AECMA PREN 2996-005-2005 Aerospace Series Circuit Breakers Three-Pole Temperature Compensated Rated Current 1 A to 25 A Part 005 With Polarized Signal Contact Product Standard Edit.pdf

《AECMA PREN 2996-005-2005 Aerospace Series Circuit Breakers Three-Pole Temperature Compensated Rated Current 1 A to 25 A Part 005 With Polarized Signal Contact Product Standard Edit.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2996-005-2005 Aerospace Series Circuit Breakers Three-Pole Temperature Compensated Rated Current 1 A to 25 A Part 005 With Polarized Signal Contact Product Standard Edit.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD NORME AECMA AECMA NORM prEN 2996-005 Edition P 3 May 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Supersedes edition P 2 January 1999 D

2、escriptors: ENGLISH VERSION Aerospace series Circuit breakers, three-pole, temperature compensated, rated current 1 A to 25 A Part 005: With polarized signal contact Product standard Srie arospatiale Disjoncteurs tripolaires compenss en temprature, intensits nominales 1 A 25 A Partie 005 : Avec cont

3、act de signalisation polaris Norme de produit Luft- und Raumfahrt Schutzschalter, dreipolig, Temperaturkompensiert, Nennstrme von 1 A bis 25 A Teil 005: Mit polarisiertem Signalkontakt Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The Europ

4、ean Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content sh

5、all not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee fo

6、r Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for pu

7、blication 31 May 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction o

8、r networking permitted without license from IHS-,-,-prEN 2996-005:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA-STANs General Process Ma

9、nual, this standard has received approval for Publication. Contents Page 1 Scope 3 2 Normative references. 3 3 Dimensions and mass. 3 4 Characteristics. 5 5 Designation 10 6 Rated current code 10 7 Delivery codes 10 8 Marking. 11 9 Technical specification 11 Copyright Association Europeene des Const

10、ructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20053 1 Scope This standard specifies the characteristics of three-pole circuit breakers, temperature compensated with a rated cur

11、rent from 1 A to 25 A, used in aircraft on-board circuits at a temperature between 55 C and 125 C for ratings 15 A and 55 C and 90 C for ratings 15 A and at an altitude of 22 000 m max. These circuit breakers are operated by a push-pull type single push button (actuator), with delayed action “trip-f

12、ree“ tripping with a polarized signal contact which is open when main contacts are closed, and inversely. They will continue to function up to the short-circuit current. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refere

13、nces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2996-001, Aerospace series Circuit breakers, three-pole, temperature compensated, rated current 1 A to 25 A Part 001: Technical specification. 1)EN 3155-

14、016, Aerospace series Electrical contacts used in elements of connection Part 016: Contacts, electrical, male, type A, crimp, class S Product standard.1)EN 3841-305, Aerospace series Circuit breakers Test methods Part 305: Short-circuit performance. EN 6113, Aerospace series Circuit breaker, connect

15、ing and attachment hardware. 1)TR 6083, Aerospace series Cut-outs for installation of electrical components. 2)MIL-I-81969/1A, Installing and removal tools, connector electrical contact, type III, class 2, composition C. 3)MIL-I-81969/14C, Installing and removal tools, connector electrical contact,

16、type III, class 2, composition B. 3)MIL-S-19500, Semiconductor device, diode, silicon, fast recovery.3)FED-STD-595B, Colours used in Government Procurement. 3 Dimensions and mass 3.1 Dimensional characteristics The circuit breakers do not have to correspond to the pictorial illustration, only the di

17、mensions given shall be adhered to. Dimensions are in millimetres. See Figure 1. 1) Published as AECMA Prestandard at the date of publication of this standard. 2) Published as AECMA Technical Report at the date of publication of this standard. 3) Published by: Department of Defense (DOD), the Pentag

18、on, Washington D.C. 20301 USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20054 Key 1 Push button released 10 1 to 3 max. 2 Green co

19、lour according to FED-STD-595B No. 34090 11 3 White Gauge 20 connection pins according to EN3155-016M2018 4 Marking area, see Clause 8. 12 Indicative value 25 (see note) 5 Circuits deviding partition 13 Rated current marking (white on green) 6 Connecting screw and washer 14 7 Push button pressed Pos

20、itioning lug in accordance with the panel cut-out, as per TR6083C202 8 Lockwasher 15 Terminals shape free 9 Attachment nut F1 and F2: see EN 2996-001, Table 3. NOTE Tools noted in subclause 4.2.4 shall be applied without interfering with the terminal 2 connection. Even if circuit breakers are groupe

21、d. Figure 1 Configuration Dimensions Tolerances 341,50-0,5234,6 min.50,5 A12439 8,4 0,3C2B2A2C1B1A115,8 max.0,5A16,5 max.12,8 0,517,5215 0,8 15 0,80,5 AF2F11530 max.26,5 max.20 max.138 min.10130,5M12 x 13 min.6,35 0,42,5 0,318,5 1310,819,5 max.3max.6453453A7 min.5 0,536 247max.F1 and F2 : see EN 299

22、6-001 table 3A2 B2 C2814 10,2 0,317119,8 max.Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20055 3.2 Electrical diagram See Figure 2. T

23、erminal No. : 1 and 2: Main contacts 3 and 5: Signal contacts Figure 2 Electrical diagram 3.3 Mass 64 g max. (delivery code A including hardware). 3.4 Panel mounting See EN 2996-001. 4 Characteristics 4.1 Material, surface treatment See EN 2996-001. 4.2 Mechanical characteristics 4.2.1 Fasteners See

24、 EN 6113. 4.2.2 Recommended tightening torque of attaching nut for installation (4,75 0,25) Nm 4.2.3 Recommended tightening torque of connection hardware for installation (1,6 0,1) Nm A2 A1B2 B1C2 C13 5Push-button releasedA2 A1B2 B1C2 C13 5Push-button pressed3 5or3 5orCopyright Association Europeene

25、 des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20056 4.2.4 Recommended tools for contacts of auxiliary contact insertion and extraction plastic MIL-I-81969/14-11; meta

26、llic MIL-I-81969/1-02. 4.2.5 Resistance to vibrations 4.2.5.1 Combined test: ambient temperature at 70 C and vibrations Sinusoidal: 10 gn, see EN 2996-001. Random: 5,8 gn, see EN 2996-001. Low frequencies: 10 gn, see EN 2996-001. 4.2.5.2 Combined test: ambient temperature at 85 C, altitude and vibra

27、tions Sinusoidal: 3 gn, see EN 2996-001. 4.2.6 Resistance to shocks 50 gn, see EN 2996-001. 4.2.7 Mechanical endurance See Table 6. 4.3 Environment characteristics 4.3.1 Humidity See EN 2996-001. 4.3.2 Corrosion See EN 2996-001. 4.3.3 Contaminating liquids See EN 2996-001. 4.3.4 Overvoltage caused b

28、y lightning See EN 2996-001. 4.4 Electrical characteristics 4.4.1 Nominal voltages of main contacts See Table 1. Table 1 Nominal voltage 115/200 V a.c., 360 Hz to 800 Hz Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo

29、 reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20057 4.4.2 Diode of signal contact characteristics Max. current at 125 C: 0,5 A. Peak repetitive reversal voltage: 800 V min. Quality standard: JANTX according to MIL-S-19500. 4.4.3 Voltage drop at nand at low current

30、See Table 2. Table 2 Ratings A 1 2 2,5 3 5 7,5 10 15 20 25 U max. at n V 1,1 0,75 0,70 0,55 0,35 0,30 0,30 0,25 0,25 0,20 U max. at = 100mA mV 110 40 30 18 8 4 3 2,5 2,5 2,5 Signal circuit : 28 V d.c.; I = 3 mA : U 1,0 V. NOTE When a signal contact has been operated with a power greater than 60 mW a

31、nd/or with a voltage higher than 28 V d.c., it loses its low current quality. 4.4.4 Minimum and maximum tripping thresholds See Table 3. Table 3 Overload (in % of n) Minimum thresholds value 1 h Maximum thresholds value 1 h Ambient temperatures C Ratings On ground At 22 000 m On ground 23 5 110 105

32、140 55 5 110 105 160 70 5 All 105 100 140 90 5 20 and 25 90 80 140 125 5 1 to 15 90 80 140 NOTE 1 For detection of minimum threshold, all the poles are connected in series. NOTE 2 For detection of maximum threshold, load value is: - increased by about 20 % when one pole is submitted to the load and

33、other poles are not loaded; - increased by about 10 % when two poles are submitted to the load and the other one is not loaded; - not increased when the two other poles are loaded at 0,9 n. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with A

34、ECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20058 4.4.5 Overload trip See Table 4. Table 4 Overload (in % of n) 200 500 1 000 3 poles 1 pole 3 poles 1 pole 3 poles 1 pole Ambient temperatures C Ratings A Trip time s 23 5 2 to 20 55 5 All 40 48

35、 90 5 20 and 25 1,5 1,5 125 5 1 to 15 1,5 1,5 0,15 to 2,30 0,15 to 2,80 0,035 to 0,500 0,035 to 0,600 NOTE 1 When 3 poles are loaded, they will be connected in series. NOTE 2 When 1 pole is loaded, the two other poles are not loaded. 4.4.6 Short-circuit values See Table 5. Table 5 Nominal voltage 11

36、5/ 200 V a.c., 360 Hz to 800 Hz 0,8 cos 1 Prospective currents 1 800 A r.m.s. 1 500 A r.m.s. 1 100 A r.m.s. Test altitudes On the ground and at maximum altitude (22 000 m, 4 000 Pa) On the ground and at cabin maximum altitude (4 600 m, 57 400 Pa) At maximum altitude (22 000 m, 4 000 Pa) Number of op

37、erations See note. 1 CO a+ 2 OCO b1 CO a+ 2 OCO bNOTE For the test at 1 800 A, an opening of the circuit by a destruction of the circuit breaker, (without bursting, flaming or thick smokes) is allowed even if this destruction happens during the first CO. If the product passes 1 CO + 2 OCO at 1 800 A

38、/115 V a.c., tests at 1 100 A and 1 500 A will not be necessary. aBreak operation (for definition see EN 3841-305). bMake operation (for definition see EN 3841-305). 4.4.7 No-load and load endurance See Table 6. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IH

39、S under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:20059 Table 6 Number of operations to be provided No-load Load 5 000 2 500 Main contacts Applicable Inductive 0,6 cos 0,7 n, 115/200 V a.c. - 360 Hz to 800 Hz All ratings Signal

40、 contacts Applicable Resistive 0,5 A, 28 V d.c. Resistive 3 mA, 28 V d.c Resistive 3 mA, 5 V d.c Lamp 0,2 A, 28 V d.c. NOTE 1 One operation corresponds to one closing + one opening. NOTE 2 Tolerances 5 % on current, voltage and frequency values. 4.4.8 Dielectric rigidity See Table 7. Table 7 Closed

41、position Z = 0 m Z = 22 000 m A1, B1, C1 with attachment A1, B1, C1 with 3 A1, B1, C1 with 5 A1, A2 with B1, B2 and C1, C2 B1, B2 with A1, A2 and C1, C2 1 500 V 400 V 3 with 5 3 and 5 with attachment 500 V 150 V Open position Z = 0 m Z = 22 000 m A1, B1, C1 with A2, B2, C2 A1, B1, C1, A2, B2, C2 wit

42、h attachment3 and 4 with A1, B1, C1 3 with 4 with A2, B2, C2 A1, A2 with B1, B2 and C1, C2 B1, B2 with A1, A2 and C1, C2 1 500 V 400 V 3 and 5 with attachment 500 V 150 V 4.4.9 Insulation resistance According to EN 2996-001, Table 5. Copyright Association Europeene des Constructeurs de Materiel Aero

43、spatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 2996-005:200510 5 Designation EXAMPLE Description block CIRCUIT BREAKER Identity block EN2996-005A20AA Number of EN standard Design code, A: green button Rated curr

44、ent code (see Table 8) Delivery code A (see Table 9) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Rated current code See Table 8. Table 8 Rating current n (A) 1 2 2,5 3 5 7,5 10 15 20 25 Marking on actuator 1 2 2 3 5 7 10 15 20 25 Rated cu

45、rrent code 01A 02A 2A5 03A 05A 7A5 10A 15A 20A 25A 7 Delivery codes See Table 9. Table 9 Connection and attachment hardware kits EN 6113 Delivery conditions Delivery code Kit part-No. aIncluded parts Pieces per part Fitted Supplied separately Connecting screw 6 Connecting lock washer 6 Attachment nu

46、t 1 A EN6113C1 Attachment lock washer 1 X Attachment nut 1 B EN6113B1 Attachment lock washer 1 X aSpare parts could be ordered separately, informations see EN 6113. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo repr

47、oduction or networking permitted without license from IHS-,-,-prEN 2996-005:200511 8 Marking As defined on the drawing and unless otherwise specified by contract, marking shall include: the designation defined in Clause 5 (without delivery hardware code), on the packaging; the manufacture date (year

48、, week); the manufacturers name or trademark; the electrical diagram and the terminal identification; the manufacturers part number (corresponding to the part number which includes connection and attachment hardware supplied separately in a bag). NOTE The marking could be on both opposite sides. For electrical diagram printed on the circuit breaker and/or terminal identification numbers see Figure 1. 9 Technical specification See EN 2996-001. Copyright Association Europeene des Constructeurs de Materie