ASTM F2576-2008 Standard Terminology Relating to Declarable Substances in Materials.pdf

《ASTM F2576-2008 Standard Terminology Relating to Declarable Substances in Materials.pdf》由会员分享，可在线阅读，更多相关《ASTM F2576-2008 Standard Terminology Relating to Declarable Substances in Materials.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2576 08Standard Terminology Relating toDeclarable Substances in Materials1This standard is issued under the fixed designation F 2576; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This terminology standard contains terms, definitions,descriptions of terms, nomenclature, and explanations of acro-nyms and symbols specifi

3、cally associated with standards underthe jurisdiction of ASTM International Committee F40 onDeclarable Substances in Materials.1.2 This terminology may also be applicable to documentsnot under the jurisdiction of ASTM F40, in which case thisterminology may be referenced in those documents.2. Referen

4、ced Documents2.1 ASTM Standards:2E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE 1964 Practice for Compiling and Writing available from ASTMInternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959; ASTM Stock Number: DEF00

5、.5Standard ISO 472 is under the jurisdiction of ISO TC 61 on Plastics and is thedirect responsibility of ISO TC 61 SC 1 on Terminology.6ISO/IEC Guide 2 is under the jurisdiction of the ISO Technical ManagementBoard.7VIM is under the jurisdiction of the Joint Committee for Guides in Metrology(JCGM) a

6、nd is the direct responsibility of JCGM-WG2.8Currie, Lloyd A., Pure refers to European CommissionDirective 2000/53/EC on End-of-Life VehiclesEUEuropean UnionGRASGenerally Recognized as SafeIUCLIDInternational Uniform Chemical Information Data-baseMCVMaximum Concentration Value; plural is MCVsMSDSMat

7、erial Safety Data SheetNESNew and Existing SubstancesPBBPolybrominated BiphenylPBDEPolybrominated Diphenyl EtherPCBPolychlorinated BiphenylPWBPrinted Wiring BoardRIPREACH Implementation ProjectSB20California Senate Bill 20; refers to State of California,USA Bill approved 9/29/2003 entitled Solid was

8、te; hazard-ous electronic wasteSB50California Senate Bill 50; refers to State of California,USA bill approved 9/24/2004 entitled Solid waste; hazard-ous electronic waste: solid waste disposal feesSDoCSupplier Declaration of ConformanceRoHSRestriction of Hazardous Substances; refers to Euo-pean Commi

9、ssion Directive 2002/95/EC on Restriction ofthe Use of Certain Hazardous Substances in Electrical andElectronic EquipmentWEEEWaste Electrical and Electronic Equipment; refers toEuropean Commission Directive 2002/96/EC on WasteElectrical and Electronic Equipment5. Keywords5.1 declarable; definitions;

10、 glossary; restricted; terminologyASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risko

11、f infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this

12、standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake yo

13、ur views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2576082