NAVISTAR MPAPS S-JM-15 101-GS PL-2015 Cup Plugs - Metric Series (Noun Code - 6400).pdf

《NAVISTAR MPAPS S-JM-15 101-GS PL-2015 Cup Plugs - Metric Series (Noun Code - 6400).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS S-JM-15 101-GS PL-2015 Cup Plugs - Metric Series (Noun Code - 6400).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 4 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-JM-15.101-GS/PL Former Designation: ESP-JM-15.101-GS TITLE: Cup Plugs - Metric Series (Noun Code - 6400) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-JM-15.101-GS - April 2002 PRINTED COPIES O

3、F THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health pract

4、ices and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format; Combined GS, GI, PP. 1.0 GENERAL: Implementation of this standard must be in accordance with the policies and procedures outlined in MPAPS S-A-0.101. There may also be supplemental

5、group instructions in regard to use of metric standards that should be taken into account. This standard may differ in some respects with certain segments of national standards. In recognition of these differences, the sizes and tolerance ranges used were established in an effort to enable the use o

6、f commercially available items, dimensionally interchangeable worldwide. This specification contains the essentials of the following standards: German Institute of Standardization: DIN 443 2.0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this

7、 specification must comply with the requirements of the MPAPS B-50 specification. 3.0 METRIC-INCH RELATED SIZES: During the inch to metric design transition period, the following chart of related sizes can be used for reference. This information is not to be considered as a recommendation for substi

8、tutions but only as a means of determining approximate equivalents. Dimensions in millimeters: Metric Series Approximate mm Inch Series 8 5/16 10 3/8 12 1/2 14 9/16 16 5/8 18 11/16 20 3/4 22 7/8 25 1 28 1-1/8 32 1-1/4 36 1-7/16, 1-1/2 40 1-9/16 45 1-3/4 50 2 56 2-1/4 63 2-1/2 NUMBER: MPAPS S-JM-15.1

9、01-GS/PL TITLE: Cup Plugs -Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of 4 4.0

10、COLOR CODING: Not recommended, particularly with cup plugs, except in cases where adequate insurance is needed to prevent mixing of “metric parts“ with look-alike “inch parts.“ The color blue is standard identifier used in some industries. This must be handled internally at individual plants where n

11、eeded and is meant to be supplemental to the normal finish and easily deleted when the need for supplemental identification no longer exists. The supplemental blue color should not be used on finishes such as chromium bright which are specified for cosmetic purposes, or phosphate coating which may c

12、ause a loss of color identity. 5.0 METHOD OF DESIGNATION: Metric cup plugs will be designated on purchase orders by nominal size, word description, material, finish and part number as shown in the following examples: 10 mm, Tapered Cup Plug, STL, PHC, Part Number 16 mm, Tapered Cup Plug, SST, PLN, P

13、art Number 6.0 POLICY FOR SELECTING PARTS FOR NEW DESIGN: Approved parts are so designated to reduce variety of parts and assure maximum availability, interchangeability, and cost savings. For new design, parts shall be selected from “Approved“ part list only. Nominal Sizes: All shown Material: Carb

14、on steel (STL) Finish: Plain (PLN) 7.0 MATERIAL: Carbon steel per MPAPS A-0, Part II, Code 0-100. 8.0 NON-PREFERRED MATERIAL: Austenitic stainless steel (SST), standard with manufacturer (limited availability). 9.0 ASSEMBLY CONSIDERATIONS: Inasmuch as the end performance of these plugs is directly a

15、ffected by the adequacy of the holes into which they assemble and their proper insertion into same, the following data is included to provide the guidance in these areas. The recommended hole diameter limits specified will provide optimum assembly and performance to suit special conditions. However,

16、 deviations from these recommendations may be desirable to provide optimum assembly and performance to suit special conditions. To assure good sealing and plug retention, holes should be not more than 0.08 mm out of round and the surface roughness on walls over the sealing area should not exceed 2.5

17、 m AA. Satisfactory sealing may be achieved on somewhat rougher surfaces but plug retention capabilities will be reduced. To facilitate assembly and prevent scoring of plugs at insertion, it is recommended that entering edge of hole be relieved with as large a tangential radius as the wall thickness

18、 will permit. An alternative, although not preferred, is a countersink of 30 maximum included angle; to a minimum diameter 0.3 mm to 0.4 mm larger than the plug in its free state. The depth of the relief will be such as to permit open end of plugs to be inserted 0.25 mm minimum beyond the point of t

19、angency or intersection of countersink on wall of hole. 10.0 FINISH: Plain (PLN) or phosphate coated (PHC) standard with manufacturer. NUMBER: MPAPS S-JM-15.101-GS/PL TITLE: Cup Plugs -Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced w

20、ithout permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 4 11.0 INSTALLATION: Plugs should be driven from the inside bottom and not from the outer edge, or rim of the cup. This can best be accomplished by

21、use of a round arbor 0.5 mm to 0.6 mm smaller in diameter than the inside diameter of plug (A min - 2C max). The driving end is flat and perpendicular to axis of arbor with edge rounded to 1.5 mm radius. Where plugs are used in counterbored holes, care should be exercised in insertion to prevent the

22、 plug from bottoming on the shoulder of counterbore which could result in distortion of plug and loss of seal. Suitable lubricating oil is recommended wherever possible during installation of plugs to facilitate insertion and prevent galling. 12.0 WORKMANSHIP: Cup plugs must be free from burrs, loos

23、e scale, longitudinal scratches on coined surfaces and all other defects affecting their serviceability. 13.0 DIMENSIONS: Dimensions In millimeters: Nominal Plug Size A B C R1R 2D Outside Overall Stock Crown Corner Recommended Diameter Height Thickness Radius Radius Hole Diameter Max Min Nom Max Min

24、 Nom Max Min Nom Nom Min Max 8 8.16 8.1 3 3.3 2.7 0.75 0.81 0.69 20 1 8 8.04 10 10.16 10.1 3 3.3 2.7 0.75 0.81 0.69 25 1 10 10.04 12 12.22 12.13 4 4.38 3.62 1 1.07 0.93 30 1 12 12.04 14 14.22 14.13 5 5.38 4.62 1 1.07 0.93 35 1 14 14.04 16 16.22 16.15 5 5.38 4.62 1 1.07 0.93 40 1 16 16.04 18 18.22 18

25、.15 6 6.38 5.62 1 1.07 0.93 45 1 18 18.05 20 20.27 20.19 6 6.38 5.62 1 1.07 0.93 50 1 20 20.05 22 22.27 22.19 7 7.45 6.55 1.6 1.72 1.48 55 1.6 22 22.05 25 25.3 25.22 8 8.45 7.55 1.6 1.72 1.48 60 1.6 25 25.05 28 28.3 28.22 9 9.45 8.55 1.6 1.72 1.48 70 1.6 28 28.05 32 32.37 32.27 10 10.45 9.55 1.6 1.7

26、2 1.48 80 1.6 32 32.06 36 36.37 36.27 11 11.55 10.45 1.6 1.72 1.48 90 1.6 36 36.06 40 40.37 40.27 12 12.55 11.45 1.6 1.72 1.48 100 1.6 40 40.06 45 45.42 45.32 14 14.55 13.45 1.6 1.72 1.48 110 1.6 45 45.06 50 50.42 50.32 15 15.55 14.45 1.6 1.72 1.48 125 1.6 50 50.07 56 56.52 56.4 17 17.55 16.45 2 2.1

27、3 1.87 140 2.5 56 56.07 63 63.52 63.4 19 19.65 18.35 2 2.13 1.87 160 2.5 63 63.07 NUMBER: MPAPS S-JM-15.101-GS/PL TITLE: Cup Plugs -Metric Series REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards.

28、 Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 4 of 4 14.0 PART LIST: 14.1 Approved: 15.0 TECHNICAL INFORMATION: For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this sp

29、ecification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Nominal Size Finish Material Part Number 22 PLN STL 30452R1 25 PLN SST 31211R1 28 PLN SST 40098R1