ASTM B176-2008(2013) Standard Specification for Copper-Alloy Die Castings《铜合金压铸件标准规格》.pdf

《ASTM B176-2008(2013) Standard Specification for Copper-Alloy Die Castings《铜合金压铸件标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B176-2008(2013) Standard Specification for Copper-Alloy Die Castings《铜合金压铸件标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B176 08 (Reapproved 2013)Standard Specification forCopper-Alloy Die Castings1This standard is issued under the fixed designation B176; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification establishes the requirements forcopper-al

3、loy die castings. The alloys specified are CopperAlloy UNS Nos. C85700, C85800, C86500, C87800, C99700,and C99750.21.2 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided forinformation on

4、ly and are not considered standard.2. Referenced Documents2.1 ASTM Standards:3B824 Specification for General Requirements for CopperAlloy CastingsB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE23 Test Methods for Notched Bar Impact Testing

5、 of Me-tallic MaterialsE255 Practice for Sampling Copper and Copper Alloys forthe Determination of Chemical CompositionE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2 American Die Casting Institute:4“E” Series Product Standards2.3 Federal Standard:5Fed. Std. No.

6、 123 Marking for Shipment (Civil Agencies)2.4 Military Standards:5MIL-STD-129 Marking for Shipment and Storage (MilitaryAgencies)MIL-P-116 Methods of Preservation3. General Requirements3.1 The following sections of Specification B824 constitutea part of this specification.3.1.1 Terminology (Section

7、3),3.1.2 Number of Tests and Retests (Section 10) (Note tousers: Paragraph 10.3 of Specification B824 applies only whenmechanical requirements are specified in the purchase order.),3.1.3 Test Methods (Section 12),3.1.4 Significance of Numerical Limits (Section 13),3.1.5 Inspection (Section 14),3.1.6

8、 Rejection and Rehearing (Section 15),3.1.7 Certification (Section 16),3.1.8 Test Report (Section 17),3.1.9 Product Marking (Section 18), and3.1.10 Supplementary Requirements.3.2 In addition, when a section with a title identical to thatreferenced in 3.1, above, appears in this specification, itcont

9、ains additional requirements which supplement those ap-pearing in Specification B824.4. Terminology4.1 For general terms related to copper and copper alloys,refer to Terminology B846.5. Ordering Information5.1 Include the following information when placing ordersfor die castings under this specifica

10、tion as applicable:5.1.1 Specification title, number, and year of issue,5.1.2 Part name and number,5.1.3 Copper Alloy UNS Number,5.1.4 Quantity and delivery schedule, as required,5.1.5 Engineering drawing of die casting, when required,giving all necessary dimensions and tolerances and showinglatest

11、revisions and allowances for machining, if any. Locationof ejector pin marks or parting lines shall be at the option of themanufacturer unless specifically designated on the drawing.1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct respon

12、sibility of Subcommittee B05.05 onCastings and Ingots for Remelting.Current edition approved Oct. 1, 2013. Published November 2013. Originallyapproved in 1942. Last previous edition approved in 2008 as B176 08. DOI:10.1520/B0176-08R13.2The UNS system for copper and copper alloys (see Practice E527)

13、is a simpleexpansion of the former standard designation system accomplished by the additionof a prefix “C” and a suffix “00”. The suffix can be used to accommodatecomposition variations of the base alloy.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Se

14、rvice at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from the American Die Casting Institute, 2340 Des Plaines Ave., DesPlaines, IL 60018.5Available from DLA Document Services, Building 4/D, 700 Robb

15、ins Avenue,Philadelphia, PA 19111-5094, http:/quicksearch.dla.mil/Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.6 When die castings are purchased for agencies of theU.S. government the Supplementary Requirements of Specifi-catio

16、n B824 may be specified.5.2 The following requirements are optional and should bespecified in the purchase order when required.5.2.1 Inspection lot sampling (Section 8),5.2.2 Chemical analysis of residual elements (Section 4),5.2.3 Soundness requirements (Section 9),5.2.4 Mechanical requirements (Se

17、ction 5),5.2.5 Special requirements (Section 9),5.2.6 Certification (Specification B824),5.2.7 Foundry test report (Specification B824),5.2.8 Witness inspection (Specification B824),5.2.9 Product marking (Specification B824), and5.2.10 Packaging requirements (Section 12).6. Chemical Composition6.1 T

18、he castings shall conform to the requirements formajor elements as shown in Table 1.6.2 These specification composition limits do not precludethe presence of other elements. Limits may be established andanalysis required for unnamed elements agreed upon betweenthe manufacturer or supplier and the pu

19、rchaser. Copper or zincmay be given as remainder and may be taken as the differencebetween the sum of all elements analyzed and 100 %. When allnamed elements in Table 1 are analyzed, their sum shall be asspecified in Table 2.6.3 It is recognized that residual elements may be present incast copper-ba

20、se alloys. Analysis shall be made for residualelements only when specified in the purchase order.6.4 If the producers or suppliers method of compositioncontrol is acceptable, sampling for chemical analysis may bewaived at the discretion of the purchaser.7. Mechanical Property Requirements7.1 Unless

21、specified in the purchase order, acceptance of diecastings under this specification shall not depend on mechani-cal properties determined by tension or impact tests. TableX1.1 shows typical mechanical properties.7.2 When minimum mechanical properties are specified inthe purchase order the mechanical

22、 properties shall be agreedupon between the manufacturer or supplier and the purchaser.8. Dimensions, Mass, and Permissible Variations8.1 Permissible variations in dimensions shall be within thelimits specified on the drawings or in the contract or purchaseorder.8.1.1 Any dimensions for which a tole

23、rance is not specifiedshall be in accord with ADCI Product Standard Series E1 toE16 inclusive.9. Sampling9.1 An inspection lot shall consist of the production fromeach die or compound die on each machine for each 24 hduring the first week of normal operation and the productionfor each 48 h thereafte

24、r of normal operation. Any significantchange in the machine, composition, die or continuity ofoperation shall be considered as the start of a new lot. Diecastings inspected by this method shall be so marked orhandled during the finishing operations as not to lose theiridentity.9.2 Each die casting o

25、f a randomly selected sample shall beexamined to determine conformance to the requirements withTABLE 1 Chemical RequirementsComposition, % max (unless shown as a range or min)CopperAlloyUNSNo.Major Elements Residual ElementsCopper Tin Lead Zinc IronNickelinclu-dingCobaltAlumi-numManga-neseSilicon Ir

26、onAnti-monyNickelCobaltSulphurPhos-phorousAlumi-numManga-neseSiliconC85700 58.064.0A0.501.50.81.532.040.0. . . . . 0.7 . 1.0 . . 0.8 . 0.05C85800 57.0 minA1.5 1.5 31.041.0. . . . . 0.50 0.05 0.50 0.05 0.01 0.55 0.25 0.25BC86500 55.060.0A1.0 0.40 36.042.00.402.0. 0.501.50.101.5. . . 1.0 . . . . .C878

27、00 80.0 minA0.25 0.09 12.016.0. . . . 3.84.20.15 0.05 0.20 0.05 0.01 0.15 0.15B,CC99700 54.0 minA1.0 2.0 19.025.0. 4.06.00.503.011.015.0. 1.0 . . . . . . .C99750 55.061.0. 0.502.517.023.0. 5.0 0.253.017.023.0. 1.0D. . . . . . .AIn determining copper min, copper may be determined as copper plus nicke

28、l.BArsenic 0.05 max.CMagnesium 0.01 max.DIron content above the nickel content may cause hard spots resulting in decreased machinability.TABLE 2 Sum of All Named Elements AnalyzedCopper AlloyUNS No.Copper Plus NamedElements, % minC85700 98.7C85800 98.7C86500 99.0C87800 99.5C99700 99.7C99750 99.7B176

29、 08 (2013)2respect to general quality, dimensions and identification mark-ing. The producer or supplier may use a system of statisticalquality control for such examinations.9.3 Sampling for Chemical AnalysisRefer to the Samplingsection of Specification B824 and Practice E255 for samplingmethodology.

30、10. Special Requirements10.1 Internal SoundnessWhen specified, the soundness ofdie castings shall conform to standards or requirements agreedupon between the producer or supplier and the purchaser. Thenumber and extent of imperfections shall not exceed thosespecified by the purchaser. The standards

31、or requirements mayconsist of radiographs, photographs or sectioned die castings.10.2 Imperfections inherent in the die castings shall not because for rejection provided it is demonstrated that the diecastings are in accordance with the requirements and standardsagreed upon.10.3 WorkmanshipDie casti

32、ngs shall be of uniformquality, free of injurious discontinuities that will adverselyaffect their serviceability.10.4 FinishWhen specified in the contract or purchaseorder the as-cast surface finish required shall conform tostandards agreed upon between the purchaser and the produceror supplier, or

33、as prescribed in ADCI Product Standard.10.5 Pressure TightnessWhen specified in the contract orpurchase order the pressure tightness of die castings shallconform to standards agreed upon between the purchaser andthe producer or supplier, or as prescribed in ADCI ProductStandard.11. Test Methods11.1

34、Analytical chemical methods are given in SpecificationB824 (Section 13).11.2 When tension or impact tests are made, the tension testspecimen shown in Fig. 18, Standard Tension Test Specimensfor Die Castings, of Test Methods E8/E8M and the impact testspecimen shown in Fig. 6, Charpy (Simple-Beam) Imp

35、act TestSpecimens, Types A, B, and C, of Test Methods E23, shall beused.12. Packaging and Package Marking12.1 PackagingUnless otherwise specified, the die cast-ings shall be packaged to provide adequate protection duringnormal handling and transportation. Each package shall con-tain only one type of

36、 item unless otherwise agreed upon. Thetype of packaging and gross weight of containers shall, unlessotherwise agreed upon, be at the producers discretion, pro-vided they are such as to ensure acceptance by common orother carriers for safe transportation at the lowest rate to thedelivery point.12.2

37、MarkingEach shipping container shall be legiblymarked with the purchase order number, gross and net weights,and the suppliers name or trademark. Marking for shipmentshall be in accordance with Fed. Std. No. 123 for civil agenciesand MIL-STD-129 for Military agencies.12.3 PreservationMaterial intende

38、d for prolonged storagein unheated locations shall be adequately packed and protectedto avoid deterioration and damage. When specified in thecontract or purchase order, material shall be preserved,packaged, and packed in accordance with the requirements ofMIL-P-116. The applicable levels shall be as

39、 specified in thecontract or order.13. Keywords13.1 copper-alloy castings; die castings; UNS No. C85700;UNS No. C85800; UNS No. C86500; UNS No. C87800; UNSNo. C99700; UNS No. C99750APPENDIXES(Nonmandatory Information)X1. TYPICAL MECHANICAL PROPERTIESX1.1 The data in Table X1.1 do not constitute a pa

40、rt of thisspecification. They will indicate to the purchaser the mechani-cal properties that may be expected of test specimens whenmade in a die, the test specimens being cast in a test bar die andconforming to the chemical composition specified. It should bethoroughly understood that the following

41、figures representdie-cast test specimens and not specimens cut from commercialdie-cast parts. In the tension testing of die-cast brassspecimens, the rate of stressing up to the yield strength shallnot exceed 100 ksi (700 MPa)/min. Exceedingly slow rates oftesting may result in creep and hence are to

42、 be avoided.Beyond the yield strength, the rate of straining shall not exceed0.25 in./in.min measured on the gage length of the specimen.B176 08 (2013)3X2. CHARACTERISTICSX2.1 Table X2.1 shows certain casting and other outstand-ing characteristics which are usually considered when selectinga die cas

43、ting alloy for a specific application.X3. METRIC EQUIVALENTSX3.1 The SI unit for strength properties (MPa) is in accor-dance with the International System of Units (SI). The derivedSI unit for force is the newton (N), which is defined as thatforce which when applied to a body having a mass of onekil

44、ogram gives it an acceleration of one metre per secondsquared (N = kgm/s2). The derived SI unit for pressure orstress is the newton per square metre (N/m2), which has beennamed the pascal (Pa) by the General Conference on Weightsand Measures. Since 1 ksi = 6 894 757 Pa the metric equiva-lents are ex

45、pressed as megapascal (MPa), which is the same asMN/m2and N/mm2.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any suc

46、h patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invite

47、d either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a

48、fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this

49、standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE X1.1 Typical Mechanical Properties of Test SpecimensACopper AlloyUNS No.Tensile Strength,ksi (MPa)Yield Strengthpsi (0.2% Offset),ksi (MPa)Elongation in 2 in.,(50 mm) %Impact Strength Charpy,ftlbf (J)Hardness,Rockwell BModulus ofElasticity(103)