EN ISO 28881-2013 en Machine tools - Safety - Electro-discharge machines《机床 安全性 电火花加工机械》.pdf

《EN ISO 28881-2013 en Machine tools - Safety - Electro-discharge machines《机床 安全性 电火花加工机械》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 28881-2013 en Machine tools - Safety - Electro-discharge machines《机床 安全性 电火花加工机械》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 28881:2013Machine tools Safety Electro-discharge machinesIncorporating corrigendum September 2013BS EN ISO 28881:2013National forewordThis British Standard is the UK implementation of EN ISO 28881:2013. It is identical to ISO 28881:2013, incorporating corrigendum S

2、eptember 2013. It supersedes BS EN 12957:2001+A1:2009 which is withdrawn.The start and finish of text introduced or altered by corrigendum is indicated in the text by tags. Text altered by ISO corrigendum September 2013 is indicated in the text by .The UK participation in its preparation was entrust

3、ed by Technical Committee MTE/1, Machine tools, to Subcommittee MTE/1/1, Machine tools - Safety.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are respo

4、nsible for its correctapplication. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 84373 0ICS 25.080.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of theStandard

5、s Policy and Strategy Committee on 31 August 2013.Amendments/corrigenda issued since publicationDate Text affected31 October 2013 Implementation of ISO corrigendum September 2013BRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 28881 August 2013 ICS 25.080.01 Supersedes EN 129

6、57:2001+A1:2009English Version Machine tools - Safety - Electro-discharge machines (ISO 28881:2013) Machines-outils - Scurit - Machines dlectro-rosion (ISO 28881:2013) Werkzeugmaschinen - Sicherheit - Funkenerodiermaschinen (ISO 28881:2013) This European Standard was approved by CEN on 14 March 2013

7、. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

8、 application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENEL

9、EC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy

10、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17,

11、 B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 28881:2013: EBS EN ISO 28881:2013EN ISO 28881:2013 (E) 3 Foreword This document (EN ISO 28881:2013) has been prepared by Technical Committee ISO/TC 39 “Machi

12、ne tools“ in collaboration with Technical Committee CEN/TC 143 “Machine tools - Safety” the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2014, and

13、conflicting national standards shall be withdrawn at the latest by February 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This

14、 document supersedes EN 12957:2001+A1:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an

15、integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Re

16、public of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 28881:2013 has been

17、approved by CEN as EN ISO 28881:2013 without any modification. BS EN ISO 28881:2013EN ISO 28881:2013 (E) 4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CE

18、N by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implement

19、ed as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations. WARNING Oth

20、er requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 28881:2013ISO 28881:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 34 List of s

21、ignificant hazards . 75 Safety requirements and/or protective measures 95.1 General requirements . 95.2 Safety-related parts of control systems for EDM equipment and EDM systems .105.3 Operating modes 115.4 Stop functions . 135.5 Specific requirements 146 Information for use .226.1 General 226.2 Mar

22、king, signs and written warnings . 226.3 Instruction handbook 22Annex A (informative) Examples and schematic diagrams 28Annex B (normative) Noise-emission measurements .37Annex C (informative) Fire protection codes for special regional cases 38Annex D (informative) Guidelines for risk assessment on

23、EDM equipment and EDM systems to identify the required performance level and, if necessary, category .48Bibliography .51BS EN ISO 28881:2013ISO 28881:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). Th

24、e work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gov

25、ernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.Th

26、e main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote

27、.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 28881 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 10, Safety.iv

28、 ISO 2013 All rights reservedBS EN ISO 28881:2013ISO 28881:2013(E)IntroductionThis International Standard has been prepared to be a Harmonized Standard to provide one means of conforming to the Essential Safety Requirements of the Machinery Directive of the European Union and associated EFTA regulat

29、ions.This document is a type-C standard as defined in ISO 12100:2010.The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the Scope of this International Standard. In addition, electro-discharge machining (EDM) equipment and EDM system

30、s are intended to be designed according to the principles of ISO 12100 for hazards which are not dealt with in this International Standard.When requirements of this type-C standard are different from those which are stated in type-A or -B standards, the requirements of this type-C standard take prec

31、edence over the requirements of other standards for machines that have been designed and built according to the requirements of this type-C standard.This International Standard defines performance level and safety categories of the safety-related parts of the control system for EDM equipment and EDM

32、 systems as defined in ISO 13849-1:2006.The requirements of this International Standard concern designers, manufacturers, suppliers and importers of machines described in the Scope.This International Standard also includes a list of informative items intended to be provided by the manufacturer to th

33、e user. ISO 2013 All rights reserved vBS EN ISO 28881:2013Machine tools Safety Electro-discharge machines1 ScopeThis International Standard specifies safety requirements and/or protective measures, applicable to EDM equipment and EDM systems, such as manually controlled EDM die sinking or EDM drilli

34、ng machines, numerically controlled EDM die sinking or EDM drilling machines, and numerically controlled EDM wire cutting machinesintended to be adopted by persons undertaking the design, construction, installation and/or supply of such equipment. This International Standard also includes informatio

35、n to be provided by the manufacturer to the user.This International Standard is not applicable to arc eroding and electro-chemical machining equipment.This International Standard takes account of the precondition of the intended use as well as the reasonably foreseeable misuse, in normal workshop en

36、vironments and non-explosive atmospheres, including transportation, installation, setting, maintenance, repair and dismantling for removal or disposal of EDM equipment and EDM systems.This International Standard is also applicable to auxiliary devices essential for EDM processing.This International

37、Standard deals with all significant hazards, hazardous situations or hazardous events relevant to EDM equipment and EDM systems, where they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This International Standard is intended

38、to apply to machines manufactured after the date of publication of this International Standard.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For undated references, the latest edition of the

39、referenced document (including any amendments) applies.ISO 3746, Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting planeISO 4413, Hydraulic fluid power General rules and

40、safety requirements for systems and their componentsISO 4414, Pneumatic fluid power General rules and safety requirements for systems and their componentsISO 4871, Acoustics Declaration and verification of noise emission values of machinery and equipmentISO 11202, Acoustics Noise emitted by machiner

41、y and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental correctionsISO/TR 11688-1, Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: PlanningISO 12100:2010, Safety o

42、f machinery General principles for design Risk assessment and risk reductionINTERNATIONAL STANDARD ISO 28881:2013(E) ISO 2013 All rights reserved 1BS EN ISO 28881:2013ISO 28881:2013(E)ISO 13849-1:2006, Safety of machinery Safety-related parts of control systems Part 1: General principles for designI

43、SO 13849-2:2003, Safety of machinery Safety-related parts of control systems Part 2: ValidationISO 13850, Safety of machinery Emergency stop Principles for designISO 13855, Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human bodyISO 13857:2008, Saf

44、ety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbsISO 14118, Safety of machinery Prevention of unexpected start-upISO 14122-1, Safety of machinery Permanent means of access to machinery Part 1: Choice of fixed means of access between two levelsISO 14122-

45、2, Safety of machinery Permanent means of access to machinery Part 2: Working platforms and walkwaysISO 14122-3, Safety of machinery Permanent means of access to machinery Part 3: Stairs, stepladders and guard-railsIEC 60204-1:2009, Safety of machinery Electrical equipment of machines Part 1: Genera

46、l requirementsIEC 60529, Degrees of protection provided by enclosures (IP Code)IEC 61000-6-2, Electromagnetic compatibility (EMC) Part 6-2: Generic standards Immunity for industrial environmentsIEC 61000-6-4, Electromagnetic compatibility (EMC) Part 6-4: Generic standards Emission standard for indus

47、trial environmentsIEC 61310-1, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signalsIEC 61310-2, Safety of machinery Indication, marking and actuation Part 2: Requirements for markingIEC 61558-1, Safety of power transformers, power suppli

48、es, reactors and similar products Part 1: General requirements and testsIEC 61800-5-2:2007, Adjustable speed electrical power drive systems Part 5-2: Safety requirements FunctionalEN 2, Classification of firesEN 54-1, Fire detection and fire alarm systems Part 1: IntroductionEN 349, Safety of machin

49、ery Minimum gaps to avoid crushing of parts of the human bodyEN 614-1, Safety of machinery Ergonomic design principles Part 1: Terminology and general principlesEN 614-2, Safety of machinery Ergonomic design principles Part 2: Interactions between the design of machinery and work tasksEN 626-1, Safety of machinery Reduction of risks to health from hazardous substances emitted by machinery Part 1: Principles and specifications for machinery manufacturersEN 95