ASTM D3241-2013 Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels《航空涡轮机燃料热氧化稳定性的标准试验方法》.pdf

《ASTM D3241-2013 Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels《航空涡轮机燃料热氧化稳定性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3241-2013 Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels《航空涡轮机燃料热氧化稳定性的标准试验方法》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3241 12D3241 13 An American National StandardDesignation 323/99Standard Test Method forThermal Oxidation Stability of Aviation Turbine Fuels1This standard is issued under the fixed designation D3241; the number immediately following the designation indicates the year oforiginal adoptio

2、n or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Sco

3、pe*1.1 This test method covers the procedure for rating the tendencies of gas turbine fuels to deposit decomposition products withinthe fuel system.1.2 The differential pressure values in mm Hg are defined only in terms of this test method.1.3 The values stated in SI units are to be regarded as stan

4、dard. No other units of measurement are included in this standard.1.4 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause centralnervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Ca

5、utionshould be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet(MSDS) for details and EPAs websitehttp:/www.epa.gov/mercury/faq.htmfor additional information. Users should be awarethat selling mercury and/or mercury containing product

6、s into your state or country may be prohibited by law.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability o

7、f regulatorylimitations prior to use. For specific warning statements, see 6.1.1, 7.2, 7.2.1, 7.3, 11.1.1, and Annex A3.2. Referenced Documents2.1 ASTM Standards:2D1655 Specification for Aviation Turbine FuelsD4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contaminatio

8、nE177 Practice for Use of the Terms Precision and Bias in ASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method2.2 ISO Standards:3ISO 3274 Geometrical Product Specifications (GPS)Surface Texture: Profile MethodNominal Characteristics Of Co

9、ntact(Stylus) InstrumentsISO 4288 Geometrical Product Specifications (GPS)Surface Texture: Profile MethodRules And Procedures For TheAssessment Of Surface Texture2.3 ASTM Adjuncts:4Color Standard for Tube Deposit Rating3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 depositsde

10、posits, noxidative products laid down on the test area of the heater tube or caught in the test filter, or both.1 This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.J0.03on Combustion and Thermal

11、Properties.Current edition approved Nov. 1, 2012May 1, 2013. Published February 2013May 2013. Originally approved in 1973. Last previous edition approved in 20112012 asD324111a.12. DOI: 10.1520/D3241-12.10.1520/D3241-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactA

12、STM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http:

13、/www.iso.org.4 Available from ASTM International Headquarters. Order Adjunct No. ADJD3241. Original adjunct produced in 1986.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becaus

14、eit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears

15、 at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.1.1 DiscussionFuel deposits will tend to predominate at the hottest portion of the heater tube, which is between the 30-mm and 50-mm position.3.1.2 heater

16、 tubetube, nan aluminum coupon controlled at elevated temperature, over which the test fuel is pumped.3.1.2.1 DiscussionThe tube is resistively heated and controlled in temperature by a thermocouple positioned inside. The critical test area is the thinnerportion, 60 mm in length, between the shoulde

17、rs of the tube. Fuel inlet to the tube is at the 0-mm position, and fuel exit is at 60mm.3.2 Abbreviations:3.2.1 Pdifferential pressure.4. Summary of Test Method4.1 This test method for measuring the high temperature stability of gas turbine fuels uses an instrument that subjects the testfuel to con

18、ditions that can be related to those occurring in gas turbine engine fuel systems. The fuel is pumped at a fixed volumetricflow rate through a heater, after which it enters a precision stainless steel filter where fuel degradation products may becometrapped.4.1.1 The apparatus uses 450 mL of test fu

19、el ideally during a 2.5-h test. The essential data derived are the amount of depositson an aluminum heater tube, and the rate of plugging of a 17 m nominal porosity precision filter located just downstream of theheater tube.5. Significance and Use5.1 The test results are indicative of fuel performan

20、ce during gas turbine operation and can be used to assess the level of depositsthat form when liquid fuel contacts a heated surface that is at a specified temperature.6. Apparatus6.1 Aviation Fuel Thermal Oxidation Stability Tester5SixEight models of suitable equipment may be used as indicated inTab

21、le 1.6.1.1 Portions of this test may be automated. Refer to the appropriate user manual for the instrument model to be used for adescription of detailed procedure. A manual is provided with each test rig. (WarningNo attempt should be made to operate theinstrument without first becoming acquainted wi

22、th all components and the function of each.)6.1.2 Certain operational parameters used with the instrument are critically important to achieve consistent and correct results.These are listed in Table 2.6.2 Heater Tube Deposit Rating Apparatus:6.2.1 Visual Tube Rater, the tuberator described in Annex

23、A1.6.3 Because jet fuel thermal oxidation stability is defined only in terms of this test method, which depends upon, and isinseparable from, the specific equipment used, the test method shall be conducted with the equipment used to develop the testmethod or equivalent equipment.5 The following equi

24、pment, as described in Table 1 and RR:D02-1309, was used to develop this test method. The following equipment, as described in Table 1 anddetermined as equivalent in testing as detailed in RR:D02-1631, is provided by PAC, 8824 Fallbrook Drive, Houston, TX 77064. The following equipment, as described

25、 inTable 1 and determined as equivalent in testing as detailed in RR:D02-1728, is provided by Falex Corporation, 1020 Airpark Dr., Sugar Grove, IL, 60554-9585. This is notan endorsement or certification by ASTM International.TABLE 1 Instrument ModelsInstrument Model Pressurize With Principle Differe

26、ntial Pressure by202A nitrogen gear Hg Manometer; No Record203A nitrogen gear Manometer + Graphical Record215A nitrogen gear Transducer + Printed Record230A hydraulic syringe Transducer + Printout240A hydraulic syringe Transducer + Printout230 Mk IIIB hydraulic dual piston (HPLC Type) Transducer + P

27、rintoutF400C hydraulic dual piston (HPLC Type) Transducer + Printout230 Mk IVD hydraulic single piston (HPLC Type) Transducer + PrintoutA See RR:D02-1309.B See RR:D02-1631.C See RR:D02-1728.D See RR:D02-1757.D3241 1327. Reagents and Materials7.1 Use distilled (preferred) or deionized water in the sp

28、ent sample reservoir as required for Model 230 and 240 instruments.7.2 Use methyl pentane, 2,2,4-trimethylpentane, or n-heptane (technical grade, 95 mol % minimum purity) as general cleaningsolvent. This solvent will effectively clean internal metal surfaces of apparatus before a test, especially th

29、ose surfaces (before thetest section) that contact fresh sample. (Warning Extremely flammable. Harmful if inhaled (see Annex A3).)7.2.1 Use trisolvent (equal mix of acetone (1), toluene (2), and isopropanol (3) as a specific solvent to clean internal (working)surface of test section only. (Warning(1

30、) Extremely flammable, vapors may cause flash fire; (2) and (3) Flammable. Vapors ofall three harmful. Irritating to skin, eyes, and mucous membranes.)7.3 Use dry calcium sulfate + cobalt chloride granules (97 + 3 mix) in the aeration dryer. This granular material changesgradually from blue to pink

31、color indicating absorption of water. (WarningDo not inhale dust or ingest. May cause stomachdisorder.)TABLE 2 Critical Operating Characteristics of D3241 InstrumentsItem DefinitionTest apparatus Tube-in-shell heat exchanger as illustrated in Fig. 1.Test coupons:Heater tube A, B, C Specially fabrica

32、ted aluminum tube that produces controlledheated test surface; new one for each test. An electronic recordingdevice, such as a radio-frequency identification device (RFID),may be embedded into the heater tube rivet located at the bottomof the heater tube.Tube identification Each heater tube may be p

33、hysically identified with a unique serialnumber, identifying the manufacturer and providing traceability tothe original material batch. This data may be stored on an elec-tronic recording device, such as a RFID, embedded into the heatertube.Tube metallurgy 6061-T6 Aluminum, plus the following criter

34、iaa) The Mg:Si ratio shall not exceed 1.9:1b) The Mg2Si percentage shall not exceed1.85 %Tube dimensions: Dimension ToleranceTube length, mm 161.925 0.254Center section length, mm 60.325 0.051Outside diameters, mmShoulders 4.724 0.025Center section 3.175 0.051Inside diameter, mm 1.651 0.051Total ind

35、icator runout, mm, max 0.013Mechanical surface finish, nm, in accordance with ISO 3274and ISO 4288 using the mean of four 1.25measurements50 20Test filter 5 nominal 17-m stainless steel mesh filter element to trap deposits;new one for each testInstrument parameters:Sample volume 600 mL of sample is

36、aerated, then this aerated fuel is used to fillthe reservoir leaving space for the piston; 450 45 mL may bepumped in a valid testAeration rate 1.5 L/min dry air through spargerFlow during test 3.0 10 % mL/min (2.7 min to 3.3 max)Pump mechanism positive displacement, gear or piston syringeCooling bus

37、 bars fluid cooled to maintain consistent tube temperature pro-fileThermocouple (TC) Type J, fiber braid or Iconel sheathed, or Type K, Iconel sheathedOperating pressure:System 3.45 MPa 10 % on sample by pressurized inert gas (nitrogen) orby hydraulically transmitted force against control valve outl

38、et re-strictionAt test filter differential pressure (P) measured across test filter (by mercurymanometer or by electronic transducer) in mm HgOperating temperature:For test as stated in specification for fuelUniformity of run maximum deviation of 2C from specified temperatureCalibration pure tin at

39、232C (and for Models 230 and 240 only, pure lead at327C for high point and ice + water for low point reference)A The following equipment, heater tubes, manufactured by PAC, 8824 Fallbrook Drive, Houston, TX 77064, was used in the development of this test method. This is notan endorsement or certific

40、ation by ASTM International.B Atest protocol to establish equivalence of heater tubes is on file atASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1550.C The following equipment, heater tube and filter kits, manufactured by Falex Corporation, 1020Airpark Dr.,

41、 Sugar Grove, IL, 60554-9585, was run through the test protocolin RR:D02-1550 and determined as equivalent to the equipment used to develop the test method. This test is detailed in RR:D02-1714. This is not an endorsement orcertification by ASTM International.D3241 1338. Standard Operating Condition

42、s8.1 Standard conditions of the test method are as follows:8.1.1 Fuel Quantity, 450-mL minimum for test + about 50 mL for system.8.1.2 Fuel Pre-TreatmentFiltration through a single layer of general purpose, retentive, qualitative filter paper followed by a6-min aeration at 1.5 L/min air flow rate fo

43、r a maximum of 1000 mLsample using a coarse 12-mm borosilicate glass gas dispersiontube.8.1.3 Fuel System Pressure, 3.45 MPa (500 psi) 610 % gauge.8.1.4 Thermocouple Position, at 39 mm.8.1.5 Fuel System Prefilter Element, filter paper of 0.45-m pore size.8.1.6 Heater Tube Control Temperature, preset

44、 as specified in applicable specification.8.1.7 Fuel Flow Rate, 3.0 mL/min 6 10 %.8.1.8 Minimum Fuel Pumped During Test, 405 mL.8.1.9 Test Duration, 150 6 2 min.8.1.10 Cooling Fluid Flow, approximately 39 L/h, or center of green range on cooling fluid meter.8.1.11 Power Setting, approximately 75 to

45、100 on non-computer models; internally set for computer models.9. Preparation of Apparatus9.1 Cleaning and Assembly of Heater Test Section:9.1.1 Clean the inside surface of the heater test section using a nylon brush saturated with trisolvent material to remove alldeposits.9.1.2 Check the heater tub

46、e to be used in the test for surface defects and straightness by referring to the procedure in AnnexA1.10. Be careful, also, to avoid scratching tube shoulder during the examination, since the tube shoulder must be smooth to ensurea seal under the flow conditions of the test.9.1.3 Assemble the heate

47、r section using new items: (1) visually checked heater tube, (2) test filter, and (3) three O-rings. Inspectinsulators to be sure they are undamaged.NOTE 1Heater tubes must not be reused. Tests indicate that magnesium migrates to the heater tube surface under normal test conditions. Surfacemagnesium

48、 may reduce adhesion of deposits to reused heater tube.9.1.4 During assembly of heater section, handle tube carefully so as not to touch center part of tube. IF CENTER OF HEATERTUBE IS TOUCHED, REJECT THE TUBE SINCE THE CONTAMINATED SURFACE MAY AFFECT THE DEPOSIT-FORMING CHARACTERISTICS OF THE TUBE.

49、9.2 Cleaning and Assembly of Remainder of Test Components:9.2.1 Perform the following steps in the order shown prior to running a subsequent test.NOTE 2It is assumed that the apparatus has been disassembled from previous test (see AnnexA2 or appropriate user manual for assembly/disassemblydetails).9.2.2 Inspect and clean components that contact test sample and replace any seals that are faulty or suspect especially the (1)lip seal on piston, and (2) O-rings on the reservoir cover, lines, and prefilter cover.9.2.3 Install prepared