontoxicity to humans (4), recommended handling procedures (5),and chemical and physical properties of the test material shouldbe studied

37、 before a test is begun. (WarningSpecial proce-dures might be necessary with radiolabeled test materials (6)and with test materials that are, or are suspected of being,carcinogenic (7).6.2 Although disposal of stock solutions, test solutions, andtest organisms poses no special problems in most cases

38、, healthand safety precautions and applicable regulations should beconsidered before beginning a test. Removal or degradation oftest material might be desirable before disposal of stock andtest solutions.6.3 Cleaning of equipment with a volatile solvent such asacetone should be performed only in a w

39、ell-ventilated area inwhich no smoking is allowed and no open flame, such as a pilotlight, is present. (WarningAn acidic solution should not bemixed with a hypochlorite solution because hazardous fumesmight be produced.6.4 To prepare dilute acid solutions, concentrated acidshould be added to water,

40、not vice versa. Opening a bottle ofconcentrated acid and adding concentrated acid to water shouldbe performed only in a fume hood.6.5 Because dilution water and test solutions are usuallygood conductors of electricity, use of ground fault systems andleak detectors should be considered to help avoid

41、electricalshocks. Salt water is such a good conductor that protectivedevices are strongly recommended.7. Apparatus7.1 FacilitiesFlow-through tanks should be available forculturing brood stock, and for holding and acclimating testorganisms. The test chambers should be in a constant-temperature area o

42、r recirculating water bath. An elevatedheadbox might be desirable so dilution water can be gravity-fed into holding, acclimation, and culture tanks, and themetering system (see 7.3). Strainers and air traps should beincluded in the water-supply system. Headboxes and holding,acclimation, culture, and

43、 dilution-water tanks should beequipped for temperature control and aeration (see 8.3). Airused for aeration should be free of fumes, oil, and water; filtersto remove oil and water are desirable. Filtration of air througha 0.22 m bacterial filter might be desirable.The facility shouldbe well ventila

44、ted and free of fumes. To further reduce thepossibility of contamination by test materials and other sub-stances (especially volatile ones) holding, acclimation, andculture tanks should not be in a room in which toxicity tests areconducted, stock solutions or test solutions are prepared, orequipment

45、 is cleaned. During holding, acclimation, culture,and testing, organisms should be shielded from disturbanceswith curtains or partitions to prevent unnecessary stress. Atiming device should be used to control the photoperiod (seeAppendix X1-Appendix X9).A15- to 30-min transition period(8) might be d

46、esirable whenever the lights go on to reduce thepossibility of organisms being stressed by large, suddenincreases in light intensity. A transition period when the lightsgo off might also be desirable.7.2 Construction MaterialsEquipment and facilities thatcome in contact with stock solutions, test so

47、lutions, or anywater into which test organisms will be placed should notcontain substances that can be leached or dissolved by aqueoussolutions in amounts that adversely affect fish. In addition,equipment and facilities that contact stock solutions or testsolutions should be chosen to minimize sorpt

48、ion of testmaterials from water.7.2.1 Glass, Type 316 Stainless Steel, Nylon, and Fluoro-carbon PlasticsUse whenever possible to minimizedissolution, leaching, and sorption, except that stainless steelshould not be used for tests on metals in salt water.7.2.2 Concrete and Rigid PlasticsMay be used f

49、orholding, acclimation, and culture tanks and in the water-supplysystem, but these materials should be soaked, preferably inflowing dilution water, for a week or more before use (9). Castiron pipe should not be used with salt water and probablyshould not be used in a freshwater-supply system becausecolloidal iron will be added to the dilution water and strainerswill be needed to remove rust particles. A specially designedsystem is usually necessary to obtain salt water from a naturalwater source (see Guide E729). Dilution water, stock solutions,or test solutions should n