BS ISO 9738-2001 Turnbarrels for aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用旋转套筒 尺寸及载荷》.pdf

《BS ISO 9738-2001 Turnbarrels for aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用旋转套筒 尺寸及载荷》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9738-2001 Turnbarrels for aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用旋转套筒 尺寸及载荷》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS ISO 9738:2000 Turnbarrels, for aircraft control wire rope Dimensions and loads ICS 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 9738:2000 This British Standard, having been prepared under the direction of the Engineering Sec

2、tor Committee, was published under the authority of the Standards Committee and comes into effect on 15 March 2001 BSI 03-2001 ISBN 0 580 35045 2 National foreword This British Standard reproduces verbatim ISO 9738:2000 and implements it as the UK national standard. The UK participation in its prepa

3、ration was entrusted to Technical Committee ACE/14, Aerospace details and parts, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications refer

4、red to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a c

5、ontract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the inte

6、rpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 t

7、o 5 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsA Referencenumbe r ISO9738:2000 (E) INTERNATIONAL STANDARD ISO 9738 Firstedition 20001215 AerospaceTurnbarrels,foraircraft co

8、ntrolwireropeDimensionsandloads AronautiqueetespaceDouillesdetendeursdecblesdecommande daronefsDimensionsetchargesISO9738:2000(E) iiISO9738:2000(E) iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInte

9、rnationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakepartinthework.ISOcollabor

10、atescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting.

11、PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO9738waspreparedbyTechnicalCommitteeISO/TC20, Aircraftandspacevehicles, SubcommitteeSC12, Mechanicalsystemparts . AnnexAformsanormativepartofthisInternationalStandard.INTERNATIONALST

12、ANDARD OISO9738:2000(E) 1 AerospaceTurnbarrels,foraircraftcontrolwirerope Dimensionsandloads 1Scope ThisInternationalStandardspecifiesthecharacteristicsofturnbarrelsforaircraftcontrolwireropeineitherlowalloy steel,corrosionresistantsteel,copperzincalloyoraluminiumalloy. 2Normative references Thefoll

13、owingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthis InternationalStandard.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.However,partiestoagreementsbasedonthisInternationalStandardareencouragedtoinvestigatethe

14、 possibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.Forundatedreferences, thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersof currentlyvalidInternationalStandards. ISO4262:1983, WroughtcopperzincalloysChemicalcompositionandformso

15、fwroughtproductsPart2: Leadedcopperzincalloys. ISO1637:1987, WroughtcopperandcopperalloysrodandbarTechnicalconditionsofdelivery. ISO20201:1997, Aerospace Preformedflexiblesteelwireropeforaircraftcontrols Part 1:Dimensionsand loads. ISO58552:1988, AerospaceconstructionMJthreadsPart2:Limitdimensionsfo

16、rboltsandnuts. ISO8074:1985, AerospaceSurfacetreatmentofausteniticstainlesssteelparts. ISO9761:2000, Aerospace Loc kingc lips,inc orrosion resistants teel,for air craftc ontrolwir er opetur nbuckles Dimensions. ISO10955:1999, AerospaceEndfittingsandturnbarrelsforaircraftcontrolwireropeTechnicalspeci

17、fication . ISO13715:2000, TechnicaldrawingsEdgesofundefinedshapeVocabularyandindicationondrawings. EN2101, AerospaceseriesChromicacidanodizingofaluminiumandwroughtaluminiumalloys. EN2133:1998, Aerospaces eriesCadmiumplatingofs teelswiths pecifiedtens iles trength 1450MPa, copper, copperalloysandnick

18、elalloys. EN2284, AerospaceseriesSulphuricacidanodizingofaluminiumandwroughtaluminiumalloys. EN2704: 1) , AerospaceseriesAluminiumalloy2024T3511Barsa 75mm. 2) EN3487: 1) ,AerospaceseriesSteelFEPA3601Softened500MPa R m 700MPa Barsfor machining D e 100mm. 2) 1) Tobepublished. 2) AECMA.ISO9738:2000(E)

19、2 SAEAMS2431/6A, PeeningMedia,GlassShot. SAEAMS4339, AluminiumAlloy,RolledorColdFinishedBarsandRods4.4Cu1.5Mg0.60Mn,SolutionHeat Treated,ColdWorked,andArtificiallyAged. SAEAMS5635D, Steel,CorrosionResistant,Bars,WireandF orgings18Cr9Ni0.21PbF reeMachining,Solution HeatTreated. SAEAMS6370K, SteelBars

20、,Forgings,andRings0.95Cr0.20Mo(0.280.33C). MILA8625, Anodiccoatings,foraluminiumandaluminiumalloys. 3) QQP416F, Plating,Cadmium(Electrodeposited). 3) 3 Configuration,dimensions,loadsandmasses Configuration,dimensions,loadsandmassesshallbeinaccordancewithFigure1andTable1. 4Material CodeA:corrosionres

21、istantsteel(inaccordancewithannexA). CodeB:copperzincalloyinaccordancewithISO4622andISO1637(inaccordancewithannexA). CodeC:aluminiumalloy(inaccordancewithannexA). CodeD:lowalloysteel(inaccordancewithannexA). 5Surface treatment Corrosionresistantsteel:passivation(codeP)inaccordancewithISO8074orpeenin

22、g(codeG)(inaccordance withannexA). Copperzincalloy:nosurface(codeN)treatmentorpeening(codeG)(inaccordancewithannexA). Aluminiumalloy:anodicoxydation(codeA)(inaccordancewithannexA). Lowalloysteel:cadmiumplating(inaccordancewithannexA). 3) Maybeobtainedfrom:DODSSPCustomerService,DefensePrintingService

23、DetachmentOffice,Building4D,700Robbions Ave.,Philadelphia,PA191115094,USA.ISO9738:2000(E) 3 Dimensionsinmillimetres Surfaceroughnessinmicrometres a Threadonleft b Imperfectthread c Threadonright d Pitchdiameter e Marking f Depthofcountersunk0,4mmto0,8mm g Groovemarkingthreadonleft h Slotforlockingcl

24、ipinaccordancewithISO9761(Code04turnbarrelshaveasingleslot) Figure1ISO9738:2000(E) 4 Table1 Dimensionsinmillimetres Thread a D 1 D 2 D 3 D 4 L 1 L 2 L 3 L 4 P Mass b Minimum breakingload c Nominaldiameter ofwirerope c Code Designation h11 0 1 + -03 0 , min. max. Code 0,5 min. 0,25 0,8 min. max. g/pi

25、ece kN 04 MJ4 0,74H6H 7 5,5 5,2 4,18 4,78 S 44 20 4 4,36 4,45 5,3 2,15 1,6 05 MJ5 0,84H6H 9 6,8 6,2 5,2 5,8 S 54 25 5 5,29 5,49 9,4 4,45 2,4 L 84 40 14,2 06 MJ6 14H6H 11 8,5 7,5 6,24 7,04 S 64 30 8 6 6,16 6,36 18,3 8,9 3,2 L 100 48 28 07 MJ7 14H6H 12 9,8 8,8 7,24 8,04 S 74 35 7 7,16 7,36 26,3 12,45

26、4 L 114 55 40,1 08 MJ8 14H6H 13 11,5 10,5 8,24 9,04 S 85 40 8 8,16 8,36 41,4 18,6 4,8 10 MJ10 1,254H6H 15 13,5 12 10,28 11,08 S 110 52 10 10 9,83 10,04 69 24,9 5,6 12 MJ12 1,254H6H 17 15,8 14 12,29 13,09 S 12 11,83 12,04 89,3 31,2 6,4 a InaccordancewithISO58552. b Forturnbarrelsincorrosionresistants

27、teel. c InaccordancewithISO20201. 6Designation EachturnbarrelinaccordancewiththisInternationalStandardshallbedesignatedasshowninthefollowing example. EXAMPLE 7Marking ThemarkingpositionshallbeinaccordancewithFigure1. Inadditiontothemanufacturersownmarking,eachturnbarrelinaccordancewiththisInternatio

28、nalStandardshall bemarkedusingtheidentityblockspecifiedinclause6. Themarkingmethodisatthemanufacturersoption. 8Technical specification InaccordancewithISO10955.ISO9738:2000(E) 5 AnnexA (normative) Correspondencebetweennationalstandards Thisannexestablishesacorrespondencebetweendifferentmaterialsands

29、urfacetreatmentstandardsfromcertain usercountries.Othermemberbodiesareinvitedtodeclaretheirmaterialsandsurfacetreatmentstandardsinthis annex. ThematerialsandprocessescitedinTables A.1andA.2areconsideredtobeequivalent,assumingthatthe requirementsforturnbarrelsspecifiedinthisInternationalStandardarere

30、spected. TableA.1Europeanstandards Code Material Surfacetreatment Family Standard Nature Standard A Corrosionresistantsteel EN3487 Passivation ISO8074 Peening SAEAMS2431/6A B Copperzincalloy ISO4622 Nosurfacetreatment ISO1637 Peening SAEAMS2431/6A C Aluminiumalloy EN2704 Anodicoxydation EN2101orEN22

31、84 D Lowalloysteel EN2207 Cadmiumplating EN2133 TableA.2U.S.standards Code Material Surfacetreatment Family Standard Nature Standard A Corrosionresistingsteel SAEAMS5635 Passivation ISO8074 Peening SAEAMS2431/6A B Copperzincalloy ISO4622 Nosurfacetreatment ISO1637 Peening SAEAMS2431/6A C Aluminiumal

32、loy SAEAMS4339 Anodicoxydation MILA8625 TypeII,Class1 D Lowalloysteel SAEAMS6370 Cadmiumplating QQP416 TypeII,Class2BS ISO 9738:2000 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It present

33、s the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI t

34、o improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000.

35、 Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Te

36、l: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Informat

37、ion on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the

38、 Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002.

39、 Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrigh

40、t, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the sta

41、ndard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.