ASTM D7050-2004(2014) 8362 Standard Practice for Rubber from Natural SourcesSampling and Sorting Bales Based on Predicted Processing Properties《天然橡胶以及基于预测加工性能的取样和分类包的标准实施规程》.pdf

《ASTM D7050-2004(2014) 8362 Standard Practice for Rubber from Natural SourcesSampling and Sorting Bales Based on Predicted Processing Properties《天然橡胶以及基于预测加工性能的取样和分类包的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7050-2004(2014) 8362 Standard Practice for Rubber from Natural SourcesSampling and Sorting Bales Based on Predicted Processing Properties《天然橡胶以及基于预测加工性能的取样和分类包的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7050 04 (Reapproved 2014)Standard Practice forRubber from Natural SourcesSampling and Sorting BalesBased on Predicted Processing Properties1This standard is issued under the fixed designation D7050; the number immediately following the designation indicates the year oforiginal adoption

2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the sorting of natural rubber balesof TSR10 or TSR20 in

3、 the factory according to their predictedprocessing performance based on differences in viscoelasticproperties.1.2 This practice determines which bales should be used infactory compounds which benefit from using “soft” naturalrubber versus which work better with “hard” natural rubber.2. Referenced D

4、ocuments2.1 ASTM Standards:2D1485 Practice for Rubber from Natural SourcesSampling and Sample PreparationD2227 Specification for Natural Rubber (NR) TechnicalGradesD3194 Test Method for Rubber From Natural SourcesPlasticity Retention Index (PRI)D6204 Test Method for RubberMeasurement of Unvulca-nize

5、d Rheological Properties Using Rotorless Shear Rhe-ometers3. Significance and Use3.1 In accordance with Specification D2227, shipments ofTSR10 and TSR20 must meet a minimum initial Wallaceplasticity (Po) of 30 to be accepted. However, even with thisminimum restriction, the uncured viscoelastic or “p

6、rocessabil-ity” properties are allowed to vary greatly. This variation inproperties can significantly affect the quality and efficiency ofa factory operation.3.2 Bales of TSR10 or TSR20 which are lower in theiruncured elastic quality (“soft” rubber) in some cases mayimpart better processing properti

7、es to tire innerliners, cushiongums, and sidewalls. “Soft” bales sometimes impart betterbuilding tack, better mold flow, and lower extrusion die swellwith better dimensional stability. Also, these “soft” rubberbales may dissolve faster in solvents for adhesion dipping.3.3 Bales of TSR10 or TSR20 tha

8、t are higher in theiruncured elastic quality (“hard” rubber) in some cases generategreater shearing during the initial stages of a factory mix,which result in a faster breakdown and a shorter mix cycle.3.4 Therefore, in a factory operation, sometimes segregatingTSR10 or TSR20 shipments into “soft” a

9、nd “hard” categoriescan improve the efficiency and quality of a factory operation.4. Sampling4.1 Sample SizeThe number of samples to be selected torepresent the lot may be determined by the size of the lot asindicated in Practice D1485, Table 1.4.2 Alternatively, five bales from a 36-bale pallet may

10、 besampled.4.3 Samples from these bales should be taken from withinthe bale, not from the edges, because bale surface exposure tothe air will cause surface samples to not be representative ofthe rubber inside the bale.5. Lot Sorting5.1 The criteria for sorting should be based on a repeatablemeasure

11、of uncured elasticity of the raw natural rubber.5.2 Measuring uncured elastic modulus G at 1 Hz, 100 %strain, 100C in accordance with Test Method D6204, Part B,has been found to be an effective method for segregating “soft”natural rubber from “hard” natural rubber used in production.See also Test Me

12、thod D3194.5.3 The segregating elastic modulus value GSEGis estab-lished as the criteria for separating “soft” natural rubber from“hard” natural rubber as shown in Fig. 1.5.4 The value assigned to GSEGwill depend on the factorysetting. It will be dependent on the type of different compoundsbeing mix

13、ed. A value must be assigned that will provide thebest balance for quality and cost effectiveness for each pro-duction plant site.1This practice is under the jurisdiction of ASTM Committee D11 on Rubber andis the direct responsibility of Subcommittee D11.22 on Natural Rubber.Current edition approved

14、 May 1, 2014. Published May 2014. Originallyapproved in 2004. Last previous edition approved in 2009 as D7050 04 (2009).DOI: 10.1520/D7050-04R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards

15、volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. Keywords6.1 hard rubber; natural rubber; processability; processingproperties; sampling; soft rubbe

16、r; sorting balesASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of

17、such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for ad

18、ditional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to

19、the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at t

20、he aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. 1 Segregating Raw Natural Rubber Shipments of TSR10 or TSR20 for Factory ProductionD7050 04 (2014)2