ETSI EN 302 066-2017 Short Range Devices (SRD) Ground- and Wall- Probing Radar applications (GPR WPR) imaging systems Harmonised Standard covering the essential requirements of art.pdf

《ETSI EN 302 066-2017 Short Range Devices (SRD) Ground- and Wall- Probing Radar applications (GPR WPR) imaging systems Harmonised Standard covering the essential requirements of art.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 302 066-2017 Short Range Devices (SRD) Ground- and Wall- Probing Radar applications (GPR WPR) imaging systems Harmonised Standard covering the essential requirements of art.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 302 066 V2.1.1 (2017-01) Short Range Devices (SRD); Ground- and Wall- Probing Radar applications (GPR/WPR) imaging systems; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 066 V2.1.1 (2017-01) 2

2、 Reference REN/ERM-TGUWB-138 Keywords harmonised standard, radar, radio, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfectur

3、e de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be mod

4、ified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

5、Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please s

6、end your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permissi

7、on of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the E

8、TSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 066

9、 V2.1.1 (2017-01) 3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g33.3 Abbreviations . 9g34 Techni

10、cal requirements specifications . 9g34.1 Environmental conditions . 9g34.2 General . 9g34.3 Transmitter Conformance Requirements 10g34.3.1 Operating Bandwidth 10g34.3.1.1 Applicability 10g34.3.1.2 Description 10g34.3.1.3 Limits 10g34.3.1.4 Conformance . 10g34.3.2 Maximum value of mean power spectral

11、 density . 10g34.3.3 Maximum value of peak power 10g34.3.4 Exterior Limits 10g34.3.4.1 Applicability 10g34.3.4.2 Description 10g34.3.4.3 Limits 10g34.3.4.4 Conformance . 11g34.3.5 Total Power . 11g34.3.6 Other Emissions 11g34.3.7 Transmitter unwanted emissions . 11g34.4 Receiver Conformance Requirem

12、ents 11g34.4.1 General 11g34.4.2 Receiver spurious emissions . 11g34.4.3 Receiver interference handling . 11g34.4.3.1 Applicability 11g34.4.3.2 Description 11g34.4.3.3 Limits 12g34.4.3.4 Conformance . 12g34.5 Requirements for spectrum access . 12g34.5.1 Detect and Avoid (DAA) 12g34.5.2 Listen-before

13、-talk (LBT) 12g34.5.3 Low Duty Cycle (LDC) 12g34.6 Antenna Requirements . 12g34.7 Other Requirements and Mitigation techniques . 12g34.7.1 Adaptive/Transmit Power Control (TPC) . 12g34.7.2 Activity factor . 12g34.7.3 Frequency Domain Mitigation 12g34.7.4 Shielding effects . 12g34.7.5 Thermal Radiati

14、on 12g34.7.6 Site registration . 13g34.7.7 Deactivation mechanism . 13g35 Testing for compliance with technical requirements 13g35.1 Environmental conditions for testing . 13g35.2 General conditions for testing 13g3ETSI ETSI EN 302 066 V2.1.1 (2017-01) 4 5.2.1 Product information 13g35.2.2 Requireme

15、nts for the test modulation . 13g35.2.3 Test conditions, power supply and ambient temperatures 13g35.2.4 Choice of equipment for test suites . 13g35.2.5 Multiple Operating bandwidths and multiband equipment . 13g35.2.6 Testing of host connected equipment and plug-in radio devices 13g35.3 Interpretat

16、ion of the measurement results 14g35.3.0 General 14g35.3.1 Measurement uncertainty is equal or less than maximum acceptable uncertainty 14g35.3.2 Measurement uncertainty is greater than maximum acceptable uncertainty . 14g35.3.3 Emissions 14g36 Conformance test suites 14g36.1 Introduction 14g36.2 In

17、itial Measurement steps . 14g36.3 Radiated measurements 14g36.3.1 General 14g36.3.2 Test sites and general arrangements for measurements involving the use of radiated fields 15g36.3.3 Guidance on the use of a radiation test site . 15g36.3.3.1 General 15g36.3.3.2 Range length . 15g36.3.4 Coupling of

18、signals . 15g36.3.5 Standard test methods . 15g36.3.5.1 Generic measurement method . 15g36.3.5.1.1 Calibrated setup . 15g36.3.5.1.2 Substitution method. 15g36.3.6 Standard calibration method . 15g36.4 Conducted measurements . 16g36.4.1 General Setup 16g36.4.2 Specific Setup . 16g36.5 Conformance met

19、hods of measurement for transmitter . 16g36.5.1 General 16g36.5.2 Method of measurements of the Ultra Wideband Emissions from GPR/WPR . 16g36.5.3 Operating Bandwidth(s) 16g36.5.4 Mean power spectral density measurements . 17g36.5.5 Peak power measurements 17g36.5.6 Exterior limit measurement. 17g36.

20、5.7 Total Power . 18g36.5.8 Transmitter unwanted emissions . 18g36.6 Conformance methods of measurement for receiver 18g36.6.1 Receiver spurious emissions . 18g36.6.2 Receiver interference handling . 18g36.7 Conformance test suits for spectrum access . 19g36.7.1 Detect and Avoid (DAA) 19g36.7.2 List

21、en Before Talk 19g36.7.3 Low Duty Cycle 19g36.8 Conformance test suites for antenna requirements . 19g36.9 Other test suites 19g36.9.1 Transmit Power control 19g36.9.2 Activity factor . 19g36.9.3 Frequency domain mitigation . 19g36.9.4 Shielding Effects . 19g36.9.5 Thermal Radiations. 19g36.9.6 Inst

22、allation requirements/site registration . 19g36.9.7 Deactivation mechanism . 19g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 20g3Annex B (informative): Application form for testing 21g3B.1 Introduction 21g3ETSI ETSI EN 302 0

23、66 V2.1.1 (2017-01) 5 B.2 General Information by ETSI EN 302 066, clause 5.2.1 21g3B.2.1 Type of Equipment (stand-alone, combined, plug-in radio device, etc.) 21g3B.2.2 The nominal voltages of the stand-alone radio equipment or the nominal voltages of the combined (host) equipment or test jig in cas

24、e of plug-in devices . 21g3B.3 Signal related Information by ETSI EN 302 066, clause 4.3 . 22g3B.3.1 Introduction 22g3B.3.2 Operational bandwidth(s) of the equipment . 22g3B.3.3 The worst case mode for each of the following tests 22g3B.4 RX test Information by ETSI EN 302 066, clause 4.4 . 22g3B.4.1

25、 Introduction 22g3B.4.2 Performance criterion and level of performance 22g3B.4.3 Interfering signals . 22g3B.5 Additional information provided by the applicant . 23g3B.5.1 About the DUT . 23g3B.5.2 Additional items and/or supporting equipment provided . 23g3Annex C (normative): Radiated measurements

26、 24g3C.1 Test sites and general arrangements for measurements involving the use of radiated fields . 24g3C.1.0 General . 24g3C.1.1 Test antenna 24g3C.1.2 Measuring antenna . 25g3C.2 Guidance on the use of radiation test sites . 25g3C.2.0 General . 25g3C.2.1 Verification of the test site . 25g3C.2.2

27、Preparation of the DUT 25g3C.2.3 Power supplies to the DUT. 25g3C.2.4 Range length . 25g3C.2.5 Site preparation 26g3C.2.6 Conversion of field strength to power limits 26g3Annex D (normative): Deactivation mechanism 27g3Annex E (informative): Measurement antenna and preamplifier specifications . 28g3

28、Annex F (normative): Calculation of the Mean Power Density. 29g3F.0 General . 29g3F.1 Measurement of , transmit pulse width. 30g3Annex G (informative): Bibliography . 32g3Annex H (informative): Change History 33g3History 34g3ETSI ETSI EN 302 066 V2.1.1 (2017-01) 6 Intellectual Property Rights IPRs e

29、ssential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or poten

30、tially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No

31、 guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee El

32、ectromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.5 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the law

33、s of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given i

34、n table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. National transposition dates Date of adoption of this EN: 23 December 2016 Date of latest announce

35、ment of this EN (doa): 31 March 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2017 Date of withdrawal of any conflicting National Standard (dow): 30 September 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should

36、“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI

37、 ETSI EN 302 066 V2.1.1 (2017-01) 7 1 Scope The present document specifies the requirements for Ground- and Wall- Probing Radar imaging systems applications. Ground Probing Radars (GPR) and Wall Probing Radars (WPR) are used in survey and detection applications. The scope is limited to GPR and WPR r

38、adars, in which the system is in close proximity to the materials being investigated. It does not include radars operated from aircraft or spacecraft. The GPR/WPR applications in the present document are not intended for communications purposes, and the intended signal is not radiated into free spac

39、e. NOTE: Equipment covered by the present document is intended to be used by competent professional personnel. The present document applies to: 1) Ground Probing Radars (GPR) operating in the frequency range 30 MHz to 12,4 GHz radiating directly downwards into the ground. 2) Wall Probing Radars (WPR

40、) operating in the frequency range 30 MHz to 12,4 GHz radiating directly into a “wall“. The “wall“ is a building material structure, the side of a bridge, the wall of a mine or another physical structure that absorbs a significant part of the signal transmitted by the radar. These equipment can eith

41、er: 1) be fitted with integral antennas and without antenna connector; or 2) use different imaging heads (antennas) with an antenna connector, to allow operation at different operating bandwidths frequencies. Equipment covered by the present document operates in accordance with ECC/DEC(06)08 “ECC De

42、cision of 1 December 2006 on the conditions for use of the radio spectrum by Ground- and Wall- Probing Radar (GPR/WPR) imaging systems“ i.2. These radio equipment types are capable of operating in all or part of the frequency bands given in table 1. Table 1: Permitted ranges of operation Permitted r

43、ange of operation Transmit 30 MHz to 12,4 GHz Receive 30 MHz to 12,4 GHz NOTE 1: Limits in table 2, clause 4.3.4 are to be met. NOTE 2: The frequency usage conditions for GPR/WPR are not fully harmonised in the EU and CEPT. Some National Regulatory Authorities (NRAs) may not have a general frequency

44、 allocation for GPR/WPT and may have established individual licensing requirements (e.g. registration of the user). Annex 2 of i.2 gives some guidance to administrations. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or

45、version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be

46、 found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. ETSI ETSI EN 302 066 V2.1.1 (2017-01) 8 The following referenced documents are necessary for the application of the pre

47、sent document. 1 ETSI EN 303 883 (V1.1.1) (09-2016): “Short Range Devices (SRD) using Ultra Wide Band (UWB); Measurement Techniques“. 2 ETSI TS 103 361 (V1.1.1) (03-2016): “Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Receiver technical requirements, parameters and measurement p

48、rocedures to fulfil the requirements of the Directive 2014/53/EU“. 3 CISPR 16 (2014) (parts 1-1, 1-4 and 1-5): “Specification for radio disturbance and immunity measuring apparatus and methods; Part 1: Radio disturbance and immunity measuring apparatus“. 2.2 Informative references References are eit

49、her specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subj