EN 61243-1-2005 en Live working C Voltage detectors Part 1 Capacitive type to be used for voltages exceeding 1 kV a c (Incorporates Amendment A1 2010)《带电作业 电压检测器 第1部分 超过1 KV的交流电压用的.pdf

《EN 61243-1-2005 en Live working C Voltage detectors Part 1 Capacitive type to be used for voltages exceeding 1 kV a c (Incorporates Amendment A1 2010)《带电作业 电压检测器 第1部分 超过1 KV的交流电压用的.pdf》由会员分享，可在线阅读，更多相关《EN 61243-1-2005 en Live working C Voltage detectors Part 1 Capacitive type to be used for voltages exceeding 1 kV a c (Incorporates Amendment A1 2010)《带电作业 电压检测器 第1部分 超过1 KV的交流电压用的.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61243-1:2005 Live working Voltage detectors Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c. ICS 13.260; 29.240.99 +A1:2010National foreword This British Standard is the UK implementation of EN 61243-1:2005+A1:2010. It is identical with IEC 61243-1:2003, inc

2、orporating amendment 1:2009. It supersedes BS EN 61243-1:2005 which will be withdrawn on 1 December 2012. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to the IEC text carry the number or the amendment. For example, text alt

3、ered by IEC amendment 1 is indicated in the text by !“. The UK participation in its preparation was entrusted to Technical Committee PEL/78, Tools for live working. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to

4、 include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 61243-1:2005+A1:2010 This British Standard was published under the authority of the Standards Policy and Str

5、ategy Committee on 19 August 2005 BSI 2011 Amendments/corrigenda issued since publication Date Comments 31 March 2011 Implementation of IEC amendment 1:2009; with CENELEC endorsement A1:2010. ISBN 978 0 580 64540 2 EUROPEAN STANDARD EN 61243-1:2005+A1 NORME EUROPENNE EUROPISCHE NORM February 2010 CE

6、NELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worl

7、dwide for CENELEC members. ICS 29.240.99 English version Supersedes EN 61243-1:2005 Ref. No. EN 61243-1:2005 E This European Standard was approved by CENELEC on 2005-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eu

8、ropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (E

9、nglish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austri

10、a, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Live working Voltage detectors Par

11、t 1: Capacitive type to be used for voltages exceeding 1 kV a.c. (IEC 61243-1:2003, modified) Travaux sous tension Dtecteurs de tension Partie 1: Type capacitif pour usage sur des tensions alternatives de plus de 1 kV (CEI 61243-1:2003, modifie) Arbeiten unter Spannung Spannungsprfer Teil 1: Kapazit

12、ive Ausfhrung fr Wechselspannungen ber 1 kV (IEC 61243-1:2003, modifiziert) 2 Foreword The text of the International Standard IEC 61243-1:2003, prepared by IEC TC 78, Live working, together with the common modifications prepared by the Technical Committee CENELEC TC 78, Equipment and tools for live

13、working, was submitted to the formal vote and was approved by CENELEC as EN 61243-1 on 2005-03-01. This European Standard supersedes EN 61243-1:1997 + A1:1997 + corrigendum June 1999. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication o

14、f an identical national standard or by endorsement (dop) 2006-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-03-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61243-1:2003 was approved

15、by CENELEC as a European Standard with agreed common modifications.Foreword to amendment A1 The text of document 78/751/CDV, future amendment 1 to IEC 61243-1:2003, prepared by IEC TC 78, Live working, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 6

16、1243-1:2005 on 2009-11-17. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amend

17、ment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-09-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2012-12-01 As a consequence of endorsing amendment 1:2009 to IEC 6124

18、3-1:2003, the common modifications in EN 61243-1:2005 are now covered by the IEC text. _ Endorsement notice The text of amendment 1:2009 to the International Standard IEC 61243-1:2003 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 61243-1:2005+A1:2

19、010 EN 61243-1:2005+A1:2010 (E) 3 CONTENTS INTRODUCTION.4 1 Scope 5 2 Normative references .5 3 Terms and definitions .6 4 Requirements .10 4.1 General requirements 10 4.2 Functional requirements 11 4.3 Electrical requirements 13 4.4 Mechanical requirements .13 4.5 Markings .15 4.6 Instructions for

20、use 16 5 Specific requirements .16 5.1 For insulating element of a voltage detector as a complete device 16 5.2 For indicator casing of voltage detector as a separate device .16 6 Tests16 6.1 General .16 6.2 Function tests18 6.3 Dielectric tests.25 6.4 Mechanical tests29 7 Specific tests31 7.1 Leaka

21、ge current for voltage detector as a complete device .31 8 Conformity assessment of voltage detectors having completed the production phase33 Annex A (normative) Suitable for live working; double triangle 49 Annex B (normative) Instructions for use 50 Annex C (normative) Chronology of tests51 Annex

22、D (informative) Sampling procedure .52 Annex E (normative) Mechanical shock tests Pendulum method.54 5 5 5 Annex ZA (normative) Normative references to international publications with their corresponding European publications57 8Bibliography 5 6 6 6 BS EN 61243-1:2005+A1:2010 EN 61243-1:2005+A1:2010

23、 (E) Annex G (informative) In-service care G.1 General . G.2 Testing . 4 INTRODUCTION This International Standard has been prepared according to the requirements of IEC 61477, where applicable. BS EN 61243-1:2005+A1:2010 EN 61243-1:2005+A1:2010 (E) 5 LIVE WORKING VOLTAGE DETECTORS Part 1: Capacitive

24、 type to be used for voltages exceeding 1 kV a.c. 1 Scope This part of IEC 61243 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 765 kV a.c., and frequencies of 50 Hz and/or 60 Hz. This part applies only to

25、 voltage detectors of capacitive type used in contact with the part to be tested, as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this standard (see 4.4.1 for general design). Other types of

26、voltage detectors are not covered by this part of the standard. Some restrictions on their use are applicable in the case of factory-assembled switchgear and on overhead systems of electrified railways (see Annex B, instructions for use). NOTE Except where otherwise specified, all the voltages defin

27、ed in this standard refer to values of phase-to- phase voltages of three-phase systems. In other systems, the applicable phase-to-phase or phase-to-earth (ground) voltages should be used to determine the operating voltage. 2 Normative references The following referenced documents are indispensable f

28、or the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60060-1:1989, High-voltage test techniques Part 1: General definitions and test requirements IEC 60

29、068-1, Environmental testing -Part 1: General and guidance IEC 60068-2-6:1995, Environmental testing Tests Test Fc and guidance: Vibration (sinusoidal) IEC 60068-2-14:1984, Environmental testing Tests Test N: Change of temperature Amendment 1 (1986) IEC 60068-2-32:1975, Environmental testing Tests T

30、est Ed: Free fall Amendment 2 (1990) IEC 60071-1:2006, Insulation co-ordination Part 1: Definitions, principles and rules ! “ BS EN 61243-1:2005+A1:2010 EN 61243-1:2005+A1:2010 (E) 6 _ IEC 60417-DB:2002 1 , Graphical symbols for use on equipment IEC 60942, Electroacoustics Sound calibrators IEC 6126

31、0:1995, Electroacoustics Octave-band and fractional-octave-band filters IEC 61477:2001, Live working Minimum requirements for the utilization of tools, devices and equipment Amendment 1 (2002) 2IEC 61672-1:2002, Electroacoustics Sound level meters Part 1: Specifications ISO 286-1:1988, ISO system of

32、 limits and fits Part 1: Bases of tolerances, deviations and fits ISO 286-2:1988, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 3744:1994, Acoustics Determination of sound power levels of noise sources using sound pressure Eng

33、ineering method in an essentially free field over a reflecting plane CIE (International Commission on Illumination) 15.2:1986, Colorimetry 3 Terms and definitions 3.1 voltage detector 3.2 voltage detector of capacitive type device whose operation is based on the current passing through the stray cap

34、acitance to earth (ground) NOTE The term voltage detector is used in this document for voltage detector of capacitive type. 1“DB” refers to the IEC on-line database. 2There exists a consolidated edition 1.1 (2002) that includes edition 1 and its amendment. For the purposes of this document, the term

35、s and definitions given in IEC 61318:2007 and the following apply. ! “ device used to provide clear evidence of the presence or the absence of the operating voltage NOTE For example, voltage detectors can be described as capacitive type or resistive type. Definition 11.2.5 of IEC 60743, modified, an

36、d IEV 651-10-04, modified ! “ BS EN 61243-1:2005+A1:2010 EN 61243-1:2005+A1:2010 (E) IEC 61318:2007, Live working Conformity assessment applicable to tools, devices and equipment ! “ 7 3.3 designs of voltage detectors different constructions of voltage detectors, either as a complete device with or

37、without contact electrode extension, or as a separate device intended to be equipped with an insulating stick, with or without contact electrode extension NOTE Some parts such as the contact electrode, the contact electrode extension (if existing), or the insulating element of a voltage detector as

38、a complete device may be dismantled. 3.4 family of voltage detectors 3.5 contact electrode bare conductive part of the conductive element which establishes the electric connection to the component to be tested IEV 651-10-09 3.6 contact electrode extension externally insulated conductive element betw

39、een the indicator and the contact electrode, intended to achieve the correct position of the indicator relative to the installation being tested 3.7 indicator part of the voltage detector which indicates the presence or absence of the operating voltage at the contact electrode IEV 651-10-08, modifie

40、d 3.8 adaptor part of a voltage detector as a separate device which permits attachment of an insulating stick 3.9 insulating element part of a voltage detector as a complete device that provides adequate safety distance and insulation to the user 3.10 insulating stick 3.11 limit mark distinctive loc

41、ation or mark to indicate to the user the physical limit to which the voltage detector may be inserted between live parts or may touch them for testing purposes, a group of voltage detectors, delimited by a minimum and a maximum rated voltage, that are identical in design (including dimensions) and

42、only differ by their nominal voltages or nominal voltage ranges ! “ insulating tool essentially made of an insulating tube and/or rod with end fittings Definition 2.5.1 of IEC 60743 and IEV 651-02-01 NOTE For voltage detection, an insulating stick is intended to be attached to a voltage detector as

43、a separate device in order to provide the length to reach the installation to be tested and adequate safety distance and insulation to the user. ! “ BS EN 61243-1:2005+A1:2010 EN 61243-1:2005+A1:2010 (E) 8 3.12 hand guard distinctive physical guard separating the handle from the insulating element N

44、OTE Its purpose is to prevent the hands from slipping and passing into contact with the insulating element. 3.13 testing element built-in or external device, by means of which the functioning of the voltage detector can be checked by the user IEV 651-10-11, modified 3.14 accessories items used to le

45、ngthen the handle or the contact electrode, to improve the efficiency of the contact electrode or to enable the contact electrode to reach the part to be tested 3.15 nominal voltage U nsuitable approximate value of voltage used to identify a system or device IEV 601-01-21, modified NOTE The nominal

46、voltage of the voltage detector is the parameter associated with its clear indication. A voltage detector may have more than one nominal voltage, or a nominal voltage range. Limit values of the nominal voltage range are named U nmin and U nmax. 3.16 operating voltage (in a system) value of the volta

47、ge under normal conditions, at a given instant and a given point of the system NOTE This value may be expected, estimated or measured. IEV 601-01-22 3.17 threshold voltage U tminimum voltage between the live part and earth (ground) required to give a clear indication corresponding to specific condit

48、ions as defined in the corresponding test NOTE As defined in this part of IEC 61243, threshold voltage is related to specific test conditions. Users should be aware that their requirements for threshold voltage for field operation need to be related to the test conditions in the standard. 3.18 rated

49、 voltage U rvalue of voltage generally agreed upon by manufacturer and customer, to which certain operating specifications are referred. The rated voltage of the voltage detector is the voltage selected from IEC 60071-1, Tables 2 and 3, column 1, which should either be equal to the nominal voltage (or the highest n