NAVISTAR MPAPS S-JM-1 101-GS PL-2015 Split (Cotter) Pins - Extended Prong - Metric Series (Noun Code - 6200).pdf

《NAVISTAR MPAPS S-JM-1 101-GS PL-2015 Split (Cotter) Pins - Extended Prong - Metric Series (Noun Code - 6200).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS S-JM-1 101-GS PL-2015 Split (Cotter) Pins - Extended Prong - Metric Series (Noun Code - 6200).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-JM-1.101-GS/PL Former Designation: ESP-JM-1.101-GS TITLE: Split (Cotter) Pins - Extended Prong - Metric Series (Noun Code - 6200) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-JM-1.101-GS - Aug

3、ust 2012 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriat

4、e safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, GI, PP, NPP. 1.0 GENERAL: Implementation of this standard must be in accordance with the policies and procedures outlined in MPAPS S-A-0.101. T

5、here may also be supplemental group instructions in regard to use of metric standards that should be taken into account. In formulating this standard for metric split pins, considerable investigation was devoted to an effort to establish interchangeability with the inch series pins in order to avoid

6、 the creation of separate part numbers, records, inventories, etc. However, significant dimensional differences in most sizes, primarily in head dimensions and recommended hole sizes, preclude this possibility. This specification contains the essentials of the following standards: International Orga

7、nization for Standardization: ISO R 1234 Association Francaise de Normalisation: NF E27-487 British Standards Institute: BS 1574 Deutsche Normen: DIN 94 Standards Association of Australia: AS 1236 The inclusion of dimensional data is not intended to imply that all the pins described are stock produc

8、tion sizes. Inch series split (cotter) pins may be found in MPAPS S-J-1.101-GS/PL. 2.0 DESIGN CONSIDERATION: Split pins are normally used to position and lock parts in alignment. They are also used as locking devices for other features such as clevis pins, shafts, threaded rods, etc. The optimum usa

9、ge of split pins is to lock slotted nuts. In these applications, the pin should be of sufficient length to provide a minimum of 6 mm protrusion of the longer leg beyond the nut flat. This allows adequate grip for bending the pin legs at installation. 3.0 METRIC-INCH RELATED SIZES: During the inch to

10、 metric design conversion period, the following chart of related sizes may be of value for handy reference. This information is not to be considered as recommended size substitutions but only as a means of quickly determining approximate dimensional equivalents. NUMBER: MPAPS S-JM-1.101-GS/PL TITLE:

11、 Split (Cotter) Pins - Extended Prong REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 4 Nominal

12、 Size Designation Metric Series (mm) Inch Series 1 1/32 1.6 1/16 2 5/64 2.5 3/32 3.2 1/8 4 5/32 5 3/16 6.3 1/4 8 * 5/16 10 * 3/8 13 * 1/2 16 * 5/8 20 * 3/4 * Non-preferred for new design. Use other locking design concepts. 4.0 NON-PREFERRED LENGTHS: In the event it is absolutely necessary to use len

13、gths other than those listed as preferred on page JM-1.101, the following should be adhered to: 4, 5, 14, 18, 22, 28, 36, 45, 56, 71, 90, 112, 140, 160, 180, 200, 224, 250, 280 5.0 METHOD OF DESIGNATION: Split pins will be designated on purchase orders by size, length, word designation, material, fi

14、nish, and part number as follows: 4 x 40 mm, Split Pin, STL, PLN, Part Number 6.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings. For new design, parts shall be selected from

15、 “Approved“ part list only. Nominal Sizes: 1, 1.6, 2, 2.5, 3.2, 4, 5, and 6.3 Material: Steel (STL) Finish: Plain (PLN) Lengths: See chart below Dimensions in millimeters: Nominal Size Nominal Length 1 1.6 2 2.5 3.2 4 5 6.3 6 X 8 X X 10 X X X 12 X X X X 16 X X X X X 20 X X X X X X 25 X X X X X X 32

16、X X X X X X X 40 X X X X X X 50 X X X X X 63 X X X X 80 X X X 100 X X 125 X For non-preferred lengths, see section 4.0 NUMBER: MPAPS S-JM-1.101-GS/PL TITLE: Split (Cotter) Pins - Extended Prong REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced withou

17、t permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 7.0 HEAD: The contour of the head will be optional with the manufacturer provided the specified dimensions are maintained and there is no sharp indenta

18、tion at the juncture of head and shank. 8.0 POINTS: All points will be the extended prong. The ends of points will not be open and any gaps occurring between the prongs along the shank portion of pins beyond the point will not exceed 0.4 mm. The lateral misalignment of prongs over the entire length

19、will not exceed 0.4 mm. 9.0 LENGTH: The length (L) will be measured parallel to the axis of pin, from the plane of contact of a ring gage with the head of pin (see Figure 1) to the end of shortest prong. The ring gage will have a hole or diameter equal to the nominal pin size within a tolerance of 0

20、.03 mm. The permissible break or rounding at the gaging edges of hole will not exceed 0.13 mm. Length measurement will be taken with pin inserted into gage under finger force not to exceed 2N. 10.0 TOLERANCE ON LENGTH: The tolerance on length will be as tabulated below: Dimensions in millimeters: No

21、minal Diameter Length Tol Up to and including 3.2 1.6 Over 3.2, Up to and including 6.3 2.0 Over 6.3, Up to and including 10 2.8 Over 10 3.0 11.0 WIRE SECTION: The material will be rolled or drawn from wire having a half-round section, the flat side of which preferably will have a small degree of ro

22、unding (a radius equal to 7.5 to 10 percent of the minimum pin diameter) at the edges rather than sharp corners. 12.0 MATERIAL: Steel (STL): MPAPS A-0, Part II, Code 0-100. Stainless Steel (SST): Type 18-8, MPAPS A-37; *passivated per MPAPS A-37 Type5. 13.0 DUCTILITY: Each prong of the cotter pin wi

23、ll be capable of withstanding being bent back upon itself (180 degrees) once with no visible indication of fracture occurring at the point of bend. 14.0 FINISHES: As designated by part number in accordance with the MPAPS and Class listed below: Plain (PLN) - Free from dirt and rust and coated with a

24、 light oil film. Zinc Trivalent (ZN6A) MPAPS G-20, Class 6A 15.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 16.0 WORKMANSHIP: Pins must be free from burrs

25、 and any other defects that might affect their serviceability. NUMBER: MPAPS S-JM-1.101-GS/PL TITLE: Split (Cotter) Pins - Extended Prong REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Supplie

26、rs are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 17.0 DIMENSIONS: Dimensions in millimeters: Nominal Size A B C D Recommended Recommended Usage Shank Head Outside Prong Head Hole Threaded Unthreaded Diameter Diameter Extension Height Size Components Compon

27、ents Max Min Max Min Max Min Approx Max Min Over To Over To 1 0.9 0.8 1.8 1.6 1.6 0.8 3 1.14 1 3.5 4.5 3 4 1.2 1 0.9 2 1.7 2.5 1.2 3 1.34 1.2 4.5 5.5 4 5 1.6 1.4 1.3 2.8 2.4 2.5 1.2 3.2 1.85 1.6 5.5 7 5 6 2 1.8 1.7 3.6 3.2 2.5 1.2 4 2.25 2 7 9 6 8 2.5 2.3 2.1 4.6 4 2.5 1.2 5 2.75 2.5 9 11 8 9 3.2 2.

28、9 2.7 5.8 5.1 3.2 1.6 6.4 3.5 3.2 11 14 9 12 4 3.7 3.5 7.4 6.5 4 2 8 4.3 4 14 20 12 17 5 4.6 4.4 9.2 8 4 2 10 5.3 5 20 27 17 23 6.3 5.9 5.7 11.8 10.3 4 2 12.6 6.66 6.3 27 39 23 29 8 * 7.5 7.3 15 13.1 4 2 16 8.36 8 39 56 29 44 10 * 9.5 9.3 19 16.6 6.3 3.2 20 10.36 10 56 80 44 69 13 * 12.4 12.1 24.8 2

29、1.7 6.3 3.2 26 13.43 13 80 120 69 110 16 * 15.4 15.1 30.8 27 6.3 3.2 32 16.43 16 120 170 110 160 20 * 19.3 19 38.6 33.8 6.3 3.2 40 20.52 20 170 - 160 - * Non-Preferred Sizes 18.0 PART LIST: 18.1 Approved: Nominal Size Length Finish Material Part Number 1.2 38 SST 40458R1 1.6 12 PLN CST 932951R1 2.5

30、50 PLN CST 30767R1 3.2 20 PLN CST 934792R1 4 25 PLN CST 30243R1 4 40 PLN CST 932956R1 4 20 ZN6A CST 934897R1 19.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/