ASTM F256-2005(2010) Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium《含有18%或26%铬的铬铁密封合金的标准规范》.pdf

《ASTM F256-2005(2010) Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium《含有18%或26%铬的铬铁密封合金的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F256-2005(2010) Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium《含有18%或26%铬的铬铁密封合金的标准规范》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F256 05 (Reapproved 2010)Standard Specification forChromium-Iron Sealing Alloys with 18 or 28 PercentChromium1This standard is issued under the fixed designation F256; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers two chromium-iron alloys, theformer, (UNS K91800), nominally 18 % chromium, balanc

3、eiron, the latter, (UNS K92801), nominally 28 % chromium, instrip, bar, wire, and rod forms intended primarily for sealing toglass in electronic applications.NOTE 1UNS K92801 should only be considered for use at servicetemperatures below 300C. The alloy is prone to sigma phase formation attemperatur

4、es close to 620C, and exhibits brittle mechanical behaviorafter prolonged exposures at temperatures close to 475C.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand

5、 are not considered standard.1.3 The following hazard caveat pertains only to the testmethod portion, Sections 16 and 17, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard t

6、o establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsE3 Guide for Preparation of Metallographic SpecimensE18 Test

7、Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron AlloysE228 Test Method for Linear Thermal Expansion of SolidMaterials Wit

8、h a Push-Rod DilatometerF14 Practice for Making and Testing Reference Glass-MetalBead-SealF140 Practice for Making Reference Glass-Metal Butt Sealsand Testing for Expansion Characteristics by PolarimetricMethodsF144 Practice for Making Reference Glass-Metal SandwichSeal and Testing for Expansion Cha

9、racteristics by Polari-metric Methods3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bar:3.1.1.1 hot-finished rounds, squares, and hexagons,14 in.(6.4 mm) and over in diameter or size.3.1.1.2 hot-finished flats,14 in. to 10 in. (6.4 to 254 mm),inclusive, in width and18 in. (3.

10、2 mm) and over in thickness.3.1.1.3 cold-finished rounds, squares, octagons, hexagonsand shapes, over12 in. (12.7 mm) in diameter or size.3.1.1.4 cold-finished flats,38 in. (9.5 mm) and over in widthand18 in. (3.2 mm) and over in thickness (see Discussions).DiscussionWidths less than38 in. (9.5 mm)

11、and thick-nesses less than316 in. (4.8 mm) are generally described as flatwire.DiscussionThicknesses of18 in. (3.2 mm) to under316 in.(4.8 mm) can also be described as cold-rolled strip or, if in cutlengths, bar.3.1.2 rodhot-rolled, or hot-rolled, annealed, and pickled,rounds, squares, octagons, hex

12、agons and shapes, in coils, forsubsequent cold drawing or cold rolling,14 in. or34 in. (6.4 or19.0 mm) in diameter or size.3.1.3 stripcold-finished coils or cut lengths, under 24 in.(610 mm) down to and including316 in. (4.8 mm) in width, andunder316 in. down to and including 0.005 in. (0.13 mm) int

13、hickness.3.1.4 No. 1 edgea rolled edge either round or square asspecified.1This specification is under the jurisdiction of ASTM Committee F01 onElectronics and is the direct responsibility of Subcommittee F01.03 on MetallicMaterials.Current edition approved Oct. 1, 2010. Published November 2010. Ori

14、ginallyapproved in 1951 as F256 51 T. Last previous edition approved in 2005 asF256 94 (2005)1. Consolidated with F257 in 1972. DOI: 10.1520/F0256-05R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSt

15、andards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.5 No. 3 edgean edge produced by slitting.3.1.6 No. 5 edgean approximately square edge pro

16、ducedby rolling or filing after slitting.DiscussionCold-finished product 0.005 in. (0.13 mm) inthickness and under 24 in. (609.6 mm) in width is sometimesidentified as foil.3.1.7 wire:3.1.7.1 cold finished only, round or square,12 in. (12.7 mm)and under in diameter or size.3.1.7.2 cold finished only

17、, flat wire of116 in. (1.6 mm) tounder38 in. (9.5 mm) in width and 0.010 in. (0.25 mm) tounder316 in. (4.8 mm) in thickness.4. Classification4.1 The alloys covered by this specification are classified bynominal chemical composition, specifically by chromium con-tent, in two types:4.1.1 Type I18 % ch

18、romium (UNS K91800) and4.1.2 Type II28 % chromium (UNS K92801).5. Ordering Information5.1 Orders for material under this specification shall includethe following information:5.1.1 Quantity (weight (Note 2) or number of pieces),5.1.2 Name of material (chromium-iron alloy),5.1.3 Type (Section 4),5.1.4

19、 Form (Section 3),5.1.5 Temper and finish (Section 7),5.1.6 Permissible variations in dimensions for rod (Section13),5.1.7 Certification if required (Section 21),5.1.8 Packaging required (Section 22),5.1.9 Dimensions (width, thickness, diameter, etc.),5.1.10 ASTM designation: F256, and5.1.11 Excepti

20、ons to the specification or special require-ments.NOTE 2The term “weight” is temporarily used in this standardbecause of established trade usage. The word is used to mean both “force”and“ mass,” and care must be taken to determine which is meant in eachcase (SI unit for force = newton and for mass =

21、 kilogram).5.2 If possible, the intended end use of the item should begiven on the purchase order especially when the item is orderedfor a specific end use or uses. Such information will enable themanufacturer to produce a material more satisfactory for thepurchasers process and product.NOTE 3A typi

22、cal ordering description is as follows: 2000 kg,chromium-iron alloy. Type II, wire, annealed, cold drawn, commercialpackaging,14 in. (6.4 mm) round by coil, ASTM F256, end use-redraw.6. Process6.1 The purchaser shall specify that the alloy be made byone or more of the following processes: electric-a

23、rc, electric-induction, or other process approved by the purchaser.7. Temper and Finish7.1 The desired temper of the material shall be specified onthe purchase order as follows:7.1.1 Annealed for forming (strip),7.1.2 Annealed for deep drawing (strip),7.1.3 Cold rolled or cold drawn to a specified m

24、echanicalproperty level, or7.1.4 As hot rolled.7.2 The desired surface of the material shall be specified onthe purchase order as follows:7.2.1 Pickled,7.2.2 Cold drawn (wire and bar),7.2.3 Centerless ground (wire and bar), or7.2.4 Cold rolled (strip).8. Chemical Composition8.1 The material shall co

25、nform to the chemical compositionspecified in Table 1.8.2 Ladle AnalysisA ladle analysis of each heat of steelshall be made by the manufacturer to determine the percent-ages of the elements specified in Table 1. The analysis shall bemade from test castings made during the pouring of the heat.The che

26、mical composition thus determined shall conform tothe requirements specified in Table 1.8.3 Check AnalysisIf check analysis is made by thepurchaser, the chemical composition thus determined shallconform to the requirements specified in Table 1 subject to thepermissible tolerances of Table 2.9. Chemi

27、cal Analysis9.1 Chemical analysis shall be made in accordance withMethod E38 or equivalent methods.TABLE 1 Chemical RequirementsNOTE 1Round observed or calculated values to the nearest unit in thelast right-hand place of figures used in expressing the limiting value, inaccordance with the rounding-o

28、ff method of Practice E29.ElementComposition, %Type I Type IICarbon, max 0.08 0.12Manganese, max 1.00 1.00Silicon, max 0.75 0.75Phosphorus, max 0.040 0.040Sulfur, max 0.030 0.030Chromium, nominal 18.0 28.0Nickel, max 0.50 0.50Nitrogen, max . 0.20TitaniumA.Iron remainder remainderAFive times the carb

29、on content, minimum, and 0.60, max.TABLE 2 Check Analysis TolerancesTolerances over maxi-Element mum or under minimumlimits, percentage pointsCarbon 0.01Manganese 0.03Phosphorus 0.005Sulfur 0.005Silicon 0.05Nickel 0.03Nitrogen 0.01Titanium 0.05F256 05 (2010)210. Thermal Expansion Requirements Therma

30、l ExpansionRequirements10.1 The material shall conform to the thermal expansionrequirements prescribed in Table 3.11. Mechanical Property Requirements11.1 The material shall conform to the mechanical propertyrequirements prescribed in Table 4. Rockwell hardness shall bedetermined in accordance with

31、Test Method E18.12. Transformation Requirements12.1 The material shall show no evidence of transformationto martensite. For Type I alloy, the austenite formed duringheat treating will transform to martensite at or above roomtemperature. The presence of austenite, as may be noted inType II alloy, is

32、acceptable if the thermal expansion require-ment is met.13. Permissible Variations in Dimensions13.1 Material furnished under this specification, except rod,shall conform to the dimensional requirements of Tables 5-15.13.2 Permissible variations in dimensions for rod for re-drawing or rerolling shal

33、l be as agreed upon between purchaserand manufacturer.14. Workmanship, Finish, and Appearance14.1 The material shall be commercially smooth and uni-form in cross section, composition, and temper; it shall be freeof scale corrosion, cracks, seams, scratches, slivers, processinglubricants, and other d

34、efects as best commercial practice willpermit.15. Number of Tests and Retests15.1 Test specimens for thermal expansion and phase-transformation requirements shall be selected on the basis of aminimum of one specimen per heat.15.2 Test specimens for mechanical properties shall beselected on the basis

35、 of a minimum of one specimen per size,each heat, each lot annealed or otherwise heat treated under thesame conditions, and each lot with like processing.15.3 If any test specimen shows defective machining ordevelops flaws, it may be discarded and another specimensubstituted.15.4 If the results of a

36、ny test lot are not in conformance withthe requirements of this specification, such lots may beretreated at the option of the manufacturer. The material shallbe acceptable if the results of tests on the retreated material arewithin the requirements of this specification.16. Specimen Heat Treatment16

37、.1 The specimens for thermal-expansion and phase-transformation tests shall be heat treated prior to testing asfollows:16.1.1 Type IHeat the specimen to 1200 6 10C and holdat temperature for 15 min. Air cool to room temperature.16.1.2 Type IIHeat the specimen to 1100 6 10C andhold at temperature for

38、 15 min. Air cool to room temperature.The cooling rate is recommended to be faster than 300C perhour between 600 and 300C. Slower cooling rates could leadto brittle mechanical behavior.TABLE 3 Thermal Expansion RequirementsA,BTemperatureRange, CMean Coefficient of Linear ThermalExpansion, m/m CUNS K

39、91800 UNS K9280130 to 530 11.3 to 11.7 10.8 to 11.4ATypical thermal expansion data for the alloys covered by this specification aregiven for information only in the Appendix.BThese requirements apply to specimens heat treated prior to test in accordancewith Section 16.TABLE 4 Mechanical Property Req

40、uirementsAThickness, in. (mm)RockwellHardness (orequivalent)(max)Tensile Strength,max.ksi MPaUnder 0.015 (0.38) . 85 5900.015 (0.38) to 1 (25.4), incl B85 . .Over 1 (25.4) B88 . .AApplicable to strip in the annealed condition only. All other mechanicalproperties as agreed upon between purchaser and

41、manufacturer.TABLE 5 Permissible Variations in Size of Cold-Finished RoundBarsSpecified Size, in.(mm)Permissible Variations from SpecifiedSize, in. (mm)A,BOver UnderOver12 (12.7) to 1(25.4), excl0.002 (0.05) 0.002 (0.05)1 (25.4) to 112 (38.1),excl0.0025 (0.064) 0.0025 (0.064)112 (38.1) to 4 (101.6),

42、inclC0.003 (0.08) 0.003 (0.08)AUnless otherwise specified, size tolerances are over and under as shown inthe above table. When required, however, they may be specified all over andnothing under, or all under and nothing over, or any combination of over and under,if the total spread in size tolerance

43、 for a specified size is not less than the totalspread shown in the table.BWhen it is necessary to heat treat or heat treat and pickle after cold finishing,size tolerances are double those shown in the table.CCold-finished bars over 4 in. (101.6 mm) in diameter are produced; sizetolerances for such

44、bars have not been evolved.TABLE 6 Permissible Variations in Length of Hot-Finished orCold-Finished BarsASpecified Size ofRounds, Squares,Hexagons, Octagons,and Widths of Flats,in. (mm)BPermissible Variations in Length, in.(mm)For Lengths up to12 ft (3.7 m), inclFor Lengths over12 ft (3.7 m), to 25

45、ft(7.6 m), inclOver Under Over UnderTo 2 (50.8), incl12 (12.7) 034 (19.0) 0Over 2 (50.8) to 4 (101.6), incl34 (19.0) 0 1 (25) 0Over 4 (101.6) to 6 (152.4), incl 1 (25) 0 114 (32) 0Over 6 (152.4) to 9 (228.6), incl 114 (32) 0 112 (38) 0Over 9 (228.6) to 12 (304.8), incl 112 (38) 0 2 (51) 0AThe order

46、should specify random lengths or specific lengths. When randomlengths are ordered, the length tolerance is not less than 2 ft (609.6 mm). Whenspecific lengths are ordered, Table 8 or Table 9 shall apply.BThe maximum width of bar flats is 10 in. (254.0 mm).F256 05 (2010)317. Test Methods17.1 Thermal

47、Expansion (Note 4)After heat treatment ofthe specimen in accordance with Section 16, determine thethermal expansion characteristics in accordance with TestMethod E228.NOTE 4Although not required, the thermal expansion match betweenthe alloy and a glass may be evaluated by preparing and testing anass

48、embly in accordance with Practices F14, F140,orF144.17.2 TransformationCut the specimen from any part ofthe material, preferably including the entire cross section,degrease it, and then heat treat it as described in Section 16.When cool, polish the cross section of the specimen and etch inaccordance

49、 with Methods E3 (Note 5). Examine the specimenat a magnification of 1503 for the presence of the acicularcrystals of the martensite phase. Because these crystals mayoccur only in small localized areas, examine carefully theentire polished cross section.NOTE 5A suggested etchant is a solution of 3 parts by volume ofconcentrated hydrochloric acid and 1 part by volume of concentrated nitricacid saturated with cupric chloride (CuCl22H2O). This etchant is moreeffective when allowed to stand for 20 min after mixing. Aft