ASTM E2195-2002e1 Standard Terminology Relating to the Examination of Questioned Documents《与咨询文件检验相关的标准术语》.pdf

《ASTM E2195-2002e1 Standard Terminology Relating to the Examination of Questioned Documents《与咨询文件检验相关的标准术语》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2195-2002e1 Standard Terminology Relating to the Examination of Questioned Documents《与咨询文件检验相关的标准术语》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 2195 02e1Standard Terminology Relating to theExamination of Questioned Documents1This standard is issued under the fixed designation E 2195; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEThe definition for ascender was corrected editorially in July 2003.1. Scope1.1 This terminology standard includes terms that relate tothe

3、examination performed by forensic document examiners.NOTE 1The terms in the Terminology Section refer to typical copy-book styles of writing and do not account for exceptional forms.2. Referenced Documents2.1 ASTM Standards:E 444 Scope of Work Relating to Forensic Document Ex-aminers23. Terminologya

4、pex, nthe uppermost point of a character.ascender, na stroke that rises above the height of the body ofthe letter formation.assisted hand signature, na signature executed by a writerwhile the writers hand, arm, or writing instrument issteadied or stabilized by another.awkward hand, nsee unaccustomed

5、 hand.baseline , nthe ruled or imaginary line upon which writingor typewriting appears to rest.character, nany language symbol (for example, letter, nu-meral, punctuation mark, or other sign), other symbol orornament.connecting stroke, na line joining two adjacent characters.cross stroke, na stroke

6、that crosses another portion of thecharacter and is not attached at either end. (For example, thehorizontal stroke of the “t”) (cf. crossbar).crossbar, na stroke that intersects other portions of thecharacter at both ends. (cf. arm and cross stroke).cursive, na type of writing in which the letters a

7、re joined andthe writing instrument is not lifted after most strokes.descender, na stroke that extends below the baseline of thebody of the letter formationdrag stroke, na stroke resulting from incomplete lifting ofthe pen.guided signature, na signature executed by a writer while awriters hand arm,

8、or writing instrument is influenced orcontrolled by another.hand printing, na style of writing in which the letters arenot joined and the writing instrument is lifted after moststrokes.hesitation, na pause in the writing without the instrumentbeing lifted.individualizing characteristic, nmarks or pr

9、operties thatserve to individualize writing.indentations, nlatent or visible impressions in paper or othermedia.line quality, nthe sum total of the attributes of the writingmovement (for example, speed, pressure, and skill).loop, na formation that curves and crosses itself.manuscript, nsee handprint

10、ing.model signature, na signature that is used as a prototype fora simulation or copy, by manual electronic or other means.patching, nretouching a portion of a written stroke.pen lift, nan interruption in a stroke caused by removing thewriting document from the writing surface.pen position, nthe rel

11、ationship between the writing instru-ment and the writing surface.pen pressure, nthe force with which the writing instrumentcontacts the paper.retrace, na stroke written back over the preceding stroke inthe reverse direction.1This terminology standard is under the jurisdiction of ASTM Committee E30o

12、n Forensic Sciences and is the direct responsibility of Subcommittee E30.02 onQuestioned Documents.Current edition approved April 10, 2002. Published July 2002.2Annual Book of ASTM Standards, Vol 14.02.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-295

13、9, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of

14、 such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for a

15、dditional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to

16、 the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E219502e12