DLA MS25165 REV F-2010 KNOB POINTER ILLUMINATED SMALL (ASG).pdf

《DLA MS25165 REV F-2010 KNOB POINTER ILLUMINATED SMALL (ASG).pdf》由会员分享，可在线阅读，更多相关《DLA MS25165 REV F-2010 KNOB POINTER ILLUMINATED SMALL (ASG).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5355 MS25165F 2 December 2010 SUPERSEDING MS25165E 17 June 1975 DETAIL SPECIFICATION SHEET KNOB, POINTER, ILLUMINATED, SMALL (ASG) This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product descri

2、bed herein shall consist of this specification sheet and procurement specification NASM25049. B (D FLAT)1.250.812.50055SET SCREW.500R .06245455.250A ABB.040WHITE ARROW4522 30.062.188.812.719.625.312.620 MAX.531.160B(D FLAT)SECTION A - A.062 X 45METALINSERTA.380SECTION B - BFIGURE I. Knob. INCH-POUND

3、Inactive for new design after 23 July 1997.INCHES MM.001 .016 .040 .062 .107 .125 .127 .160 .164 .188 .223 .250 .253 .312 .380 .500 .531 .620 .625 .719 .812 1.250 0.03 0.41 1.02 1.57 2.72 3.18 3.23 4.06 4.17 4.78 5.58 6.35 6.43 7.92 9.65 12.70 13.49 15.75 15.88 18.26 20.62 31.75 Provided by IHSNot f

4、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25165F 2TABLE I. Part Numbers and Dimensions. MIL - PART NUMBER B .001 A .001 SHAFT SIZE COLOR MS25165-1 .223 .253 .250 GRAY MS25165-2 .107 .127 .125 GRAY MS25165-3 .223 .253 .250 BLACK MS25165-4 .107 .127 .125 BLACK Not

5、es: 1 Dimensions are in inches. 2 Unless otherwise specified, tolerance is .016 (.41 mm), angle 2 0. 3 Metric equivalents (to the nearest .01 mm) are given on figure 1 for general information only and are based upon 1 inch = 25.4 mm. 4 For design feature purposes, this standard takes precedence over

6、 procurement documents referenced herein. 5 Referenced documents shall be of the issue in effect on the date of invitation for bid. 6 Material: Knob, transparent thermoplastic. Insert, brass per ASTM B36/36M. Setscrew, CRES per SAE-AMS-S-7720. 7 Finish: Knob, grey or black color number 36231 or 3703

7、8 per FED-STD-595. Index line, white color number 37875 per FED-STD-595. Insert, nickel plate per SAE-AMS-QQ-N-290, bright finish, Class 2, Grade G. 8 Percent transmittance 12.0 3%. 9 There shall be no light leak around the setscrew. 10 Bottom surface of the knob shall be polished. 11 All outside co

8、rners and inside fillets shall have a .04 (1.02 mm) radius. 12 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted w

9、ithout license from IHS-,-,-MS25165F 3Custodians: Preparing Activity: Army -CR DLA -IS Navy - AS Air Force 11 (Project 5355-2010-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-