EN 10223-4-2012 1706 Steel wire and wire products for fencing and netting - Part 4 Steel wire welded mesh fencing《钢丝和钢丝产品击剑和网 第4部分 焊接钢丝网击剑》.pdf

《EN 10223-4-2012 1706 Steel wire and wire products for fencing and netting - Part 4 Steel wire welded mesh fencing《钢丝和钢丝产品击剑和网 第4部分 焊接钢丝网击剑》.pdf》由会员分享，可在线阅读，更多相关《EN 10223-4-2012 1706 Steel wire and wire products for fencing and netting - Part 4 Steel wire welded mesh fencing《钢丝和钢丝产品击剑和网 第4部分 焊接钢丝网击剑》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10223-4:2012Steel wire and wire productsfor fencing and nettingPart 4: Steel wire welded mesh fencingCopyright European Committee for Standardization Provided by IHS under

2、license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10223-4:2012. It supersedes BS EN 10223-4:1998, which is withdrawn.The UK participation in its p

3、reparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. User

4、s are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 64501 3 ICS 77.140.65 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority

5、 of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

6、-BS EN 10223-4:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10223-4 November 2012 ICS 77.140.65 Supersedes EN 10223-4:1998English Version Steel wire and wire products for fencing and netting - Part 4: Steel wire welded mesh fencing Fils et produits trfils en acier pour cltures et grillag

7、es - Partie 4: Grillage en acier soud Stahldraht und Drahterzeugnisse fr Zune und Drahtgeflechte - Teil 4: Geschweite Gitter aus Stahldraht fr Zune This European Standard was approved by CEN on 13 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

8、 the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Stand

9、ard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nati

10、onal standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slo

11、vakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved

12、worldwide for CEN national Members. Ref. No. EN 10223-4:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (E) 2 Contents Page Foreword 31 S

13、cope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .65 Manufacture 65.1 Base metal 65.2 Fabrication 65.2.1 Rolls 65.2.2 Panels .75.3 Welding .76 Requirements .76.1 Tensile strength .76.2 Tolerance on wire diameters 76.3 Coatings 76.3.1 Zinc and zinc

14、 alloy coatings .76.3.2 Organic material coatings .86.4 Tolerance on mesh dimensions .86.5 Weld shear strength 87 Sampling and testing 88 Inspection documentation 99 Test methods 99.1 Tensile test .99.2 Wire dimension 99.3 Weld shear strength 99.4 Coating tests 99.4.1 Zinc or zinc alloy coating of w

15、ire before welding .99.4.2 Welded mesh which is zinc or zinc alloy coated after welding 99.4.3 Hot dip zinc or zinc alloy coating by a batch process (panels) 99.4.4 Coated with organic material after fabrication .910 Packaging .9Annex A (normative) Weld shear strength test method (welded mesh) . 10C

16、opyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (E) 3 Foreword This document (EN 10223-4:2012) has been prepared by Technical Committee ECISS/TC

17、106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest b

18、y May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10223-4:1998. EN 10223 “Steel wire and wire pr

19、oducts for fencing and netting“ consists of the following parts: Part 1: Zinc and zinc-alloy coated steel barbed wire Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes Part 3: Hexagonal steel wire mesh products for engineering purposes Part 4: Steel wire welded m

20、esh fencing Part 5: Steel wire woven hinged joint and knotted mesh fencing Part 6: Steel wire chain link fencing Part 7: Steel wire welded panels for fencing Part 8: Welded mesh gabion products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following c

21、ountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

22、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10

23、223-4:2012 (E) 4 1 Scope This European Standard specifies requirements for steel wire welded mesh fencing of which there are many types for a variety of applications. It specifies the general characteristics of welded mesh fencing supplied as rolls or panels and coatings, properties and tolerances.

24、This European Standard covers only orthogonal welded mesh i.e. wire welded at right angles to one another. For welded mesh fencing made from panels the specification covers only panels made from wires not greater than 10 mm. 2 Normative references The following documents, in whole or in part, are no

25、rmatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel p

26、roducts EN 10204, Metallic products Types of inspection documents EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10218-2:2012, Steel wire and wire products General Part 2: Wire dimensions and tolerances EN 10244-1, Steel wire and wire products Non-ferrous metallic coatings

27、on steel wire Part 1: General principles EN 10244-2:2009, Steel wire and wire products - Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN 10245-1, Steel wire and wire products Organic coatings on steel wire Part 1: General rules EN 10245-2, Steel wire and wire produ

28、cts Organic coatings on steel wire Part 2: PVC finished wire EN 10245-3, Steel wire and wire products Organic coatings on steel wire Part 3: PE coated wire EN ISO 1461, Hot dip galvanized coatings on fabricated iron or steel articles Specifications and test methods (ISO 1461) 3 Terms and definitions

29、 For the purposes of this document, the following terms and definitions apply. 3.1 welded mesh fencing fencing made by electrical resistance welding either: a) zinc-coated or zinc alloy coated wires; or b) bright wires which are subsequently coated after welding either with zinc or zinc alloy Note 1

30、 to entry: In both cases, the wire may or may not be crimped. The welded mesh may or may not be subsequently coated with an organic material. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license f

31、rom IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (E) 5 3.2 spacing distance measured between leading edge and leading edge of wires (see Figure 1) 3.3 mesh size of welded mesh spacing of line wires followed by the spacing of cross wire e.g. for 50 mm line wire spacing and 25 mm cross wire spacing the m

32、esh size is 50 mm x 25 mm 3.4 line wires wires running in the longitudinal direction parallel with the length of the roll or panel (see Figure 1) 3.5 cross wires wires running in the transverse direction (see Figure 1) Note 1 to entry: On erection of the fence, the cross wires become vertical. 3.6 p

33、anel welded mesh produced in flat form to specified dimensions or cut from rolls of welded mesh Note 1 to entry: Panels are produced either with overhanging edges or with flush cut edges Key 1 cross wires 2 line wire spacing 3 cross wire spacing 4 line wires Figure 1 Example of mesh Copyright Europe

34、an Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (E) 6 4 Information to be supplied by the purchaser The following information shall be supplied by the purchaser

35、 at the time of enquiry and order: a) number of this European Standard; b) quantity and packaging; c) if for agricultural use or not; d) roll or panel; e) mesh size(s); f) diameters of line and cross wires; g) length and width of rolls or size of panels; h) the class of zinc or zinc/alloy coating an

36、d whether applied before or after manufacture and if required, the adherence and assessment of adherence (wrap specification); i) whether an organic material coating is required and, if so, the type and colour; j) tensile strength of line wires and cross wires if different from each other; k) whethe

37、r or not crimping is required in line or cross wires; l) if applicable, the number of apertures required; m) in the case of panels, whether to be produced with overhangs or cut flush; n) test report requirements; o) agreed quality characteristics for testing (see Clause 7). 5 Manufacture 5.1 Base me

38、tal The base metal of the welded mesh fencing shall be low carbon steel. 5.2 Fabrication 5.2.1 Rolls The welded mesh fencing in roll shall be fabricated by electrical resistance welding either from: a) bright wires which subsequently after welding are either zinc or zinc alloy coated to EN 10244-1 a

39、nd EN 10244-2:2009, class A; or b) zinc or zinc alloy wire coated to EN 10244-1 and EN 10244-2:2009, class A, unless otherwise agreed at the time of enquiry and order. Where requested by the purchaser the welded mesh fencing shall be subsequently coated with an organic material to EN 10245-1 and EN

40、10245-2 or EN 10245-3. The type and colour and any other criteria shall be given on the order. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (

41、E) 7 5.2.2 Panels Panels shall be produced by either: a) cutting from zinc or zinc alloy coated rolls; or b) by electrical resistance welded bright wires and subsequently zinc or zinc alloy coated to EN ISO 1461. No bare patches shall be permitted. When requested by the purchaser the welded mesh fen

42、cing shall be subsequently coated with an organic material to EN 10245-1 and EN 10245-2 or EN 10245-3. The type and colour and any other criteria shall be given on the order. 5.3 Welding The mesh shall be produced by electrical resistance welding at every line wire/cross wire intersection. The line

43、and/or cross wires may be crimped. Depending on the application, the mesh spacing throughout the fencing may be the same, as in 50 mm x 50 mm security mesh or varying as in the welded mesh fencing for agricultural or general use i.e. decreasing mesh size from the top downwards. The diameter of line

44、wires may be different from the diameter of cross wires. 6 Requirements 6.1 Tensile strength The tensile strength of the line and cross wires shall be in the range 350 N/mm2 to 950 N/mm2. For any delivered lot, the spread of tensile strength shall be within 200 N/m2. NOTE The tensile strength of the

45、 line wires may not be the same as the tensile strength of the cross wires. 6.2 Tolerance on wire diameters The tolerance in diameter of the wires shall comply with the following grades from EN 10218-2. a) zinc or zinc alloy coated wire to EN 10244-2:2009, class A, tolerance shall be to EN 10218-2:2

46、012, T1 (Table 1). b) other zinc or zinc alloy coated wire, tolerance shall be to EN 10218-2:2012, T2 (Table 1). c) bright wire, tolerance shall be to EN 10218-2:2012, T3 (Table 1). d) wire coated with an organic material, tolerance shall be to EN 10218-2:2012 (Table 2). 6.3 Coatings 6.3.1 Zinc and

47、zinc alloy coatings 6.3.1.1 Rolls When coating applies to EN 10244-2:2009, class A, samples taken from the fence shall have the minimum coating mass requirement reduced by 5 % and where specified the number of dips shall be reduced by one half minute dip. Copyright European Committee for Standardiza

48、tion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10223-4:2012EN 10223-4:2012 (E) 8 Additionally, the adherence and wrapping requirements shall be as agreed at the time of enquiry and order. 6.3.1.2 Panels Where panels have been cut from zinc or zinc alloy coated rolls, the coated wire shall comply with the requirements of 6.3.1.1. Where panels have been produced by zinc or zinc alloy coating after fabrication the coate