GSA AA-C-00297-1963 CHAIR STRAIGHT TUBULAR STEEL《钢制管材椅背挺直椅子》.pdf

《GSA AA-C-00297-1963 CHAIR STRAIGHT TUBULAR STEEL《钢制管材椅背挺直椅子》.pdf》由会员分享，可在线阅读，更多相关《GSA AA-C-00297-1963 CHAIR STRAIGHT TUBULAR STEEL《钢制管材椅背挺直椅子》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、INTERIM FEDERAL SPECIFICATION CHAIR, STRAIGHT, TUBULAR STEEL This interim Federal Specification was developed by the Standardization Division, Federal Supply Service, General Services Administration, Washington 26, D. C. , based upon currently available technical informa- tion. It is recommenddd tha

2、t Federal agenctes use it in procurement and fomvard recommendations for changes to the preparing activity at the address shown above, 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers requirements for materials and their assembly into sturdily construct-i tubular steel chaiB.of one t

3、ype (see Figure 1). 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids form a part of this specification to the extent specified herein. Federal Specifications: MMM-A - 1 O0 MMM-A - 125 MMM-A - 1 88 P PP-B- 57 6 PPP-B- 59 1 PPP-B-601 PPP-B- 621

4、PPP-B-636 PPP-U- 843 PPP-E-911 - Adhesive, Animal. Gelatin - Adhesive, Casein-Type, Water-and Mold-Resistant - Adhesive, Urea-Resin-Type (Liquid and Powder) - Box, Wood, Cleated, Veneer, Paper Overlain - Boxes, Fiberboard, Wood-Cleated - Boxes, Wood, Cleated-Plywood - Boxes, Wood, Nailed and Lock-Co

5、rner - Box, Fiberboard - Cushioning Material, Cellulosic - Excelsior, Wood, Fabricated Pads and Bulk Form March 22, 1963 FOR INSTRUCTIONS ON OBTAINING COPES OF FEDERAL SPECIFICATIONS AND STANDARDS, SEE LAST PAGE. - I FSC 7105 Page 1 of 13 Licensed by Information Handling ServicesAA-C=00297(GSA-FSS)

6、-2- Military Specifications: MIL-R-5001 MIL-L-10547 - Liners, Case, Waterproof - Rubber, Latex Foam Sponge Military Standards: MIL-STD- 105 MIL-STD-129 - Sampling Procedures and Tables for Inspection - Marking for Shipment and Storage by Attributes (Copies of Military specifications and standards re

7、quired by contractors in connection with specific prowrement functions should be obtained from the procuring activity or as directed by the contracting officer. ) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indica

8、ted, the issue in effect on date of invitation for bids shall apply. Department .of Commerce : CS 35-61 Hardwood Plywood ( Copies of Department. of Commerce publications are available from the Department of Commerce, Washimgton, D. C. 3. REQUIREMENTS . 3.1 Preproduction sample. Unless otherwise spec

9、ified (see 6.1) and as soon as . practicable after award of the contract or order and prior to submission of any complete units for final acceptance, the supplier shall furnish a preproduction sample for inspection to determine conformance to this specification. Approval of the pre- production sampl

10、e by the activity concerned shall not relieve the supplier of his obliga- tion to supply furniture conforming to this specification. No changes or deviations from the approved preproduction sample will be acc .ptable without prior written approval from the contracting officer. 3.2 Identical items, A

11、ll units of the same classification furnished under any specific contract shall be physically mechanically identical. This requirement includes parts, assemblies, components, and accessories. No deviations will be acceptable without prior written approval, shown, however, the items shown represent t

12、he typical design required. Alternate designs offered shall be similar. 3.3 Design. The design shown on Figure 1 is not restrictive to the details c Licensed by Information Handling ServicesAA-C-00277 73 979777q 0039675 3 1.1 Chair frames. All metal frame members shall be round section tubular steel

13、 conforming to 3.4.5. Legs shall be minimum 7/8 inch outside diameter, maximum 1-1/8 inches outside diameter. Legs may be swaged or tapered to smaller diameter as design requires. Each leg shall be fitted with ferrules and glides conforming to 3.4.3. Alternatively, rubber cushioned, self+locking umb

14、rella type glides having floor contact surface of stainlem steel may be used. Frame shall be of the wraparound type, with rear legs of one cmtinuous tube, extending along chair sides and across front under seat, - 3.5.1.2 Se.at Seat base shall be a minimum 1/2 inch thick water resistant plywood pane

15、l, conforming to 3.4.6.1, Licensed by Information Handling ServicesAsh Beech Birch Cherry Elm Hackberry Hickory Holly M ab0 gany Maple Magnolia Oak Pecan Sweet Gum Sycamore Walnut Y ellow Poplar Licensed by Information Handling Services- 1 AA-C-00277 71 = 7777774 0017b78 7 I AA-C- 00297 (MA- FSS) -

16、6- 3.5.1.5 Back. - Chair backs shall be a rigidly constructed wood frame with heavy chipboard over frame at front and back, or may be of 3-ply lumber core plywood of at least 1 Inch nominal tbieknes3. Backs shall be padded with a minimum of 1/2 inch of homogeneous, bonded, cellulose fiber padding, o

17、x* a minimum thichess f %/2 imh of latex foam confosm: top of seat. Under- side of seats shall be covered with a chipboard ar Manila cover of minimum O. 095 inch thickness, or equivalent cover material, stapled to underside of panel. Cover shall be of the same contour as the seat, and shall cover al

18、l tacks and edges of fabric, The back shall be self-welted along the edge of the top and ends. 3.6 Gluin 3 Level C. - The chairs shall be packed to insure carrier acceptance and safe delivery to destination in a container complying with the rules and regulations applicable to the mode of transportat

19、ion. . 5.3 MaZing 5.3.1 Civil ageicies. In addition to any special marking required by the contract or order, packages and shipping containers shall be marked in accordance with Fed. Std. No. 123. .% 5.3.2 Military requirements In addition to any special marking required by the contract or order, pa

20、ckages and shipping containers shall be marked in accordance - _ - with MIL-STD-129.- 6. NOTES 6.1 Ordering data. Procurement documents should specify the following: (a) Title, number, and date of this specification (b) Quantity required (c) if preproduction sample is not required (see 3.1) 8 (d) Upholstery material required (see 3.5. I. 6) (e) Level of packaging and level of packing require (see 5.1 and 5,Z) GSA WASH DC 63-13821 Licensed by Information Handling Services.” . FIG. 1 i . . : . . -. .- Licensed by Information Handling ServicesLicensed by Information Handling Services