EN 60317-22-2004 en Specifications for particular types of winding wires Part 22 Polyester or polyesterimide enamelled round copper wire overcoated with polyamide class 180 (Incor.pdf

《EN 60317-22-2004 en Specifications for particular types of winding wires Part 22 Polyester or polyesterimide enamelled round copper wire overcoated with polyamide class 180 (Incor.pdf》由会员分享，可在线阅读，更多相关《EN 60317-22-2004 en Specifications for particular types of winding wires Part 22 Polyester or polyesterimide enamelled round copper wire overcoated with polyamide class 180 (Incor.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60317-22:2004 Specifications for particular types of winding wires Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 ICS 26.060.10 +A1:2010 National foreword This British Standard is the UK implementation of EN 60317-22:2004+

2、A1:2010. It is identical to IEC 60317-22:2004, incorporating amendment 1:2009. It supersedes BS EN 60317-22:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee GEL/55, Winding wires. A list of organizations represented on this committee can be obtain

3、ed on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 60317-22:2004+A1:2010 This British Stand

4、ard was published under the authority of the Standards Policy and Strategy Committee on 13 December 2004 BSI 2010 Amendments/corrigenda issued since publication Date Comments 30 April 2010 Implementation of IEC amendment 1:2009 with CENELEC endorsement A1:2010; Text of Clause 23 replaced ISBN 978 0

5、580 67181 4EUROPEAN STANDARD EN 60317-22:2004+A1 NORME EUROPENNE EUROPISCHE NORM February 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B -

6、 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-22:2004 E ICS 26.060.10 Supersedes EN 60317-22:1995 + A1:1998English version Specifications for particular types of winding wires Part 22 : Polyester or pol

7、yesterimide enamelled round copper wire overcoated with polyamide, class 180 (IEC 60317-22:2004)Spcifications pour types particuliers de fils de bobinage Partie 22: Fil de section circulaire en cuivre maill avec polyester ou polyesterimide et avec surcouche polyamide, classe 180 (CEI 60317-22:2004)

8、Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten Teil 22: Runddrhte aus Kupfer, lackisoliert mit Polyester oder Polyesterimid und darber mit Polyamid, Klasse 180 (IEC 60317-22:2004) This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to comply with

9、 the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretaria

10、t or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the of

11、ficial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slov

12、enia, Spain, Sweden, Switzerland and United Kingdom. Foreword The text of document 55/910/FDIS, future edition 3 of IEC 60317-22, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-22 on 2004-09-01. This European Standard supe

13、rsedes EN 60317-22:1995 + A1:1998. The main changes with respect to EN 60317-22:1995 are as follows: new requirements for appearance, Subclause 3.2, added; breakdown voltage values, former Table 3, replaced with a reference to EN 60317-0-1; new pin hole test, Clause 23, added. The following dates we

14、re fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-09-01 Annex ZA has been added by CENEL

15、EC. _ Endorsement notice The text of the International Standard IEC 60317-22:2004 was approved by CENELEC as a European Standard without any modification. _ Foreword to amendment A1 The text of document 55/1124/CDV, future amendment 1 to IEC 60317-22:2004, prepared by IEC TC 55, Winding wires, was s

16、ubmitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60317-22:2004 on 2010-02-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying

17、 any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-11-01 latest date by which the national standards conflicting with the amendment ha

18、ve to be withdrawn (dow) 2013-02-01 _ Endorsement notice The text of amendment 1:2009 to the International Standard IEC 60317-22:2004 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 2 CONTENTS

19、INTRODUCTION.4 1 Scope.5 2 Normative references .5 3 Definitions and general notes on methods of test and appearance5 3.1 Definitions and general notes on methods of test 5 3.2 Appearance.6 4 Dimensions 6 5 Electrical resistance .6 6 Elongation 6 7 Springiness 6 8 Flexibility and adherence6 9 Heat s

20、hock .6 10 Cut-through 6 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,500 mm) .6 12 Resistance to solvents7 13 Breakdown voltage .7 14 Continuity of insulation .7 15 Temperature index .7 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat or solv

21、ent bonding8 19 Dielectric dissipation factor.8 20 Resistance to transformer oil8 21 Loss of mass 8 23 Pin hole test .8 30 Packaging 8 Table 1 Resistance to abrasion7 Annex ZA (normative) Normative references to international publications with their corresponding European publications .9 BS EN 60317

22、-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 3 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires Test methods (IEC 60851); 2) specifications for particular t

23、ypes of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 4 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 1 S

24、cope This part of IEC 60317 specifies the requirements of enamelled round copper winding wire of class 180 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all s

25、pecified wire requirements. The superimposed coating is based on polyamide resin. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 180 is a thermal class that requires a minim

26、um temperature index of 180 and a heat shock temperature of at least 200 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment inv

27、olved. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,050 mm up to and including 3,150 mm; grade 2: 0,050 mm up to and including 5,000 mm; grade 3: 0,250 mm up to and including 1,600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 603

28、17-0-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1, Spe

29、cifications for particular types of winding wires Part 0: General requirements Section 1: Enamelled round copper wire 3 Definitions and general notes on methods of test and appearance 3.1 Definitions and general notes on methods of test For definitions and general notes on methods of test, see Claus

30、e 3 of IEC 60317-0-1. In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 60317-22 shall prevail. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 5 3.2 Appearance See Clause 3 of IEC 60317-0-1. 4 Dimensions See Clause 4 of IEC 60317-0-1. 5 Electrical resistance See

31、Clause 5 of IEC 60317-0-1. 6 Elongation See Clause 6 of IEC 60317-0-1. 7 Springiness See Clause 7 of IEC 60317-0-1. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-1, where the constant K used for the calculation of the number of revolutions for the peel test shall be 110 mm. 9 Heat shock Se

32、e Clause 9 of IEC 60317-0-1, where the minimum heat shock temperature shall be 200 C. 10 Cut-through No failure shall occur within 2 min at 265 C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 2,500 mm) The wire shall meet the requirements given in Table 1.

33、 BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 6 Table 1 Resistance to abrasion Grade 1 Grade 2 Grade 3 Nominal conductor diameter mm Minimum average force to failure N Minimum force to failure of each measurement N Minimum average force to failure N Minimum force to failure of each

34、measurement N Minimum average force to failure N Minimum force to failure of each measurement N 0,250 0,280 0,315 0,355 0,400 2,85 3,10 3,35 3,60 3,85 2,45 2,60 2,80 3,05 3,25 4,70 5,05 5,45 5,85 6,25 4,00 4,30 4,60 4,95 5,30 5,80 6,25 6,70 7,20 7,70 4,90 5,30 5,70 6,10 6,50 0,450 0,500 0,560 0,630

35、0,710 4,15 4,45 4,75 5,10 5,45 3,50 3,75 4,05 4,35 4,65 6,75 7,20 7,70 8,25 8,85 5,70 6,10 6,50 7,00 7,50 8,25 8,85 9,50 10,20 10,90 7,00 7,50 8,05 8,65 9,25 0,800 0,900 1,000 1,120 1,250 5,85 6,30 6,75 7,35 7,90 4,95 5,35 5,75 6,20 6,70 9,50 10,20 10,90 11,60 12,50 8,05 8,60 9,20 9,80 10,50 11,70 1

36、2,50 13,30 14,20 15,20 9,90 10,60 11,30 12,00 12,90 1,400 1,600 1,800 2,000 2,240 8,50 9,20 9,95 10,60 11,70 7,20 7,80 8,40 9,00 9,90 13,30 14,30 15,40 16,40 17,50 11,30 12,10 13,00 13,90 14,80 16,40 17,60 13,90 14,90 2,500 12,80 10,80 18,60 15,80 For intermediate nominal conductor diameters, the va

37、lue of the next larger nominal conductor diameter shall be taken. 12 Resistance to solvents See Clause 12 of IEC 60317-0-1. 13 Breakdown voltage See Clause 13 of IEC 60317-0-1, where the elevated temperature shall be 180 C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-1. 15 Temperature i

38、ndex See Clause 15 of IEC 60317-0-1, where the minimum temperature index shall be 180. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 7 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric d

39、issipation factor Test inappropriate. 20 Resistance to transformer oil Test inappropriate. 21 Loss of mass Test inappropriate. 23 Pin hole test 30 Packaging See Clause 30 of IEC 60317-0-1. _ See Clause 23 of IEC 60317-0-1. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 8 Annex ZA (nor

40、mative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the

41、 referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-1 - 1)Specifications for particular types of winding wires Part 0-

42、1: General requirements - Enamelled round copper wire EN 60317-0-1 1998 2)1)Undated reference. 2)Valid edition at date of issue. BS EN 60317-22:2004+A1:2010 EN 60317-22:2004+A1:2010 (E) Page 9BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996

43、 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendm

44、ent or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard wou

45、ld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lat

46、est editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website h

47、ttp:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international sta

48、ndards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI

49、 are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via