SAE AMS 5696E-2015 Steel Corrosion and Heat-Resistant Welding Wire 19Cr - 12 5Ni - 2 5Mo High Ferrite Grade (UNS S31683).pdf

《SAE AMS 5696E-2015 Steel Corrosion and Heat-Resistant Welding Wire 19Cr - 12 5Ni - 2 5Mo High Ferrite Grade (UNS S31683).pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5696E-2015 Steel Corrosion and Heat-Resistant Welding Wire 19Cr - 12 5Ni - 2 5Mo High Ferrite Grade (UNS S31683).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2015 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5696EAEROSPACEMATERIAL SPECIFICATIONAMS5696 REV. EIssued 1984-07Noncurrent 2008-03Revised

5、2015-12Superseding AMS5696DSteel, Corrosion and Heat-Resistant, Welding Wire19Cr - 12.5Ni - 2.5Mo(Composition similar to UNS S31683)RATIONALEAMS5696E restores this document to active status. AMS5696E has been updated to incorporate the standard quality requirements of AMS materials as the ordering r

6、equirements for AWS specified wire, and is the result of a Five Year review and update of this specification.1. SCOPE1.1 FormThis specification covers a corrosion and heat-resistant steel in the form of welding wire.1.2 ApplicationThis wire has been used typically as bare wire filler metal for gas-t

7、ungsten-arc or gas-metal-arc welding of corrosion and heat-resistant steels and alloys, but usage is not limited to such applications.1.2.1 The relatively high ferrite content promotes weldability by combating microfissuring and minimizing cracking in heavy sections but limits use of the wire to app

8、lications not operating in the sigma-forming temperature range.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unles

9、s a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel

10、: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS2813 Packaging and Marking of Packages of Welding Wire, Standard MethodAMS2814 Packaging and Marking of Packages of Welding Wire, Premium QualitySAE INTERNATIONAL AMS5696E Page 2 of 4AMS2816 Identification Weldin

11、g Wire, Tab Marking MethodAMS2819 Identification, Welding Wire Direct Color Code SystemARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire2.2 AWS PublicationsAvailable from American Welding Society, 8669 NW 36 Street, #130, Miami, FL 33166-6672, Tel: 1-800-443-9353 or 305-

12、443-9353, www.aws.org.AWS A5.01 Welding Consumables Procurement of Filler Metals and Fluxes AWS A5.9/A5.9M Specification for Bare Stainless Steel Welding Electrodes and Rods3. TECHNICAL REQUIREMENTS3.1 Wire shall meet the technical requirements of AWS A5.9/5.9M ER316L and the following:3.2 QualityWi

13、re, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.3 Sizes and TolerancesWire shall be supplied in the si

14、zes and to the tolerances specified in AWS A5.9/5.9M. Smaller diameter wires, when ordered, shall be supplied in sizes and tolerances shown in 3.3.1.3.3.1 DiameterShall be as shown in Table 1.Table 1A - Sizes and diameter tolerances, inch/pound unitsFormNominal DiameterInchToleranceInchPlus and Minu

15、sCut Lengths 0.030, 0.035, 0.001Spools 0.007, 0.010, 0.015 0.0005Table 1B - Sizes and diameter tolerances, SI unitsFormNominal DiameterMillimeterToleranceMillimeterPlus and MinusCut Lengths 0.76, 0.89, 0.025Spools 0.18, 0.25, 0.38 0.013SAE INTERNATIONAL AMS5696E Page 3 of 44. QUALITY ASSURANCE PROVI

16、SIONS4.1 Responsibility for InspectionThe vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to

17、specified requirements.4.2 Classification of Tests4.2.1 Acceptance TestsComposition (3.1), sizes and tolerances (3.3), and alloy verification (5.2) are acceptance tests and shall be performed on each heat or lot as applicable.4.3 Sampling and TestingShall be in accordance with AWS A5.01 S3, testing

18、schedule 5 or J.4.4 ReportsThe vendor of wire shall furnish with each shipment a report showing the results of tests for composition and ferrite number of each heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and l

19、ot numbers, AMS5696E, nominal size, and quantity.4.5 Resampling and RetestingShall be in accordance with AWS A5.01.5. PREPARATION FOR DELIVERY5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool

20、or in each package of cut lengths shall be from the same heat of steel.5.2 Alloy VerificationWire on each spool or in each package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are recommended.5.2.1 An 8 inch (203 mm) length

21、of wire shall be accessible at both ends of each spool for alloy verification.5.3 IdentificationShall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser.5.4 Packaging and MarkingShall be in accordance with AMS2813 unless AMS2814 or another method is specified by

22、 purchaser.6. ACKNOWLEDGMENTA vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONSWire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.SAE INTERNAT

23、IONAL AMS5696E Page 4 of 48. NOTES8.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document

24、title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions and properties in inch/pound units and the

25、 Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS5696ESize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED BY AMS COMMITTEE “F“