SMPTE RP 69-2002 Specifications for Scanning-Beam Uniformity Test Film for 35-mm Motion-Picture Audio Reproducers《35 mm电影还音器(摄影型)扫描光束均匀性试验片规范》.pdf

《SMPTE RP 69-2002 Specifications for Scanning-Beam Uniformity Test Film for 35-mm Motion-Picture Audio Reproducers《35 mm电影还音器(摄影型)扫描光束均匀性试验片规范》.pdf》由会员分享，可在线阅读，更多相关《SMPTE RP 69-2002 Specifications for Scanning-Beam Uniformity Test Film for 35-mm Motion-Picture Audio Reproducers《35 mm电影还音器(摄影型)扫描光束均匀性试验片规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、SMPTE RECOMMENDED PRACTICE RP 69-2002 Revision of RP 69-1997 Specifications for Scanning-Beam Uniformity Test Film for 35-mm . Motion-Picture Audio Reproducers - Page 1 of 3 pages 1 Scope 1.1 This practice describes a test film, the use of which is limited to the determination of the uniformity of s

2、canning-beam illumination in 35-mm motion-picture audio reproducers. 1.2 This test film is not intended to be used for the determination of the correct position of the scanning beam with respect to the reference edge of the film. 2 Normative references The following standards contain provisions whic

3、h, through reference in this text, constitute provisions of this practice. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this practice are encouraged to investigate the possibility of applying the most recent

4、edition of the standards indicated below. ANSVSMPTE 139-1996, Motion-Picture Film (35-mm) - Perforated KS SMPTE 40-2002, Motion-Picture Film (35-mm) - Release Prints - Photographic Audio Records SMPTE 223M-2001, Motion-Picture Film - Safety Film 3 Test film 3.1 The test film shall be a directly-reco

5、rded positive or a print from an original negative. 3.2 The test record on the film shall reproduce at a frequency of 1000 Hz k 20 Hz when the linear velocity of the film is 96 perforations per second or approximately 90 frnin (18 in or 45.7 cm/s). 3.3 At full modulation, the test record shall have

6、a width of 0.0050 in k 0.0005 in (0.127 mm k 0.01 3 mm), as measured between opposite amplitude peaks. It shall be approximately sinusoidal. 3.4 The test record shall move laterally at a uniform rate from one edge of the scanned area to the other, as specified in figure 1. 3.5 In any one test film,

7、the combined effect of variation in modulation width and density of the exposed and unexposed areas shall result in a signal amplitude variation not exceeding k 0.8 dB with respect to the average signal amplitude. Copyright O 2002 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hart

8、cdale Ave., White Plains, NY 10607 (914) 761-1100 Approved July 26,2002 RP 69.2002 4 Definitions 4.1 edges: For the purpose of this practice, the edge of the test track nearest the reference edge of the film shall be called the outboard edge, and the opposite edge shall be called the inboard edge. 4

9、.2 centerlinesweep: The centerline sweep of the test track is defined as the lateral displace- ment of the centerline of the test track from its initial position to its final position. Dimension D is the nominal centerline sweep. , 4.3 total test track sweep: The total test track sweep is defined as

10、 the sum of the centerline sweep and the overall width of the test track. Dimension C is the nominal total sweep. 5 Dimensions The dimensions and position of the audio track shall be as specified in figure 1 and table 1. Dimension Aextends to the inboard edge of the test track in its initial positio

11、n. Dimension B extends to the outboard edge of the test track in its final position. Dimensions A and i3 shall be measured at points opposite the first image area frameline next to the start and end splice of the test record negative. Dimension C, nominal total sweep, is 0.002 in (0.05 mm) less than

12、 the width of the scanning slit to avoid scanning of the edge of the slit. 6 Film stock The film stock, preferably polyester, shall be splice-free, of the low-shrinkage, safety type in accordance with SMPTE 223M, and cut and perforated in accordance with long-pitch dimensions specified in ANSVSMPTE

13、139. 7 Density The exposed track area shall have a minimum diffuse densrty of 2.0 above base density and the unexposed track area shall have a maximum densrty ot 0.10 above base density. The iongitudinai vanations of these specified densities shall not result in a reproduced output variation exceedi

14、ng f 0.5 dB. 8 Width of exposed area The overall width of the exposed track area shall exceed the maximum variation in the scanned area by no less than 0.010 in (0.25 mm) on each side of the slit. The maximum width of the scanning slit as specified by SMPTE 40 is 0.085 in (2.16 mm). This requires a

15、minimum printed width of 0.106 in (2.69 mm) to ensure a dense area adjacent to the scanned area. 9 Test film length Each test film shall carry three identical prints of the total length of the test record. In each, the test record shall start near the edge of the film and travel toward the image are

16、a. The length of the test record shall be approximately 30 ft (9.14 m). NOTE - A test film conforming to this practice is available from the Society of Motion Picture and Television Engineers. I Page 2 of 3 pages I RP 69.2002 REFERENCE - EDGE SEE SEC. 3.3 DIRECTION OF FILM TRAVEL Figure 1 - Scanning

17、-beam track position Table 1 - Dimensions Dimensions Inches Millimeters 0.000 + 0.00 0.285 +_ 0.001 7*24 - 0.03 A B C 0.082 nom 2.08 nom D 0.077 nom 1.96 nom Annex A (informative) Additional data Before the test film described in this practice is used, it is recommended that correct placement of the

18、 scanning beam be determined by means of a buzz-track test film as specified in SMPTE RP 68. The uniformity of scanning-beam illumination should be measured by an rms voltmeter calibrated in decibels with an accuracy of t 0.1 dB over the bandwidth 31.5 Hz to 16 kHz, connected to the output of the au

19、dio projector amplifier. The illumination of the scanning beam should be adjusted according to the instructions furnished by the equipment manufacturer. Variations of the output of the meter should be observed while running the full length of one test track print, spliced into a loop, through the equipment. Annex B (informative) Bibliography SMPTE RP 68-2002, Specifications for Buzz-Track Test Film for 35-mm Motion-Picture Photographic Audio Reproducers Page 3 of 3 pages