DLA SMD-5962-90895 REV F-2011 MICROCIRCUIT LINEAR CHOPPER-STABILIZED OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

《DLA SMD-5962-90895 REV F-2011 MICROCIRCUIT LINEAR CHOPPER-STABILIZED OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90895 REV F-2011 MICROCIRCUIT LINEAR CHOPPER-STABILIZED OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 03 with vendor Cage 01295. Editorial changes throughout. 91-04-17 W. HECKMAN B Changes in accordance with NOR 5962-R330-92. 92-12-09 M. A. FRYE C Changes in accordance with NOR 5962-R017-97. 96-10-10 R. MONNIN D Incorporate NORs B

2、 and C and change the limit values under electrical performance characteristics for device type 04 under the supply voltage rejection ratio test. Updated boiler plate. lgt 99-09-03 R. MONNIN E Drawing updated to reflect current requirements. - ro 03-01-22 R. MONNIN F Update drawing as part of 5 year

3、 review. - jt 11-10-03 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV F F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmar

4、itime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, CHOPPER-STABILIZED, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DAT

5、E 90-07-27 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-90895 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E531-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OH

6、IO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are

7、 reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90895 01 M C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1

8、.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devi

9、ces meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 TLC2652 Precision chopp

10、er stabilized operational amplifier 02 TLC2654 Low noise chopper stabilized operational amplifier 03 TLC2652A Precision chopper stabilized operational amplifier 04 TLC2654A Low noise chopper stabilized operational amplifier 1.2.3 Device class designator. The device class designator is a single lette

11、r identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to M

12、IL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual in-line package G MACY1-X8 8 Metal can package P GDIP1-T8 or CDIP2-T8 8 Dual in-line package 2 CQCC1-N2

13、0 20 Square leadless chip carrier package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

14、RCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VDD+) . +8 V dc 2/ Supply voltage (VDD-) -8 V dc 2/ Differential input voltage . 16 V dc 3/ Input voltage range (VI) (any in

15、put) . 8 V dc 2/ Voltage on CLK IN and INT/ EXT pins VDD-to VDD-+5.2 V dc Input current (II) (each input) . 5 mA Output current (IO) 50 mA Duration of short circuit current at (or below) +25C Unlimited 4/ Current into CLK IN and INT/ EXT pins 5 mA Ambient temperature for 60 seconds: Case 2 . +260C L

16、ead temperature, soldering 1.6 mm (1/16 inch) from case for 60 seconds: Cases C, G, P +300C Power dissipation (TA +25C): Cases C and 2 1375 mW 5/ Case G . 650 mW 5/ Case P 1050 mW 5/ Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +150C 1.4 Recommended operat

17、ing conditions. Supply voltage (VDD) : Device types 01 and 03 . 1.9 V dc min to 8 V dc max Device types 02 and 04 . 2.3 V dc min to 8 V dc max Common-mode input voltage (VIC) : Device types 01 and 03 . VDD-min to VDD+- 1.9 V dc max Device types 02 and 04 . VDD-min to VDD+- 2.3 V dc max Clock input v

18、oltage VDD-to VDD-+5 V dc Ambient operating temperature range (TA) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltage values, except differential voltages, a

19、re with respect to the midpoint between VDD+and VDD-. 3/ Differential voltages are at the noninverting input with respect to the inverting input. 4/ The output may be shorted to either supply. Temperature or supply voltage or both must be limited to ensure that the maximum dissipation rating is not

20、exceeded. 5/ Above +25C derate at a factor of 11.0 mW/C for cases C and 2, 5.2 mW/C for case G, and 8.4 mW/C for case P. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, O

21、HIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of th

22、ese documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electr

23、onic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order De

24、sk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regula

25、tions unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modifica

26、tion in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions.

27、 The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The

28、 terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply ove

29、r the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without

30、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VDD= 5 V Group A subgroups Device type Limits Uni

31、t unless otherwise specified Min Max Input offset voltage 1/ VIOVIC= 0 V, RS= 50 1 01 3.5 V 2,3 10 1 02 20 2,3 50 1 03 3 2,3 8 1 04 10 2,3 40 Temperature coefficient 2/ of input offset voltage VIOVIC= 0 V, RS= 50 1,2,3 01,03 0.03 V/C 02,04 0.30 Input offset voltage 2/ long term drift VDVIC= 0 V, RS=

32、 50 , 1 01,02 0.06 V/mo TA= +25C 03,04 0.02 Input offset current IIOVIC= 0 V, RS= 50 , TA= -55C, +125C 2,3 01,02,03,04 500 pA Input bias current IIBVIC= 0 V, RS= 50 , TA= -55C, +125C 2,3 01,02,03,04 500 pA Common mode input voltage range VICRRS= 50 1,2,3 01,03 -5 to 3.1 V 02,04 -5 to 2.7 Maximum pos

33、itive peak output voltage swing VOM+RL= 10 k 3/ 1,2,3 01,02,03,04 4.7 V Maximum negative peak output voltage swing VOM-RL= 10 k 3/ 1,2,3 01,02,03,04 -4.7 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC

34、IRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VDD= 5 V Group A subgroups Device type Limits Unit unless otherwise specifie

35、d Min Max Large signal differential voltage amplification AVDVO= 4 V, RL= 10 k 1,2,3 01,02 120 dB 1 03,04 135 2,3 120 Clamp on-state current ICONVO= -5 V to +5 V 1,2,3 01,02,03,04 25 A Clamp off-state current ICOFFRL= 100 k 1 01,02,03,04 100 pA 2,3 500 Common mode rejection ratio CMRR VO= 0 V, RS= 5

36、0 , 1,2,3 01,03 120 dB VIC= VICRmin 02 105 04 110 Supply voltage rejection ratio kSVRVDD+= 1.9 V to 8 V, VO= 0 V, RS= 50 1,2,3 01,03 120 dB (VDD/ VIO) VDD+= 2.3 V to 8 V, 1 02 110 VO= 0 V, RS= 50 2,3 105 1 04 110 2,3 110 Supply current IDDVO= 0 V, no load 1 All 2.4 mA 2,3 2.5 See footnotes at end of

37、 table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Con

38、tinued. Test Symbol Conditions -55C TA +125C VDD= 5 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Positive slew rate at unity gain SR+ VO= 2.3 V, RL= 10 k, 4 01,03 2 V/s CL= 100 pF 5,6 1.3 4 02,04 1.5 5,6 1.1 Negative slew rate at unity gain SR- VO= 2.3 V, RL= 10 k,

39、4 01,03 2.3 V/s CL= 100 pF 5,6 1.6 4 02,04 2.3 5,6 1.3 Equivalent input noise 2/ voltage VNF = 10 Hz, TA= +25C 4 01,03 140 nV / Hz 02,04 75 F = 1 kHz, TA= +25C 01,03 35 02,04 20 1/ Subgroups 1, 2, and 3 of this parameter are guaranteed by design. Thermocouple effects preclude measurement of these vo

40、ltages in high speed automatic testing. VIOis measured to a limit determined by the test equipment capacity. 2/ Not production tested. 3/ Output clamp is not connected. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ

41、E A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 Device types 01, 02, 03, 04 Case outlines C G and P 2 Terminal number Terminal symbol 1 CXB CXA NC 2 CXA IN- CXB 3 NC IN+ CXA 4 IN- VDD-NC 5 IN+ CLAMP NC 6 NC OUT IN- 7 VDD-VDD+NC 8 C RETURN

42、 CXB IN+ 9 CLAMP - NC 10 OUT - VDD-11 VDD+- NC 12 CLK OUT - C RETURN 13 CLK IN - CLAMP 14 INT / EXT - OUT 15 - - NC 16 - - VDD+17 - - NC 18 - - CLK OUT 19 - - CLK IN 20 - - INT / EXT NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitt

43、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90895 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 9 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marke

44、d. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in a

45、ccordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be

46、 a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate

47、of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the ma

48、nufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with ea