ASTM B821-2010(2016) Standard Guide for Liquid Dispersion of Metal Powders and Related Compounds for Particle Size Analysis《粒度分析用金属粉末和相关化合物的液体分散标准指南》.pdf
《ASTM B821-2010(2016) Standard Guide for Liquid Dispersion of Metal Powders and Related Compounds for Particle Size Analysis《粒度分析用金属粉末和相关化合物的液体分散标准指南》.pdf》由会员分享,可在线阅读,更多相关《ASTM B821-2010(2016) Standard Guide for Liquid Dispersion of Metal Powders and Related Compounds for Particle Size Analysis《粒度分析用金属粉末和相关化合物的液体分散标准指南》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B821 10 (Reapproved 2016)Standard Guide forLiquid Dispersion of Metal Powders and RelatedCompounds for Particle Size Analysis1This standard is issued under the fixed designation B821; the number immediately following the designation indicates the year oforiginal adoption or, in the case
2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide covers the dispersion in liquids of metalpowders and related compounds for subseq
3、uent use in particlesize analysis instruments. This guide describes a generalprocedure for achieving and determining dispersion; it alsolists procedures that are currently in general use for certainmaterials.1.2 This guide is limited to metal powders and related metalcompounds. However, the general
4、procedure described hereinmay be used, with caution as to its significance, for otherparticulate materials, such as ceramics, pigments, minerals, etc.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.4 This standard
5、 does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM
6、Standards:2B243 Terminology of Powder MetallurgyB430 Test Method for Particle Size Distribution of Refrac-tory Metal Powders and Related Compounds by Turbidi-metryB761 Test Method for Particle Size Distribution of MetalPowders and Related Compounds by X-Ray Monitoringof Gravity SedimentationB822 Tes
7、t Method for Particle Size Distribution of MetalPowders and Related Compounds by Light Scattering3. Terminology3.1 DefinitionsDefinitions of powder metallurgy termscan be found in Terminology B243.4. Significance and Use4.1 The method of powder dispersion in a liquid has asignificant effect on the r
8、esults of a particle size distributionanalysis. The analysis will show a too-coarse, unstable, ornonrepeatable distribution if the powder has not been dispersedadequately. It is therefore important that parties wishing tocompare their analyses use the same dispersion technique.4.2 This guide provide
9、s established powder dispersion tech-niques for certain materials and the means of deriving tech-niques for materials not listed. It should be used by all partiesperforming liquid-dispersed particle size analysis of all of thematerials covered by this guide (see 1.1, 1.2, and 4.1).4.3 This guide sho
10、uld be used in the preparation of powdersfor use in Test Methods B430, B761, and B822 and otherprocedures that analyze metal powder particle size distribu-tions in liquid-dispersed systems.5. Apparatus5.1 Microscope, suitable for observation of particles in thesize range of 5 to 1000 m.5.2 Ultrasoni
11、c Probe,12 -in. (25.4-mm) tip, with the powerlevel to be determined by this guide.5.3 Ultrasonic BathPower level to be determined by thisguide.6. Reagents6.1 Purity of ReagentsReagent grade chemicals should beused in all tests. Unless otherwise indicated, it is intended thatall reagents should confo
12、rm to the specifications of theCommittee on Analytical Reagents of the American Chemical1This guide is under the jurisdiction of ASTM Committee B09 on MetalPowders and Metal Powder Products and is the direct responsibility of Subcom-mittee B09.02 on Base Metal Powders.Current edition approved Oct. 1
13、, 2016. Published October 2016. Originallyapproved in 1992. Last previous edition approved 2010 as B821 10. DOI:10.1520/B0821-10R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume inform
14、ation, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Society.3Other grades may be used, provided it is
15、firstascertained that the reagent is of sufficiently high purity topermit its use without lessening the accuracy of the determi-nation.6.2 SurfactantsSuggested surfactants are listed in Table 1and footnotes 4 through 6.4,5,67. General Dispersion Procedure7.1 The general procedure for determining and
16、 achievingproper dispersion is outlined in Fig. 17and described in detailbelow:7.1.1 Place a test portion of the powder to be analyzed in abeaker containing the carrier liquid, selected according to7.1.2.3Reagent Chemicals, American Chemical Society Specifications , AmericanChemical Society, Washing
17、ton, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.4Allen, T.,
18、Particle Size Measurement, 4th Edition, Chapman and Hall, London,UK, 1991.5Nelson, R. D., Dispersing Powders in Liquids, Elsevier, New York, NY, 1988.6SediGraph III 5120 Operators Manual, Micromeritics Corporation, Norcross,GA, 1998, pp. C-3, C-4, and H-3.7Microtrac Course Manual, Leeds and Northrup
19、 Company, St. Petersburg, FL,1989.TABLE 1 Recommended Dispersion ProceduresMaterialCarrierLiquidSurfactantSurfactantConcentrationUltrasonicTreatmentTypePowerLevel, WTime, minChromium carbide water none . noneorAbath.25.5Copper water Tween 21B35 dropsCbath 80 1Ferroalloys isopropyl alcohol Tween 21B1
20、0 % bath 80 1Iron/steel water Tween 21B35 dropsCbath 80 1Manganese sulfide water Tween 21B35 dropsCbath 80 1Molybdenum water sodium hexametaphosphate 0.01 % probeorbathorAbath16080253105Nickel water Tween 21B35 dropsCbath 80 1Tantalum water sodium hexametaphosphate 0.01 % probeorbath16080310Tantalum
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB82120102016STANDARDGUIDEFORLIQUIDDISPERSIONOFMETALPOWDERSANDRELATEDCOMPOUNDSFORPARTICLESIZEANALYSIS

链接地址:http://www.mydoc123.com/p-462389.html