ASTM D5188-2004a Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber Method)《测定燃料汽-液比温度的试验方法(真空室法)》.pdf

《ASTM D5188-2004a Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber Method)《测定燃料汽-液比温度的试验方法(真空室法)》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5188-2004a Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber Method)《测定燃料汽-液比温度的试验方法(真空室法)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5188 04aAn American National StandardStandard Test Method forVapor-Liquid Ratio Temperature Determination of Fuels(Evacuated Chamber Method)1This standard is issued under the fixed designation D 5188; the number immediately following the designation indicates the year oforiginal adopt

2、ion or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This test method covers the determination of the tem-perature at which

3、the vapor formed from a selected volume ofvolatile petroleum product saturated with air at 0 to 1C (32 to34F) produces a pressure of one atmosphere in an evacuatedchamber of fixed volume. This test method is applicable tosamples for which the determined temperature is between 36and 80C (97 and 176F)

4、 and the vapor-liquid ratio is between8 to 1 and 75 to 1.NOTE 1When the vapor-liquid ratio is 20:1, the result is intended tobe comparable to the results determined by Test Method D 2533.NOTE 2This test method may also be applicable at pressures otherthan one atmosphere, but the stated precision may

5、 not apply.1.2 This test method is applicable to both gasoline andgasoline-oxygenate blends.1.2.1 Some gasoline-oxygenate blends may show a hazewhen cooled to 0 to 1C. If a haze is observed in 11.5, it shallbe indicated in the reporting of results. The precision and biasstatements for hazy samples h

6、ave not been determined (seeNote 9).1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the us

7、er of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specificwarnings, see 7.2 and 8.1.1.2. Referenced Documents2.1 ASTM Standards:2D 2533 Test Method for Vapor-Liquid Ratio of Spark-Ignition Engine Fue

8、lsD 2892 Test Method for Distillation of Crude Petroleum(15-Theoretical Plate Column)D 4057 Practice for Manual Sampling of Petroleum andPetroleum Products3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 T(V/L = 20), nthe equilibrium temperature at whichthe partial pressure of

9、a sample under test conditions is equalto 101.3 kPa (14.69 psia) and the vapor-liquid ratio is 20.3.1.2 vapor-liquid ratio of a fuel, nthe ratio at a specifiedtemperature and pressure of the volume of vapor in equilibriumwith liquid to the volume of sample charged, as a liquid, at 0C(32F).4. Summary

10、 of Test Method4.1 A known volume of chilled, air-saturated sample isintroduced into an evacuated, thermostatically controlled testchamber of known volume. The sample volume is calculated togive the desired vapor-liquid ratio for the chamber volume inuse. After injection, the chamber temperature is

11、adjusted untila stable chamber pressure of 101.3 kPa (14.69 psia) isachieved.5. Significance and Use5.1 The tendency of a fuel to vaporize in automotive enginefuel systems is indicated by the vapor-liquid ratio of the fuel.5.2 Automotive fuel specifications generally include T(V/L = 20) limits to en

12、sure products of suitable volatility perfor-mance. For high ambient temperatures, a fuel with a high valueof T(V/L = 20), indicating a fuel with a low tendency to vaporize,is generally specified; conversely for low ambient tempera-tures, a fuel with a low value of T(V/L = 20)is specified.6. Apparatu

13、s6.1 Apparatus suitable for use shall employ a small volumetest chamber incorporating a transducer for pressure measure-ments and associated equipment for thermostatically control-ling the chamber temperature, evacuating the test chamberprior to sample introduction, and cleaning and purging the1This

14、 test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.08 on Volatility.Current edition approved April 1, 2004. Published April 2004. Originallyapproved in 1991. Last previous edition approved in 2004 as D

15、518804.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of t

16、his standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.chamber following the test. Critical elements of the apparatusshall meet the following specifications:6.1.1 Test Chamber, constructed of stainless steel or alumi-num, design

17、ed to contain between 5 and 50 mL of liquid plusvapor with a tolerance of 61 % of the nominal capacity.NOTE 3The test chamber volumes of the instruments used for the1991 cooperative test program to determine the precision and biasstatements were between 5 and 15 mLof liquid plus vapor with a toleran

18、ceof 61 % of the nominal capacity.6.1.2 Pressure Transducer, minimum operational rangefrom 1 to 177 kPa (0 to 25.6 psia) with minimum resolution of0.1 kPa (0.01 psi) and minimum accuracy of 60.8 kPa (60.12psi). The pressure measurement system shall include associ-ated electronics and readout devices

19、 to display the resultingpressure reading.6.1.3 Heater, thermostatically controlled heater capable ofmaintaining the test chamber within 0.1C of the set tempera-ture for a minimum of 5 min.NOTE 4The use of automated instruments that automatically adjustthe temperature, after sample injection, to giv

20、e a pressure of 101.3 kPa(14.69 psia) is allowed.6.1.4 Platinum Resistance Thermometer, used to measurethe temperature of the test chamber, having a minimumtemperature range of 36 to 80C, minimum resolution of 0.1C(0.2F) and minimum accuracy of 60.1C (60.2F).6.2 Vacuum Pump, capable of reducing the

21、pressure in thetest chamber to less than 0.01 kPa (0.001 psia).6.3 Syringes, (if required for sample introduction), gas-tight, 1- to 20-mL capacity with minimum accuracy andprecision of 61%.6.4 Bath, iced water or air, for chilling the samples andsyringe (if required) to between 0 and 1C (32 to 34F)

22、.6.5 Pressure Measuring Device, capable of measuring localstation pressure with an accuracy of 0.20 kPa (0.03 psi) orbetter, at the same elevation relative to sea level as theapparatus in the laboratory.6.5.1 When a mercury manometer is not used as thepressure measuring device, the calibration of th

23、e pressuremeasuring device employed shall be periodically checked(with traceability to a nationally recognized standard) to ensurethat the device remains within the required accuracy specifiedin 6.5.6.6 McLeod Vacuum Gage or Calibrated Electronic VacuumMeasuring Device for Calibration, to cover at l

24、east the rangefrom 0.01 to 0.67 kPa (0.1 to 5 mm Hg). The calibration of theelectronic vacuum measuring device shall be regularly verifiedin accordance with the annex section on Vacuum Sensors(A6.3) of Test Method D 2892.7. Reagents and Materials7.1 Purity of ReagentsUnless otherwise indicated, allr

25、eagents shall conform to the specifications of the Committeeon Analytical Reagents of the American Chemical Society3where such specifications are available. Lower purities can beused, provided it is first ascertained that the reagent is ofsufficient purity to permit its use without lessening the acc

26、u-racy of the determination. Reagents used for performancechecks (see 10.3) shall be of at least 99 % purity.7.2 n -pentane, (WarningFlammable, health hazard.)8. Sampling8.1 General:8.1.1 Conduct bulk sampling to obtain the laboratorysamples in accordance with Practice D 4057 except forgasoline-oxyg

27、enate blends where water displacement is notused. The extreme sensitivity of T(V/L)measurements to lossesthrough evaporation and the resulting changes in compositionis such as to require the utmost precaution and the mostmeticulous care in the handling of samples. (WarningExtremely flammable, harmfu

28、l if inhaled or ingested. Skinirritant on repeated contact. Aspiration hazard.)8.1.2 The size of the sample container from which thesample is taken shall be 1 L (1 qt). It shall be 70 to 80 % filledwith sample.8.1.3 The precision statement will be derived using samplesin 1-L (1-qt) containers. Howev

29、er, samples taken in containersof other sizes as prescribed in Practice D 4057 can be used ifit is recognized that the precision could be affected. In the caseof referee testing, the 1-L (1-qt) sample is mandatory.8.1.4 Perform the T(V/L)determination on the first testspecimen withdrawn from the sam

30、ple container. Do not use theremaining sample in the container for a second T(V/L)determi-nation. If a second determination is necessary, obtain a newsample.8.1.5 Protect samples from excessive temperature prior totesting. This can be accomplished by storage in an appropriateice bath or refrigerator

31、.8.1.6 Do not test samples stored in leaky containers. Discardand obtain a new sample if leaks are detected.8.2 Sampling TemperatureCool the sample container andcontents in an iced bath or refrigerator to between 0 and 1C(32 to 34F) prior to opening the sample container. Ensuresufficient time to rea

32、ch this temperature by direct measurementof the temperature of a similar liquid in a like container placedin the cooling bath at the same time as the sample.8.3 Verification of Sample Container Filling:8.3.1 With the sample at a temperature of 0 to 1C, take thecontainer from the cooling bath or refr

33、igerator and wipe drywith absorbent material. If the container is not transparent,3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for La

34、boratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.D 5188 04a2unseal it and using a suitable gage, confirm that the samplevolume equals 70 to 80 % of the container capacity (see Note5).

35、If the sample is contained in a transparent glass container,verify that the container is 70 to 80 % full by suitable means(see Note 5).8.3.2 Discard the sample if the container is filled to less than70 % by volume of the container capacity.8.3.3 If the container is filled to more than 80 % by volume

36、,pour out enough sample to bring the container contents towithin the 70 to 80 % by volume range. Do not return anysample to the container once it has been withdrawn.NOTE 5For non-transparent containers, one way to confirm that thesample volume equals 70 to 80 % of the container capacity is to use ad

37、ipstick that has been pre-marked to indicate the 70 and 80 % containercapacities. The dipstick should be of such material that it shows wettingafter being immersed and withdrawn from the sample. To confirm thesample volume, insert the dipstick into the sample container so that ittouches the bottom o

38、f the container at a perpendicular angle, beforeremoving the dipstick. For transparent containers, using a marked ruler orby comparing the sample container to a like container which has the 70and 80 % levels clearly marked, has been found suitable.8.3.4 Reseal the container, if necessary, and return

39、 thesample container to the cooling bath or refrigerator.8.4 Air Saturation of the Sample in the Sample Container:8.4.1 Transparent Container OnlySince 8.3.1 does notrequire that the sample container be opened to verify thesample capacity, it is necessary to unseal the cap momentarilybefore resealin

40、g it, so that samples in transparent containers aretreated the same as samples in non-transparent containers.8.4.2 With the sample again at a temperature of 0 to 1C,take the container from the cooling bath or refrigerator, wipe itdry with an absorbent material, remove the cap momentarily,taking care

41、 that no water enters, reseal and shake vigorously.Return it to the bath or refrigerator for a minimum of 2 min.9. Preparation of Apparatus9.1 Prepare the instrument for operation in accordance withthe manufacturers instructions.9.2 Clean and dry the test chamber to avoid contaminationof the test sa

42、mple.9.3 Prior to sample introduction, visually determine fromthe instrument display that the test chamber pressure is stableand does not exceed 0.1 kPa (0.01 psia). If the pressure is notstable or exceeds this value, check that the chamber containsno volatile materials from a previous sample, the s

43、eals aresatisfactory, the calibration of the transducer is correct, and theapparatus does not leak.9.4 If a syringe is used for introduction of the sample, chillthe syringe to between 0 and 1.0C (32 to 34F) in arefrigerator or ice bath before drawing in the sample. Thesyringe must be kept completely

44、 dry during this cooling. Placethe clean and dry syringe in a water tight plastic bag and placethe sealed bag in the ice bath or refrigerator maintained at 0 to1.0C (32 to 34F).9.5 Prior to introduction of the test specimen, set thetemperature of the test chamber to close to the expected result,if k

45、nown; or 40C (104F), if unknown.10. Calibration10.1 Calibrate the pressure transducer at least every 30 daysor when needed as indicated by the performance check (see10.3). The calibration of the transducer is accomplished usingtwo reference points, zero pressure, and ambient barometricpressure.NOTE

46、6Pressure transducers can be sensitive to working temperature.Calibration should be performed at the test chamber temperature mostfrequently used.10.1.1 Connect a McLeod gage or a calibrated electronicvacuum measuring device to the vacuum source in line with thetest chamber. Apply vacuum to the test

47、 chamber. When thevacuum measuring device registers a pressure less than 0.1 kPa(0.8 mm Hg) adjust the indicator to zero or to the actualreading on the vacuum measuring device as dictated by theinstrument design or manufacturers instructions.10.1.2 Open the test chamber to the atmosphere and observe

48、the indicator reading. If the pressure reading is not equal to theambient barometric pressure, adjust the indicator span controluntil the appropriate reading is observed. Ensure that theinstrument is set to display the total pressure and not acalculated or corrected value.10.1.3 Repeat 10.1.1 and 10

49、.1.2 until the zero and baromet-ric pressure read correctly without further adjustments.10.2 Calibrate the platinum resistance thermometer andindicator used to monitor the temperature of the test chamberat least every six months against a National Institute ofStandards and Technology (NIST) traceable thermometer.10.3 Check the performance of the instrument each day it isin use by running a sample consisting of air saturatedn-pentane, T(V/L = 20)= 36.1C (96.9F). Handle the perfor-mance check material in the same manner as a sample (seeSections