AIR FORCE MIL-PRF-6086 F-2010 PERFORMANCE SPECIFICATION LUBRICATING OIL GEAR PETROLEUM BASE (NATO O-153 O-155)《石油基齿轮润滑油性能规范（NATO O-153 O-155）》.pdf

《AIR FORCE MIL-PRF-6086 F-2010 PERFORMANCE SPECIFICATION LUBRICATING OIL GEAR PETROLEUM BASE (NATO O-153 O-155)《石油基齿轮润滑油性能规范（NATO O-153 O-155）》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-PRF-6086 F-2010 PERFORMANCE SPECIFICATION LUBRICATING OIL GEAR PETROLEUM BASE (NATO O-153 O-155)《石油基齿轮润滑油性能规范（NATO O-153 O-155）》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-PRF-6086F 25 January 2010 SUPERSEDING MIL-PRF-6086E 13 February 1998 PERFORMANCE SPECIFICATION LUBRICATING OIL, GEAR, PETROLEUM BASE (NATO O-153, O-155) AMSC N/A FSC 9150 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. METRIC Comments, suggestions, or questions

2、on this document should be addressed to HQ AFPET/PTPT, 2430 C Street, Bldg 70, Area B, Wright-Patterson AFB OH 45433-7632 or e-mailed to AFPET.AFTTwpafb.af.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at h

3、ttps:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6086F 2 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers two grades o

4、f petroleum-based lubricating oils for gears (see 6.1). This oil is identified by NATO Code Numbers O-153 and O-155 (see 1.2). 1.2 Classification. Oil covered by this specification shall be classified as one of the following two grades (see 6.2): a. Grade L Light; identified by military symbol OGL a

5、nd NATO Code O-153 (see 6.4). b. Grade M Medium; identified by military symbol OGR and NATO Code O-155 (see 6.4). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in oth

6、er sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specific

7、ation, whether or not they are listed. 2.2 Non-government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). ASTM International ASTM D9

8、1 Standard Test Method for Precipitation Number of Lubricating Oils (DoD Adopted) ASTM D92 Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester ( DoD Adopted) ASTM D97 Standard Test Method for Pour Point of Petroleum Products (DoD Adopted) ASTM D130 Standard Test Method for Co

9、rrosiveness to Copper from Petroleum Products by Copper Strip Test (DoD Adopted) ASTM D445 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) (DoD Adopted) ASTM D892 Standard Test Method for Foaming Characteristics of Lubricating Oil

10、s (DoD Adopted) ASTM D974 Standard Test Method for Acid and Base Number by Color-Indicator Titration (DoD Adopted) ASTM D1500 Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) (DoD Adopted) ASTM D2270 Standard Practice for Calculating Viscosity Index from Kinematic Viscosi

11、ty at 40 and 100C (DoD Adopted) ASTM D2783 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Four-Ball Method) (Copies of these documents are available online at http:/www.astm.org or the ASTM International, 100 Barr Harbor Drive, West Conshohocken PA 19428-2

12、959) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6086F 3 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of

13、this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. Any oil furnished under this specification shall be products that are authorized by the qualifying activity

14、for listing on the applicable qualified products list before contract award (see 4.3 and 6.4). 3.1.1 Requalification. Requalification will be required if there is a change in the base stock source, refining treatment or additives. A minor change in the fluid formulation may be made without requalifi

15、cation, but only after notification to, and approval by, the qualifying activity. The qualifying activity may, at its discretion, waive complete requalification or may require only partial requalification testing to determine the significance and acceptability of the proposed formulation change. 3.2

16、 Materials. The oil shall consist of base stock oil mixed with a suitable load-carrying additive. The additive shall not be corrosive or cause excessive foaming, and shall be completely compatible with the base stock. The oil shall be clear and free of visible water, suspended matter, dirt, sediment

17、 or other impurities when observed at room temperature (25C 2C). Recycled constituent materials shall not be used. 3.3 Properties. The physicochemical properties of the finished gear oil shall be as specified in Table I and 3.4.1 TABLE I. Physicochemical properties. Property Requirements, grade L Re

18、quirements, grade M Units of measurement Test method Viscosity 23-34 60-82 mm2/s at 37.8C ASTM D445 Viscosity index 80 80 (minimum) ASTM D2270 Flash point 137.8 154.5 C (minimum) ASTM D92 Pour point - 40 - 28.9 C (maximum) ASTM D97 Load wear index 40 40 kg (minimum) ASTM D2783 Precipitation number 0

19、.1 0.1 mL (maximum) ASTM D91 Acid number 1.0 1.0 mg KOH/g (maximum) ASTM D974 ASTM color 8 8 (maximum) ASTM D1500 Foaming Characteristics (tendency, stability) Sequence I Sequence II Sequence III 5, 0 20, 0 5, 0 5, 0 20, 0 5, 0 mL (maximum) mL (maximum) mL (maximum) ASTM D892 Provided by IHSNot for

20、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6086F 4 3.4 Performance. 3.4.1 Copper corrosion. When tested for a duration of three hours at a temperature of 100C using ASTM test method D130, the corrosion produced shall not exceed No. 2 on the ASTM Corrosion Scal

21、e in accordance with the D130 test method. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. Qualification inspection (see 4.2). b. Quality conformance inspection (see 4.3). 4.2 Qualification inspection. 4.2.1 Qualification

22、sampling. The qualification sample shall consist of a 1-gallon aliquot of the finished gear oil. At the discretion of the qualifying activity, a separate 1-ounce aliquot of the load-carrying additive may also be required. Information as noted in 6.4.2 must accompany the submission of a qualification

23、 sample. 4.2.2 Qualification testing. The qualification sample(s) shall be tested as specified in 4.4, Methods of Inspection. 4.2.3 Retention of qualification. In order to retain a qualified status and listing on the Qualified Products List (QPL), the manufacturer shall verify by certification to th

24、e qualifying activity that the product complies with the requirements of this specification. Periodic verification by certification shall be performed in two-year intervals from the date of original qualification. The qualification activity reserves the right to re-examine the qualified product when

25、ever deemed necessary to determine whether the product continues to meet any of the specification requirements. 4.3 Quality conformance inspection. The conformance inspection shall include the test for viscosity, viscosity index, flash point, acid number, copper corrosion, pour point, precipitation

26、number, foaming characteristics, and load wear index as described in 3.3 and 3.4. Samples shall be labeled completely with information identifying the purpose of the sample, name of the product, specification number, lot and batch number (see 6.7), date of sampling, and contract number. 4.4 Method o

27、f inspection. 4.4.1 Inspection. Unless otherwise specified, inspection testing shall be performed in accordance with 4.4.2 and the contractual requirements. 4.4.2 Physicochemical values. Testing shall be performed in accordance with the applicable methods specified in Table I and 3.4.1. Values for t

28、he physicochemical properties specified in section 3 apply to the arithmetic average of the determinations made on the samples for those values that fall within any stated repeatability or reproducibility limits of the applicable test methods. 5. PACKAGING 5.1 Packaging. For acquisition purposes, th

29、e packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are

30、 maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products,

31、 or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6086F 5 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Inten

32、ded use. The two grades of gear oil covered by this specification are intended for use in light-to-moderate-loaded gear trains or gear boxes that operate in low-to-medium-speed ranges down to -40C. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, an

33、d date of this specification. b. Grade and quantity of oil required. c. Packaging requirements (see 5. 1) to include size and type of container, level of packaging and level of packing required. 6.2.1 Purchase unit. The oil will be purchased by volume with the unit of volume being a U.S. gallon of 2

34、31 cubic inches at 15.6C (60F). 6.3 Material Safety Data Sheets. Contracting officers will identify those activities that require copies of completed Material Safety Data Sheets (MSDS) prepared in accordance with FED-STD-313. The pertinent Government mailing addresses for submission of data are list

35、ed in FED-STD-313. 6.4 Qualification. With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Products List QPL No. 6086 whether or not such products have actually been so listed by that

36、 date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or orders for the products cov

37、ered by this specification. Information pertaining to qualification of products may be obtained from HQ AFPET/PTPT, 2430 C Street, Bldg 70, Area B, Wright-Patterson AFB, OH 45433-7632. An online listing of products qualified to this specification may be found in the Qualified Products Database (QPD)

38、 at https:/assist.daps.dla.mil. 6.4.1 Qualification information. It is understood that the material furnished under this specification subsequent to final approval will be of the same composition and will be equal to products upon which approval was originally granted. In the event that the oil unde

39、r contract is found to deviate from the composition of the approval product, or that the product fails to perform satisfactorily, approval of such products will be subjected to immediate withdrawal from the QPL at the discretion of the qualifying activity. 6.4.2 Information to accompany qualificatio

40、n samples. Qualification samples must be submitted with an MSDS and the following information: a. A certified test report containing complete information as to the source and type of base stock and additive materials used for the test. b. The detailed formulation and composition of the finished prod

41、uct. c. Laboratory data showing quantitative results of all tests required by this specification. The samples and reports will be forwarded to HQ AFPET/PTPT, 2430 C Street, Bldg 70, Area B, Wright-Patterson AFB, OH 45433-7632. d. The samples will be plainly identified by securely attached durable ta

42、gs or labels marked with the following information: 1. Sample for qualification inspection with grade identity: LUBRICATING OIL, GEAR 2. Specification MIL-PRF-6086 3. Name of ingredient (for ingredient materials) 4. Name of manufacturer 5. Product code number 6. Date of manufacture Provided by IHSNo

43、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6086F 6 6.4.2.1 Formulation sheet example. An example of a satisfactory form for the formulation sheet, indicating the weight percentage and nature of each ingredient, is as follows: a. Petroleum oil base stock

44、(composition) percentage b. Load carrying additive (manufacturers name and number) percentage 6.5 International agreements. Certain provisions of this specification are the subject of international standardization agreements, ASIC Air Standard 15/1 and NATO STANAG 1135. When any amendment, revision

45、or cancellation of this specification is proposed that will effect or violate an international agreement, the departmental custodians will inform their respective Departmental Standardization Office (DepSo) so appropriate action may be taken with respect to the applicable international agreement. 6.

46、6 Disposal actions. 6.6.1 Background. Waste oil will be disposed of through a waste oil recovery program unless prohibited by local law. The oil will be disposed of in accordance to local law and regulations promulgated by the U.S. Environmental Protection Agency under Public Law 94-580, Resource Co

47、nservation and Recovery Act of 1976. 6.6.2 Handling and safety precautions. Personnel handling the oil will wear appropriate impervious clothing to prevent repeated or prolonged skin contact. Local appraisal is required for exact health and safety complications and to prescribe precise application o

48、f protective clothing. If skin or clothing becomes moistened with the product, personnel will promptly wash with soap or mild detergent and water. Respirators are not required unless there is an inhalation exposure to mists. Personnel will wear protective clothing when using the product and when cle

49、aning up spills. 6.7 Definitions. 6.7.1 Bulk lot. A bulk lot (batch) is an indefinite quantity of a homogeneous mixture of material (see 3.2) offered for acceptance in a single, isolated container or manufactured in a single plant run (not exceeding 24 hours) through the same processing equipment, with no change in the ingredient materials. 6.7.2 Packaged lot. A packaged lot is an indefinite number of one-quar