BS ISO 9737-2001 Eye-ends in corrosion resisting steel swaged on aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用锻制耐腐蚀钢有眼端 尺寸及载荷》.pdf

《BS ISO 9737-2001 Eye-ends in corrosion resisting steel swaged on aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用锻制耐腐蚀钢有眼端 尺寸及载荷》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9737-2001 Eye-ends in corrosion resisting steel swaged on aircraft control wire rope - Dimensions and loads《航空器操纵钢丝绳用锻制耐腐蚀钢有眼端 尺寸及载荷》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS ISO 9737:2000 Eye-ends, in corrosion resisting steel, swaged on aircraft control wire rope Dimensions and loads ICS 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 9737:2000 This British Standard, having been prepared under the

2、 direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 March 2001 BSI 03-2001 ISBN 0 580 35040 1 National foreword This British Standard reproduces verbatim ISO 9737:2000 and implements it as the UK national standard.

3、The UK participation in its preparation was entrusted to Technical Committee ACE/14, Aerospace details and parts, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement

4、 international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include al

5、l the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European co

6、mmittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii

7、 and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsA Referencenumbe r ISO9737:2000 (E) INTERNATIONAL STANDARD ISO 9737 Fi

8、rstedition 20001215 AerospaceEyeends,incorrosion resistantsteel,swagedonaircraftcontrol wireropeDimensionsandloads AronautiqueetespaceEmboutsil,enacierrsistantlacorrosion, sertirsurcbledecommandedaronefsDimensionsetchargesISO9737:2000(E) iiISO9737:2000(E) iii Foreword ISO(theInternationalOrganizatio

9、nforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.I

10、nternationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirective

11、s,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO9737waspreparedbyTechnicalCommitteeISO/TC20, Aircraftandspacevehicles, Su

12、bcommitteeSC12, Mechanicalsystemparts . AnnexAformsanormativepartofthisInternationalStandard.INTERNATIONALSTANDARD OISO9737:2000(E) 1 AerospaceEyeends,incorrosionresistantsteel,swagedon aircraftcontrolwireropeDimensionsandloads 1Scope ThisInternationalStandardspecifiesthecharacteristicsofeyeendsinco

13、rrosionresistantsteelswagedonaircraft controlwirerope. 2Normative references Thefollowingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthis InternationalStandard.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.Howe

14、ver,partiestoagreementsbasedonthisInternationalStandardareencouragedtoinvestigatethe possibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.Forundatedreferences, thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersof currentlyvalidInter

15、nationalStandards. ISO20201:1997, Aerospace Preformedflexiblesteelwireropeforaircraftcontrols Part 1:Dimensionsand loads. ISO8074:1985, AerospaceSurfacetreatmentofausteniticstainlesssteelparts. ISO10955:1999, AerospaceEndfittingsandturnbarrelsforaircraftcontrolwireropeTechnicalspecification . ISO137

16、15:2000, TechnicaldrawingsEdgesofundefinedshapeVocabularyandindicationondrawings. EN2465: 1) , AerospaceseriesSteelFEPA11SoftenedBars D e 100mm . 2) SAEAMS2431/6A, PeeningMedia,GlassShot . SAEAMS5639G, Steel,CorrosionResistant,Bars,Wire,Forgings,TubingandRings,19Cr10Ni,SolutionHeat Treated. SAEAMS56

17、41F, Steel,CorrosionResistant,Bars,Wire,andForgings,18.5Cr10Ni0.22SeFreeMachining; SwagingorUpsetting,SolutionHeatTreated. 3 Configuration,dimensions,loadsandmasses Configuration,dimensions,loadsandmassesshallbeinaccordancewithFigure1andTable1. 4Material Corrosionresistantsteel(inaccordancewithannex

18、A). 1) Tobepublished. 2) AECMA.ISO9737:2000(E) 2 Dimensionsinmillimetres Surfaceroughnessinmicrometres a Marking Figure1ISO9737:2000(E) 3 Table1 Dimensionsinmillimetres Wirerope Minimum Code Nominal D 1 b D 2 D 3 D 4 D 5 D 6 EHL 1 L 2 L 3 L 4 RT Mass breaking diameter a g/piece load a - + 025 06 , ,

19、 H8 -012 0 , 0 012 + , 0 025 + , -015 0 , h11 0 025 + , 0,5 0,5 0,5 0 1 + 0 1 + kN 16 1,6 10 4,1 1,9 2,3 3,5 2,5 42 11 13 26 3 0,04 4,7 2,15 24 2,4 12 5 5,6 2,8 3,0 4,8 3 1 52 15,5 18 32 0,05 9,7 4,45 32 3,2 14 6,4 3,6 3,9 5,6 5 61 16 19 39 5 0,08 17,6 8,9 40 4 17 6 7,5 4,4 4,8 6,4 6 69 17,5 21 45 2

20、7,7 12,45 48 4,8 20 8 9,1 5,2 5,6 8 6,5 77 18,5 23 51 6 41,4 18,6 56 5,6 23 10,9 6 6,5 9,5 7,5 1,5 85 20 25 57 8 0,10 67,1 24,9 64 6,4 25 10 12,6 6,8 7,4 11 8 96 23,5 29 64 93,2 31,2 a InaccordancewithISO20201. b Afaultintheshapeofthesphericalsurfaceofradius D 1 /2ispermittedwithinthelimitsofthelimi

21、tdeviationvaluefor D 1 . 5Surface treatment Passivation(codeP)inaccordancewithISO8074orpeening(codeG)(in accordancewith annexA). 6Designation EacheyeendinaccordancewiththisInternationalStandardshallbedesignatedasshowninthefollowingexample. EXAMPLE 7Marking ThemarkingpositionshallbeinaccordancewithFi

22、gure1. Inadditiontothemanufacturersownmarking,eachendfittinginaccordancewiththisInternationalStandardshall bemarkedusingtheidentityblockspecifiedinclause6. Themarkingmethodisatthemanufacturersoption. 8Technical specification InaccordancewithISO10955.ISO9737:2000(E) 4 AnnexA (normative) Correspondenc

23、ebetweennationalstandards Thisannexestablishesacorrespondencebetweendifferentmaterialsandsurfacetreatmentstandardsfromcertain usercountries.Othermemberbodiesareinvitedtodeclaretheirmaterialsandsurfacetreatmentstandardsinthis annex. ThematerialsandprocessescitedinTables A.1andA.2areconsideredtobeequi

24、valent,assumingthatthe requirementsforendfittingsspecifiedinthisInternationalStandardarerespected. TableA.1Europeanstandards Material Surfacetreatment Family Standard Nature Standard Corrosionresistantsteel EN2465 Passivation ISO8074 Peening SAEAMS2431/6A TableA.2U.S.standards Material Surfacetreatm

25、ent Family Standard Nature Standard Corrosionresistantsteel SAEAMS5639 or Passivation ISO8074 SAEAMS5641 Peening SAEAMS2431/6ABS ISO 9737:2000 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards.

26、It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant ai

27、m of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020

28、8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Se

29、rvices. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested

30、. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. C

31、ontact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020

32、8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under th

33、e Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementi

34、ng the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.