DLA MS24697 REV A-2005 RETAINER CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组连接器止动装置》.pdf

《DLA MS24697 REV A-2005 RETAINER CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组连接器止动装置》.pdf》由会员分享，可在线阅读，更多相关《DLA MS24697 REV A-2005 RETAINER CONNECTOR RACK AND PANEL MINIATURE《微型机架和小组连接器止动装置》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMS24697A 14 July 2005 SUPERSEDING MS24697 13 October 1960 DETAIL SPECIFICATION SHEET RETAINER, CONNECTOR, RACK AND PANEL, MINIATURE Inactive for new design after 8 June 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requiremen

2、ts for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26518. The Qualified Products List (QPL) associated with this inactive for new design specification will be maintained until acquisition of the product is no longer required, where upon the specificat

3、ion and QPL will be canceled. NOTES: 1. All dimensions in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified tolerances are .005 inches (0.13 mm). FIGURE 1. Spring loaded mounting assembly. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproductio

4、n or networking permitted without license from IHS-,-,-MS24697A 2 REQUIREMENTS: Dimensions and configuration see figure 1. Material: Stainless steel spring wire type 631 in accordance with ASTM A313 UNS designator S17700. No permanent set allowable at solid length, spring must withstand 260C (500F)

5、continuously. Part or identifying number (PIN): MS PIN Total coils Active coils I.D. +.010 (inches)Wire Dia. (inches)Approximate free length (inches) Spring rate per inch LBS load at .550 inch MS24697-1 8 6 .233 .047 .755 47 lbs 9.9 5% MS24697-2 10 8 .230 .040 .875 23 lbs 7.6 5% MS24697-3 11 9 .235

6、.035 .945 12 lbs 4.8 5% Part or identifying number (PIN) (metric): 1/ MS PIN Total coils Active coils I.D. +0.25 (mm) Wire Dia. (mm) Approximate free length (mm) Spring rate per 25.4 mm kg load at 13.97 mm MS24697-1 8 6 5.92 1.19 19.17 21.32 kg 4.49 5% MS24697-2 10 8 5.84 1.02 22.23 10.43 kg 3.45 5%

7、 MS24697-3 11 9 5.97 0.89 24.00 5.44 kg 2.18 5% 1/ Metric equivalents are given for general information only. Referenced documents: In addition to MIL-DTL-26518 this document references the following: ASTM A313 Changes from previous issue. Marginal notations are not used in this revision to identify

8、 changes with respect to the previous issue due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 11 DLA - CC DLA - CC (Project 5935-4704-000) Review activities: DLA - IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-