ASTM D3690-2019 Standard Performance Specification for Vinyl-Coated and Urethane-Coated Upholstery Fabrics&x2014 Indoor.pdf
《ASTM D3690-2019 Standard Performance Specification for Vinyl-Coated and Urethane-Coated Upholstery Fabrics&x2014 Indoor.pdf》由会员分享,可在线阅读,更多相关《ASTM D3690-2019 Standard Performance Specification for Vinyl-Coated and Urethane-Coated Upholstery Fabrics&x2014 Indoor.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D3690 19Standard Performance Specification forVinyl-Coated and Urethane-Coated Upholstery FabricsIndoor1This standard is issued under the fixed designation D3690; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the yea
2、r of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This performance specification covers performance re-quirements for vinyl-coated and urethane-coated upholsteryfa
3、brics produced with woven, knit, or nonwoven substrateswhich are used in the manufacture of new indoor furniture.1.2 This performance specification is not applicable tofabrics used in porch, deck, or lawn furniture; nor for plain knitfabrics and plain, tufted, or flocked, woven upholstery fabrics.1.
4、3 These requirements apply to the length and widthdirections for those properties where fabric direction is perti-nent.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pri
5、ate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelop
6、ment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD751 Test Methods for Coated FabricsD1175 Method of Test for Abrasion Resista
7、nce of TextileFabrics (Oscillatory Cylinder and Uniform Abrasion);Replaced by D 4157, D 4158 (Withdrawn 1981)3D1203 Test Methods for Volatile Loss From Plastics UsingActivated Carbon MethodsD2097 Test Method for Flex Testing of Finish on UpholsteryLeatherD2136 Test Method for Coated FabricsLow-Tempe
8、ratureBend TestD4157 Test Method for Abrasion Resistance of TextileFabrics (Oscillatory Cylinder Method)D5034 Test Method for Breaking Strength and Elongation ofTextile Fabrics (Grab Test)2.2 AATCC Standards:4TM8 Colorfastness to Crocking: AATCC CrockmeterMethodTM16.3 Colorfastness to Light: Xenon-A
9、rcTM116 Colorfastness to Crocking: Rotary Vertical Crock-meter MethodEP1 Gray Scale for Color ChangeEP8 9-Step Chromatic Transference Scale2.3 Chemical Fabrics and Film Association Standards:5CFFA-5 Test for BlockingCFFA-20 Test for Tearing Strength, Procedure BTongueMethodNOTE 1Reference to test me
10、thods in this specification give only thepermanent part of the designation of ASTM, AATCC, or other testmethods. The current editions of each test method cited shall prevail.3. Terminology3.1 Definitions:3.1.1 blocking, nthe measurement of the development ofsurface tack and the thermal softening poi
11、nt of the material.3.1.2 hydrolytic stability, nthe ability to withstand theenvironmental effects of high humidity.3.1.3 tack tear, nthe measurement of the resistance of acoated fabric to tearing under conditions simulating an instal-lation that has been tacked in place.1This performance specificati
12、on is under the jurisdiction of ASTM CommitteeD13 on Textiles and is the direct responsibility of Subcommittee D13.63 on HomeFurnishings.Current edition Jan. 15, 2019. Published February 2019. Originally approved in1978. Last previous edition approved in 2008 as D3690 02(2008) which waswithdrawn Jan
13、uary 2018 and reinstated in January 2019. DOI: 10.1520/D3690-19.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM websi
14、te.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists(AATCC), P.O. Box 12215, Research Triangle Park, NC 27709, http:/www.aatcc.org.5Available from Chemical Fabrics and Film Association, 1230 Keit
15、h Bldg.,Cleveland, OH 44115.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles
16、 for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.1.3.1 DiscussionTack tear is intended primarily fortesting vinyl-coated fabrics for furniture or automotive appli-cations.3.2 For definitio
17、ns of other textile terms used in thisspecification, refer to Terminology D123 and to the TechnicalManual of the American Association of Textile Chemists andColorists.44. Significance and Use4.1 Fabrics intended for this end-use should meet all therequirements listed in Table 1.4.2 It should be reco
18、gnized that fabric can be producedutilizing an almost infinite number of combinations of con-struction variables (e.g., type of fibers, percentage of fibers,yarn twist, yarn number, warp and pick count, chemical andmechanical finished). Additionally, fashion and aesthetics dic-tate that the ultimate
19、 consumer may find acceptable articlesmade from fabrics that do not conform to all of the require-ments in Table 1.4.2.1 Hence, no single performance specification can possi-bly apply to all the various fabrics that could be utilized for thisend-use.4.3 The uses and significance of particular proper
20、ties andtest methods are discussed in the appropriate sections of thespecified methods.5. Performance Requirements5.1 The properties of vinyl-coated or urethane-coated up-holstery fabrics shall conform to the specification requirementsof one of the three categories in Table 1.6. Test Methods (see No
21、te 1)6.1 Breaking ForceDetermine the dry breaking force inthe standard atmosphere for testing textiles, as directed in TestMethod D5034, using a constant- rate- of- extension (CRE)tensile testing machine.6.2 Tongue Tear StrengthDetermine tongue tear strengthas directed in Procedure B of CFFA Method
22、20 using a CRTtensile testing machine.6.3 Tack-Tear ResistanceDetermine the tack-tear resis-tance as directed in Sections 43 to 47 of Test Methods D751.6.4 Adhesion of Coating to Substrate:6.4.1 Determine the adhesion of coating to substrate asdirected in Sections 39 to 42 of Test Methods D751, with
23、 thespeed of the pulling clamp at 12 612 in. (305 6 13 mm)/min.6.4.2 Report adhesion in pounds-force per inch (newtonsper metre) of width.6.5 Surface Abrasion:6.5.1 Determine the surface abrasion as directed in Sections33 to 42 of Test Methods D4157.6.5.2 After 200 cycles, the test specimens are rat
24、ed visuallyfor color change.TABLE 1 Performance RequirementsPropertyRequirementsSectionGrade A Grade B Grade CBreaking strength (load) (CRT Method):A6.1LengthWidth244 N (55 lbf), min244 N (55 lbf), min222 N (50 lbf), min222 N (50 lbf), min200 N (45 lbf), min178 N (40 lbf), minTongue tear strength (C
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD36902019STANDARDPERFORMANCESPECIFICATIONFORVINYLCOATEDANDURETHANECOATEDUPHOLSTERYFABRICSX2014INDOORPDF

链接地址:http://www.mydoc123.com/p-1243596.html