ASTM D3678-1997(2001) Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯内定形挤压件标准规范》.pdf

《ASTM D3678-1997(2001) Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯内定形挤压件标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3678-1997(2001) Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯内定形挤压件标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3678 97 (Reapproved 2001)An American National StandardStandard Specification forRigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions1This standard is issued under the fixed designation D 3678; the number immediately following the designation indicates the year oforiginal adopt

2、ion or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope *1.1 This specification establishes requirements for the ma-terial properti

3、es, including dimensional stability and extrusionquality, of rigid, poly(vinyl chloride) (PVC) interior-profileextrusions. Methods for identifying interior-profile extrusionsthat comply with the requirements of this specification areprovided.1.2 Rigid PVC recycled plastic may be used in this product

4、in accordance with the requirements in Sections 6 and 7.1.3 Rigid PVC compounds for interior building productapplications are covered in Specification D 1784.1.4 Rigid PVC exterior profile extrusions for assembledwindows and doors are covered in Specification D 4726.1.5 The text of this standard ref

5、erences notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in Tables and Figures) shall not be consideredas requirements of this standard.1.6 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are given forin

6、formation only.NOTE 1Information with regard to application should be obtainedfrom the manufacturers of the profiles.NOTE 2There are no ISO standards covering the primary subjectmatter in this specification.1.7 The following precautionary caveat pertains only to thetest method portion, Section 8, of

7、 this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2

8、. Referenced Documents2.1 ASTM Standards:D 618 Practice for Conditioning Plastics and for Testing2D 696 Test Method for Coefficient of Linear ThermalExpansion of Plastics Between -30C and 30C with avitreous Silica Dilatometer2D 883 Terminology Relating to Plastics2D 1042 Test Method for Linear Dimen

9、sional Changes ofPlastics Under Accelerated Service Conditions2D 1600 Terminology for Abbreviated Terms Relating toPlastics2D 1784 Specification for Rigid Poly(Vinyl) Chloride(PVC) Compounds and Chlorinated Poly (Vinyl Chloride)(CPVC) Compounds2D 2152 Test Method for Adequacy of Fusion of ExtrudedPo

10、ly(Vinyl Chloride) (PVC) Pipe and Molded Fittings byAcetone Immersion3D 3892 Practice for Packaging/Packing of Plastics4D 4726 Specification for White Rigid Poly (Vinyl Chloride)(PVC) Exterior Profile Extrusions Used for AssembledWindows and Doors3D 5033 Guide for the Development of ASTM StandardsRe

11、lating to Recycling and Use of Recycled Plastics5E 631 Terminology of Building Constructions63. Terminology3.1 GeneralDefintions are in accordance with Terminol-ogy D 883 or Terminology E 631 and abbreviations withTerminology D 1600, unless otherwise indicated.4. Significance and Use4.1 The purpose

12、of this specification is to establish on anational basis, a recognized standard of quality for rigidpoly(vinyl chloride) (PVC) interior-profile extrusions for inte-rior use other than cellular products, piping, tubing, andwindow and door profiles used in finished building products.The information co

13、ntained in this standard is intended to behelpful to producers, distributors, and users, and to promoteunderstanding between buyers and sellers. It is also intended toserve as the basis for requirements on finished interior building1This specification is under the jurisdiction of ASTM Committee D20

14、onPlastics, and is the direct responsibility of Subcommittee D20.24 on Plastic BuildingProducts.Current edition approved July 10, 1997. Published November 1997. Originallypublished as D 3678 78. Last previous edition D 3678 96.2Annual Book of ASTM Standards, Vol 08.01.3Annual Book of ASTM Standards,

15、 Vol 08.04.4Annual Book of ASTM Standards, Vol 08.02.5Annual Book of ASTM Standards, Vol 08.03.6Annual Book of ASTM Standards, Vol 04.11.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-29

16、59, United States.products which are either made from or employ rigid PVCprofile extrusions in their construction.5. Classification5.1 This standard covers three classes of rigid PVC interior-profile extrusions as follows:Class 1Normal impactClass 2Intermediate impactClass 3High impact6. Materials a

17、nd Manufacture6.1 This specification covers profile extrusions made fromplastics conforming to the requirements of SpecificationD 1784. Class 1 extrusions shall meet the requirements speci-fied in Specification D 1784 for Class 12454 compound. Class2 extrusions shall meet the requirements for Class

18、14323compound. Class 3 extrusions shall meet the requirements forClass 1-40031-54-0000 compound. Refer to Table 1 in Speci-fication D 1784.6.2 Rigid PVC recycled plastic, as defined in Guide D 5033,may be used in this product if all the requirements in thesections on Materials and Manufacture (Secti

19、on 6), and onPhysical Requirements (Section 7) are met by the extrusionscontaining PVC recycled plastic.6.3 All Class compounds shall have a minimum coefficientof linear expansion of 10 3 10-5cm/cm/C (5.5 3 10-5in./in./F).NOTE 3Non-PVC materials may be used as a capstock.6.4 Rework MaterialClean, ho

20、mogeneous PVC reworkmaterial or rework material containing PVC capstock gener-ated from the manufacturers own production of the same classcompound may be used by the same manufacturer providingthat the extruded profiles meet all the requirements of thisspecification. Clean principally PVC rework mat

21、erial contain-ing non-PVC capstock may be used only in the substrate of acapstocked product by the same manufacturer, providing thatthe extruded profiles meet all of the requirements of thisspecification.6.5 The PVC compound in extruded section shall maintainuniform color and be free of any visual s

22、urface or structuralchanges, such as peeling, chipping, cracking, flaking, orpitting.7. Physical Requirements7.1 DimensionsThe size, thickness, and dimensional tol-erances of the interior-profile extrusions shall be as agreedupon between the supplier and purchaser.7.2 Dimensional StabilityThe dimens

23、ional stability of theinterior-profile extrusions shall be determined in the extrusiondirection in accordance with 8.5. Extrusions over 1.02 mm(0.040 in.) in thickness shall have a maximum shrinkage of2.2 %; those of 1.02-mm (0.040-in.) thickness or less shallhave a 3.0 % maximum shrinkage.7.3 Extru

24、sion QualityThe extrusion quality of Class 1extrusions shall be determined by immersion in anhydrousacetone in accordance with the requirements of 8.6. Specimensof extrusions having not more than 25 % surface attack shall beconsidered as adequately fused and of satisfactory quality. Theextrusion qua

25、lities of Class 2 and Class 3 extrusions shall be asagreed upon between the supplier and purchaser.8. Test Methods8.1 GeneralUse the inspection and test procedures con-tained in this section to determine the conformance of productsto the requirements of this specification. Each producer ordistributo

26、r who represents his products as conforming to thisspecification may utilize statistically based sampling plans thatare appropriate for each particular manufacturing process, butshall keep such essential records as are necessary to documentwith a high degree of assurance his claim that all of thereq

27、uirements of this specification have been met. Additionalsampling and testing of the product, as may be agreed uponbetween supplier and purchaser, is not precluded by thissection.8.2 Visual InspectionVisually examine the interior-profileextrusions to determine their compliance with the requirementso

28、f 6.5.8.3 Conditioning of SpecimensCondition the test speci-mens in accordance with Procedure A of Practice D 618, exceptthat the minimum conditioning time shall be 24 h.8.4 Test ConditionsConduct the tests the Standard Labo-ratory Atmosphere of 23 6 1C (73.4 6 2F) and 50 6 5%relative humidity, unle

29、ss otherwise specified in the applicabletest method.8.5 Dimensional StabilityDetermine the dimensional sta-bility in accordance with Test Method D 1042, except that thetest cycle shall consist of heating the specimens for 30 min ina uniformly heated oven at a temperature of 82 6 0.6C (1806 1F).8.6 E

30、xtrusion QualityDetermine the extrusion quality inaccordance with Test Method D 2152, except that the testspecimens shall be 25.40 to 50.80 mm (1 to 2 in.) in length andsufficient in number to ensure testing the complete crosssection. In the test procedure described, the interior-profileextrusions w

31、ill normally swell and soften in contact withanhydrous acetone. In some cases there may be surface attack.Disintegration is defined as complete separation of flakes orpieces from the body of the extrusion.8.7 Coeffcient of Linear ExpansionConduct this test inaccordance with Test Method D 696.9. Prod

32、uct Marking9.1 In order that purchasers may identify products conform-ing to all requirements of this specification, producers anddistributors may include a statement of compliance in conjunc-tion with their name and address on product labels, invoices,sales literature, and the like. The following s

33、tatement issuggested when sufficient space is available:“The product conforms to all of the requirements establishedin ASTM D 3678, developed cooperatively with the industryand published by ASTM.”“Full responsibility for the conformance of this product tothis specification is assumed by (name and ad

34、dress of produceror distributor).”9.2 The following abbreviated statement is suggested whenavailable space on labels is insufficient for the full statement:D 36782“Conforms to ASTM D 3678 (name and address of produceror distributors).”9.3 All packing, packaging, and marking provisions ofPractice D 3

35、892 shall apply to this specification.10. Packaging10.1 The interior-profile extrusions shall be packaged insuch a manner as to provide reasonable protection againstdamage in ordinary handling and transportation.11. Keywords11.1 building products; extrusion; interior profile extru-sions; recycled pl

36、astic; rigid poly(vinyl chloride)SUMMARY OF CHANGESCommittee D-20 has identified the location of the following changes to this standard since the last isse (D367896) that may impact the use of this standard.(1) Added reference to related standards in Scope.(2) Added paragraph 1.5 regarding notes.(3)

37、 Added coefficient of expansion requirement (6.3).(4) Added provision for rework and visual inspection require-ments (6.4 and 6.5).(5) Allowed non-PVC capstock (Note 3).ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin

38、this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must

39、 be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of ther

40、esponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 36783