ASTM A392-2011a(2017) Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric《镀锌钢连接链环栏栅织物的标准规格》.pdf

《ASTM A392-2011a(2017) Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric《镀锌钢连接链环栏栅织物的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A392-2011a(2017) Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric《镀锌钢连接链环栏栅织物的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A392 11a (Reapproved 2017)Standard Specification forZinc-Coated Steel Chain-Link Fence Fabric1This standard is issued under the fixed designation A392; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers zinc-coated steel chain-linkfence fabric, zinc coated either before or after weaving.1.2 The value

3、s stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with internationally recognized princ

4、iples on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight

5、Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA700 Guide for Packaging, Marking, and Loading Methodsfor Steel Products for ShipmentA817 Specification for Metallic-Coated Steel Wire forChain-Link Fenc

6、e Fabric and Marcelled Tension WireB6 Specification for Zinc2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipments (Civil Agencies)32.3 Military Standards:MIL-STD-129 Marking for Shipment and Storage3MIL-STD 163 Steel Mill Products, Preparation for Shipmentand Storage33. Terminology3.1 Definit

7、ions of Terms Specific to This Standard:3.1.1 chain-link fence fabrica fencing material made fromsteel wire helically wound and interwoven in such a manner asto provide a continuous mesh without knots or ties except inthe form of knuckling or of twisting the ends of the wires toform the selvage of t

8、he fabric. Variations to knuckled or twistedselvages are permissible.3.1.2 diamond countthe number of diamond openingsfrom one edge of the fabric to the other. The diamond count ofa given fabric shall begin at the first completed diamond at oneedge and continue to the unfinished (12) or full opening

9、 at theother edge.3.1.3 knucklingthe type of selvage obtained by interlock-ing adjacent pairs of wire ends and then bending the wire endsback into a loop. The loop shall be closed or nearly closed toa measurement less than the diameter of the wire.3.1.4 twistingthe type of selvage obtained by twisti

10、ngadjacent pairs of wire ends together in a close helix of 112machine turns, which is equivalent to 3 full twists, and cuttingthe wire ends at an angle. The wire ends beyond the twist shallbe at least14 in. (6.4 mm) long. This type of selvage is not usedon fabric with a mesh size of less than 2 in.

11、(50.8 mm).4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following information:4.1.1 Quantity (Section 14),4.1.2 Zinc coated after weaving or before weaving (Section5),4.1.3 Size of mesh (Section 7),4.1.4 Size of wire (Section 8),4.1.5

12、Height of fabric (Section 9),4.1.6 Diamond count, if specified (Section 6),4.1.7 Type of selvage (Section 10),4.1.8 Class of coating (Section 11),4.1.9 ASTM designation and year of issue, and4.1.10 Certification if required (Section 17).4.2 All rolls of fencing accepted by the purchaser shall bebill

13、ed on the basis of the original footage of the rolls beforesampling, unless changed by contractual arrangement.NOTE 1A typical ordering description is as follows: 25 rolls, 50 ft1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommit

14、tee F14.40 on Chain Link Fence andWire Accessories.Current edition approved June 1, 2017. Published June 2017. Originallyapproved in 1955. Last previous edition approved in 2011 as A392 - 11a. DOI:10.1520/A0392-171AR17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact A

15、STM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.Copyright A

16、STM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International St

17、andards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1each, chain-link fence fabric, zinc coated after weaving, 2-in. mesh,0.148-in. wire, 60 in. high, knuckled both selvages, Class 2 coating toASTM A392 - XX.5. Materials5.1 If zinc-c

18、oated before weaving, the wire from which thefabric is woven shall conform to all requirements of Specifi-cation A817 for Type II coating, in the class of coatingspecified (Class 4 or Class 5).5.2 If zinc-coated after weaving, the base metal shall besteel of such quality and purity that, when drawn

19、to the size ofwire specified and coated with zinc after fabrication, thefinished fencing shall be of uniform quality and have theproperties and characteristics as prescribed in this specifica-tion.5.3 Zinc for CoatingThe slab zinc, when used for thecoating, shall be any grade of zinc conforming to S

20、pecificationB6.6. Weave6.1 The wire shall be woven throughout in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 10.6.2 A

21、typical diamond count for each standard height isshown in Table 1. Other diamond counts are permissibleprovided that they are consistent within a lot. The purchaserhas the option to specify the diamond count (see 4.1.6).7. Size of Mesh7.1 The size of mesh shall be as indicated in Table 4.7.2 The per

22、missible variation from the specified size ofmesh shall be 618 in. (3.2 mm) for all mesh sizes larger than114 in. (31.75 mm), and 6116 in. (61.6 mm) for all mesh sizes114 in. (31.75 mm) and smaller.7.3 The size of mesh shall be determined by measuring theminimum clear distance between the wires form

23、ing the parallelsides of the mesh, and determined as the average of tworeadings taken at right angles to each other.8. Size of Wire8.1 Chain-link fabric shall be fabricated from wire diam-eters as listed in Specification A817, with a permissiblevariation from the specified diameter of the coated wir

24、e of60.005 in. (60.13 mm).9. Height of Fabric9.1 Chain-link fabric shall be furnished in the standardheights shown in Table 4. Custom order fabric is available inheights to and including 20 ft. (6.10 m). The height of fabricshall be the overall dimension from ends of twists or knuckles.Permissible v

25、ariation from the specified height shall be 61 in.(625 mm) for standard selvage on fabric with mesh sizes 1 in.(25.4 mm) and over 612 in. (613 mm) for all fabric with meshsizes less than 1 in. (25.4 mm).10. Selvage10.1 Unless otherwise specified by the purchaser, fabricswith2or218 in. (50 or 54 mm)

26、mesh, in heights 60 in. (1520mm) and under shall be knuckled at both selvages. Fabric 72in. (1830 mm) high and over shall be knuckled at one selvageand twisted at the other. (WarningTwisted selvages forfence fabric under 72 in. (1830 mm) in height are notrecommended because of consumer safety consid

27、erations.)10.2 The selvages of fabrics with meshes of less than 2 in.(50 mm) shall be knuckled.11. Weight of Zinc Coating11.1 The weight of zinc coating on the fabric may beordered in two coating weight classes as follows:TABLE 1 Typical Diamond CountANOTE 1Other diamond counts are permitted (see 6.

28、2).NOTE 2 For fabric heights over 144 in., see 6.2.NOTE 3Variations to knuckled or twisted selvage may affect diamond count (see 6.2).NominalDiameterCoatedWire, in.Size ofMesh,in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148

29、 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 134 1112 1312 1512 1912 2312 2712 3112 3512 3912 47120.148 114 17 21 23 29 35 41 46 52 58 700.148 1 20 23 27 33 39 45 53 61 67 790.120 2 1012 1212 1412 1712 2012 2412 . . . .0.120 134 1112 1312 1512 1912 2312 2712 3112 3512 3912 47120.120 114

30、 17 21 23 29 35 41 46 52 58 700.120 1 20 23 27 33 39 45 53 61 67 790.113 218 912 1112 1312 1612 1912 . . . . .ASee Appendix X1 for metric equivalents and Fig. 1 for mesh sizes less than 1 in. (25.4 mm).A392 11a (2017)211.1.1 Class 1The weight of zinc coating shall not be lessthan 1.2 oz/ft2(366 g/m2

31、) of uncoated wire surface as deter-mined from the average of two or more specimens, and not lessthan 1.08 oz/ft2(330 g/m2) of uncoated wire surface for anyindividual specimen.11.1.2 Class 2The weight of zinc coating shall not be lessthan 2 oz/ft2(610 g/m2) of uncoated wire surface as determinedfrom

32、 the average of two or more specimens, and not less than1.8 oz/ft2(500 g/m2) of uncoated wire surface for any indi-vidual specimen.NOTE 2Fabric galvanized after fabrication is normally not producedwith a Class 2 coating on 0.120-in. (3.05-mm) or 0.113-in. (2.87-mm)wire or with mesh sizes smaller tha

33、n 2 inches.11.2 On fabric galvanized after weaving, the weight ofcoating shall be determined on one or more pieces of wireremoved from the fabric. These specimens may be of anylength over 12 in. (300 mm) and shall include both bends andstraight sections, but shall not include either twists or knuckl

34、es.11.3 The weight of coating shall be determined in accor-dance with Test Method A90/A90M.12. Breaking Strength12.1 Wire constituting the fabric shall meet the minimumbreaking strength listed in the Breaking Strength table ofSpecification A817 when tested in accordance with TestMethods and Definiti

35、ons A370. Specimens to establish confor-mance to this requirement shall consist of individual picketsfrom a section of the fence fabric. The specimens shall be ofsufficient length so as to be firmly gripped in the testingmachine after straightening. The actual gage length (distancebetween jaws) of t

36、he specimen shall be limited to the unde-formed length of wire between the two adjacent straightenedbends.13. Workmanship13.1 Chain-link fence fabric shall be produced by methodsrecognized as good commercial practices. The zinc coating ongalvanized-after-weaving fabric shall be applied in a continu-

37、ous process and shall not be applied to the fabric in roll form.The galvanized before-weaving fabric shall be woven usingproven industry procedures to ensure a smooth consistentsurface without penetrating to the substrate, except at theselvage cut ends, see Note 3.13.2 Excessive roughness, blisters,

38、 sal ammoniac spots,bruises, flaking, and white rust shall be noted. The GalvanizedAfter Weaving (GAW) process shall include the use of appro-priate apparatus for producing galvanized fabric so as toprevent excess material in the elbow joints that form thediamond mesh. The finished product shall exh

39、ibit free inde-pendent motion of overlapping wires that form the diamondmesh when in a free or installed state of tension. Any of theabove described defects listed in 13.1 and 13.2 that willcompromise the function of the product shall provide a basisfor rejection.NOTE 3On fabric that is zinc-coated

40、before weaving, rust formationson the cut ends of the wire at the fabric selvages are inherent character-istics of this material and do not warrant rejection of the fabric.14. Standard Length of Rolls14.1 The standard length of roll shall be 50 ft (15.24 m) 61 % except as otherwise agreed upon at th

41、e time of purchase.14.2 The length of roll shall be determined by unrolling aroll of fabric on a flat surface and exerting tension byappropriate means to remove all slack. The tension appliedshall not reduce the actual height of the fabric by more thanTABLE 2 Available Mesh Sizes and Zinc Coating We

42、ightsASpecified Diameter of Coated Wire, in. (mm) Mesh Sizes with a Class 11.20 oz/ft2(610) coating, in.Mesh Sizes with a Class 22.00 oz/ft2(366) coating, in.0.192 (4.88) 134 and 2 20.148 (3.76)12,58,1,114,134, and 2 134 and 20.120 (3.05)38,12,58,1,114,134, and 2 . . .0.113 (2.87) 218 .AMesh sizes o

43、f 114 in. or smaller are typically produced with Galvanized before Weave product.TABLE 3 Breaking StrengthSpecified Diameter ofCoated Wire, in. (mm)Breaking Strength,min, lbf (N)0.192 (4.88) 2170 (9650)0.148 (3.76) 1290 (5740)0.135 (3.43) 1290 (5740)0.120 (3.05) 850 (3780)0.113 (2.87) 750 (3340)TABL

44、E 4 Sizes of Wire and MeshANOTE 1 For fabrics heights over 144 in., see 9.1.SpecifiedDiameterofCoatedWire, in.Size,CoatedWireGaugeSize ofMesh,in.BHeight of Fence Fabric, in.0.192 6 2 36 42 48 60 72 84 96 108 120 1440.148 9 2 36 42 48 60 72 84 96 108 120 1440.148 9 134 36 42 48 60 72 84 96 108 120 14

45、40.148 9 114C36 42 48 60 72 84 96 108 120 1440.148 9 1 36 42 48 60 72 84 96 108 120 1440.148 912 36 42 48 60 72 84 96 108 120 1440.120 11 2 36 42 48 60 72 84 . . . .0.120 11 134 36 42 48 60 72 84 96 108 120 1440.120 11 114C36 42 48 60 72 84 96 108 120 1440.120 11 1 36 42 48 60 72 84 96 108 120 1440.

46、120 1138D36 42 48 60 72 84 96 108 120 1440.120 1112D36 42 48 60 72 84 96 108 120 1440.120 1158 36 42 48 60 72 84 96 108 120 1440.113 1112 218 36 42 48 60 72 . . . . .ASee Appendix X1 for metric equivalents.BSee Fig. 1 for mesh dimensions for58 in.,12 in., and38 in. fence fabric. Thesesizes are typic

47、ally used for high security requirements.CThis mesh and smaller is recommended for swimming pools.DThese sizes are designed for security purposes.A392 11a (2017)3116 in. ft (5.3 mm/m) of height or by more than12 in. (12.7mm), whichever is less.15. Sampling and Number of Tests15.1 One roll from every

48、 50 rolls or fraction thereof in a lotshall be taken at random as a sample for test purposes. In nocase shall less than two samples be tested, except when the lotis less than 10 rolls, only one roll shall be selected for thesample.15.2 Sample rolls selected shall be inspected for weave(Section 6), s

49、ize of mesh (Section 7), diamond count (6.2), wiresize (Section 8), height of fabric (Section 9), selvage (Section10) and length (Section 14).15.3 On galvanized-after-weaving fabric, test specimenstaken from the outside end of the sample rolls shall be testedfor breaking strength (Section 12) and weight of zinc coating(Section 11).15.4 If any specimen tested fails to meet the requirements ofthis specification, the roll represented by the specimen shall berejected and two ad