EN 12544-1-1999 en Non-Destructive Testing - Measurement and Evaluation of the X-Ray Tube Voltage - Part 1 Voltage Divider Method《无损检验 X射线管电压的评估和测量 第1部分 电压分压法》.pdf

《EN 12544-1-1999 en Non-Destructive Testing - Measurement and Evaluation of the X-Ray Tube Voltage - Part 1 Voltage Divider Method《无损检验 X射线管电压的评估和测量 第1部分 电压分压法》.pdf》由会员分享，可在线阅读，更多相关《EN 12544-1-1999 en Non-Destructive Testing - Measurement and Evaluation of the X-Ray Tube Voltage - Part 1 Voltage Divider Method《无损检验 X射线管电压的评估和测量 第1部分 电压分压法》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、STD.BSI BS EN 12544-1-ENGL 1999 1624669 0839930 232 I BRITISH STANDARD Non-des truc tive testing - Measurement and evaluation of the X-ray tube voltage - Part 1: Voltage divider method The European Standard EN 12544-1:1999 has the status of a British Standard ICs 19.100 NO COPYING WITHOUT BSI PERMIS

2、SION EXCEPT AS PERMITTED BY COPYRIGHT LAW I BS EN 125 - present to the responsible European committee any enquiries on the intepretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of or

3、ganizations represented on this committee can be obained on request to its secretary. Cross-references The British Standards which implement intemational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitied ”Intemational Standar

4、ds Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include a31 the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard

5、 does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice dtsplayed in this document indicates when the document was last issued. ISBN O 580 351

6、69 6 - STD-BSI BS EN 12544-1-ENGL L999 1b24bb9 D19932 O95 I EUROPEAN STANDARD NORME EUROPENNE EROPaSCHE NORM EN 12544-1 September 1999 ICs 19,100 English version Non destructive testing - Measurement and evaluation of the X-ray tube voltage - Part I : Voltage divider method Essais non destructifs -

7、Mesurage et valuation de la tension des tubes radiognes - Partie 1: Mthode par deviseur de tension Zerstrungsfreie Prfung - Messung und Auswertung der Rntgenrhrenspannung - Teil 1 : Spannungsteiler- Verfahren This European Standard was approved by CEN on 16 August 1999. CEN members are bound to comp

8、ly with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards may be obtained on application to the Central Sec

9、retariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by traislation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as he ofic

10、ial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic. Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT

11、EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 8-1050 Brussels Q 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12544-1:1999 E Page 2 EN 12!544-1:1999 Contents Page Foreword 3

12、 Introduction , . _. . . . . 4 1 Scope . 4 2 Principle 4 3 Measurement 5 4 Test report 5 O BSI 12-1999 Page 3 EN 12544-1:1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 138 “Nondestructive testing“, the Secretariat of which is held by AFNOR. This European Standar

13、d shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2000, and conflicting national standards shall be withdrawn at the latest by March 2000. According to the CENICENELEC Internal Regulations, the national standards

14、organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. In the framework

15、 of its scope, Technical Committee CEN/TC 138 entrusted CEN/TC 138MIG 1 “Ionizing Radiation“ with preparing the following standard: EN 12544-1, Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 7: Voltage divider method. EN 12544-1 is a part of series of European

16、Standards; the other parts are the following: EN 12544-2, Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 2: Constancy check by the thick filter method EN 12544-3, Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 3: Spectrome

17、tric method. O BSI 12-1999 Page 4 EN 12544-1:1999 Introduction In order to cover the different requirements for the measurement of the X-ray tube voltage, three different methods are described in EN 12544-1 to EN 12544-3. The voltage divider method (EN 12544-1) enables a direct and absolute measurem

18、ent of the average high voltage of constant potential X-ray systems on the secondary side of the high voltage generator. The thick filter method (EN 12544-2) describes a constancy check. This method is recommended for the regular stabiliiy check of an X-ray system. The spectrometric method (EN 12544

19、-3) is a procedure for non-invasive measurement of the X-ray tube voltage using the energy spectrum of the X-rays. This method can be applied for all X-ray systems and is the recommended method whenever the voltage divider method is not applicable, e. g. in case of tank units where it is not possibl

20、e to connect the voltage divider device. 1 Scope This European Standard specifies a method for the direct and absolute measurement of the average high voltage of constant potential (DC) X-ray systems on the secondary side of the high voltage generator. The intention is to check the correspondence wi

21、th t,he indicated high voltage value on the control unit of the X-ray system. This method is applied to assure a reproducible operation of X-ray systems because the voltage influences particularly the penetration of materials and the contrast of X-ray images and also the requirements concerning the

22、radiation protection. 2 Principle The principle of the voltage divider method is presented in figure 1 : I 1 1 From generator 2 To X-ray tube 3 Analog exit Figure I - Scheme of the voltage divider O BSI 12-1999 STD-BSI BS EN 12544-1-ENGL 2999 LbZ4bb 0819736 730 m Page 5 EN 12544-1 1 A999 The voltage

23、 divider system consists of: - a box with two high voltage connectors; - a resistor chain Ri, RP; - an analog exit for the voltage drop at R2; - a measuring device, e.g. a voltmeter or an oscilloscope. The value of the resistors should be chosen for a current of less than 10 % of the actual tube cur

24、rent. The resistor chain shall have a temperature coefficient of I 50 x IO“/C in relation to the resistor value. The output voltage across the resistor or 3 % for general radiographic and radioscopic applications. b) 3 Measurement For measuring purposes the measuring device is connected between the

25、high voltage generator and the X-ray tube. The high voltage is devided by means of the resistor chain, presented as i$ and R2 in figure 1, and the drop voltage is measured at R2 using a voltmeter or an oscilloscope. 4 Testreport The test report shall contain at least the following details: the X-ray

26、 system with type and serial number; the working conditions of the X-ray system, e.g. tube current, tube voltage, temperature; the accuracy of the measuring device; the date of measurement; a table with the result(s) and a comparison between the actual and the indicated values; name and signature of

27、 the operator. O BSI 12-1999 1 BSEN 12544-1: 1999 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the inkrnational level. It is incorpo

28、rated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

29、 finding an inaccuracy or ambigwty while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service caiied PLUS

30、which ensures that subscribers automatically receive the latest editions of sandars. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standar

31、ds, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informaon on national, European and inkmational standards through its Library and its Technical Help to Expo

32、rters Service. Various BSI electronic information services axe also available which give details on all its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial

33、 discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrati on. Tel: 020 8996 7002. Fax: 020 8996 7001. copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international s

34、tandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no exmct may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does n

35、ot preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or e designations. If these details are to be used for any other purpose thi implementation then the prior written pennission of BSI must be obtained. if permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.