NAVISTAR MPAPS S-JM-7 101-GS-2015 Clevis Pins - Metric Series (Noun Code - 6200).pdf

《NAVISTAR MPAPS S-JM-7 101-GS-2015 Clevis Pins - Metric Series (Noun Code - 6200).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS S-JM-7 101-GS-2015 Clevis Pins - Metric Series (Noun Code - 6200).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-JM-7.101-GS Former Designation: ESP-JM-7.101-GS TITLE: Clevis Pins - Metric Series (Noun Code - 6200) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-JM-7.101-GS - August 2006 PRINTED COPIES OF T

3、HIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practice

4、s and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, GI, PP. 1.0 GENERAL: Implementation of this standard must be in accordance with the policies and procedures outlined in MPAPS S-A-0.101. There may also be divisional suppl

5、emental instructions in regard to use of metric standards that should be taken into account. This specification contains the essentials of the following standards: International Organization for Standardization: ISO 2341 Inch series clevis pins may be found in MPAPS S-J-7.101-GS/PL. 2.0 DESIGN CONSI

6、DERATION: Conditions which impose a vibration component in a direction parallel to the axis of the pin should be avoided. Clevis pins are principally for use with clevises and are generally reusable without affecting holding action. Clevis pins are retained in place with split (cotter) pins. 3.0 MET

7、RIC-INCH RELATED SIZES: During the inch to metric design transition period, the following chart of related sizes can be used for reference. This information is not to be considered as a recommendation for substitutions but only as a means of determining approximate dimensional equivalents. Metric Se

8、ries Approximate mm Inch Series 5 3/16 6 1/4 8 5/16 10 3/8, 7/16 12 1/2 16 9/16, 5/8 20 3/4 4.0 PREFERRED LENGTHS: When standards for clevises are developed, preferred lengths for such use will be shown. When used elsewhere, it is recommended that diameter-length combinations be selected from the ch

9、art in the preferred parts section of 18.0. NUMBER: MPAPS S-JM-7.101-GS/PL TITLE: Clevis Pins - Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume al

10、l patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 4 5.0 COLOR CODING: Not recommended, except in cases where adequate insurance is needed to prevent mixing of “metric parts“ with look-alike “inch parts.“ The color blue is standard identifier used in some industries. This must be handled

11、 internally at individual plants where needed and is meant to be supplemental to the normal finish and easily deleted when the need for supplemental identification no longer exists. 6.0 METHOD OF DESIGNATION: Clevis pins will be designated on purchase orders by size, length, word description, materi

12、al, finish, and part number as follows: 6 x 20 mm, Clevis Pin, Hard, ZN6A, Part Number 7.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings. For new design, parts shall be sele

13、cted from “Approved“ part list only. Material: Steel, Case Hardened (hard) Finish: Zinc Trivalent, Class 6A (ZN6A), and Phosphate Coated (PHC) Nominal Sizes and Length Incrementation: Dimensions in millimeters: Nominal Length Diameters 5 6 8 10 12 16 20 10 X X 12 X X 16 X X X 20 X X X X 25 X X X X X

14、 30 X X X X X 35 X X X X X X 40 X X X X X X X 45 X X X X X X X 50 X X X X X X X 55 X X X X X X 60 X X X X X X 65 X X X X X 70 X X X X X 75 X X X X X 80 X X X X X 85 X X X X 90 X X X X 100 X X X X 110 X X X 120 X X X 130 X X 140 X X 150 X X 160 X X 170 X 180 X 190 X 200 X Note: Lengths over 200 mm wi

15、ll be in 20 mm increments. 8.0 TOLERANCES: Unless otherwise specified, tolerances on all dimensions are 0.25 mm. 9.0 HEADS: The top of head will be flat and either chamfered or rounded at outer periphery. 10.0 BEARING SURFACE: The bearing surface of the head will be flat and square with the axis of

16、pin (determined over a distance from under the head equivalent to 1.5 times the basic pin diameter) within 2 degrees. NUMBER: MPAPS S-JM-7.101-GS/PL TITLE: Clevis Pins - Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permissi

17、on from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 11.0 ECCENTRICITY: The head of pin will not be eccentric with axis of the shank of pin by an amount equal to more than 6 percent of the maximum head diameter or

18、0.25 mm whichever is greater. Eccentricity is defined as being one-half the full indicator movement (FIM). 12.0 HOLE ALIGNMENT AND ANGULARITY: The axis of hole through shank will not be offset from the axis of pin by more than 0.25 mm for the 5 and 6 nominal pin sizes, and 0.5 mm for all larger pin

19、sizes, and will be square with the axis of pin within 2 degrees. 13.0 MATERIAL: 0-201C steel per MPAPS A-0, Part II. 14.0 HEAT TREAT: Pins will be case hardened, Class 1, per CEMS A-40. 15.0 FINISHES: Pins will be furnished plain, plated or coated in accordance with the MPAPS and class listed below:

20、 Zinc Trivalent, Class 6A (ZN6A) MPAPS G-20, Class 6A. Phosphate Coating (PHC) MPAPS G-1, Class B-1. 16.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 17.0

21、WORKMANSHIP: Clevis pins will be free from burrs, loose scale, sharp edges and all other defects affecting their serviceability. 18.0 APPROVED PART SIZES: Dimensions in millimeters: Nominal A B C D E F G Recommended Split (Cotter) Pin Size or Basic Shank Diameter Head Height Head Diameter Hole Diame

22、ter End to Center Head Cham- Point Pin Ref fer Length Part Number Diameter Max Min Max Min Max Min Max Min Min Max Max Size Length 6 5.93 5.85 2.12 2 10.5 10 1.85 1.6 3.2 1 2 1.6 12 932951R1 10 9.92 9.83 4.15 4 18.5 18 3.5 3.2 4.5 1 2 3.2 20 934792R1 12 11.9 11.8 4.15 4 20.5 20 3.5 3.2 5.5 1.6 3 3.2

23、 20 934792R1 16 15.9 15.8 4.68 4.5 25.5 25 4.3 4 6 1.6 3 4 25 30243R1 Note: Min“ E“ dimension (distance from center line of hole to end of pin) is specified for calculating hole location from underside of head. NUMBER: MPAPS S-JM-7.101-GS/PL TITLE: Clevis Pins - Metric Series REVISION: 1506 This doc

24、ument is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 19.0 PART LIST: 19.1 Approved: Nominal Size Length Head To Hole Min

25、Finish Material Part Number 10 25 20.5 PHC HTS 30572R1 10 70 63.5 ZN6A HTS 40268R1 12 35 29.5 PHC HTS 30398R1 12 40 34.5 PHC HTS 30759R1 20.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/