DLA MIL-DTL-3922 67 E-2013 FLANGES WAVEGUIDE (CONTACT) (ROUND 4 HOLE) (MILLIMETER).pdf

《DLA MIL-DTL-3922 67 E-2013 FLANGES WAVEGUIDE (CONTACT) (ROUND 4 HOLE) (MILLIMETER).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3922 67 E-2013 FLANGES WAVEGUIDE (CONTACT) (ROUND 4 HOLE) (MILLIMETER).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-3922/67E 17 September 2013 SUPERSEDING MIL-DTL-3922/67D 3 December 2009 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (CONTACT) (ROUND, 4 HOLE) (MILLIMETER) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for ac

2、quiring the flanges described herein shall consist of this specification sheet and MIL-DTL-3922. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for general information only (1 inch = 25.4 mm). 3. This requirement is not applicable to dash numbers 001, 002, or 003. 4. See table I for l

3、ettered dimensions. FIGURE 1. Flange. AMSC N/A FSC 5985Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Flange dimensions. 1/ Metric equivalents are in parentheses. 2/ Material shall be copper alloy. 3/ Material shall be aluminum alloy. PIN M

4、3922/67- PIN M3922/67- Dimensions 1/ A +.002 (+ 0.05) -.000 B +.002 (+ 0.05) -.000 C + 0.00 -.002 (- 0.05) D .005 ( 0.13) E .005 ( 0.13) F BSC G .005 (0.13) H .005 (0.13) J9 Dash no. 2/ Used with Dash no. 3/ Used with Waveguide Mating flange Waveguide Mating flange 001 M85/3-010 (RG-97/U), 011, 012

5、(RG-272/U) M3922/67- 001 - - - .309 (7.85) .197 (5.00) 1.125 (28.58) .406 (10.31) .406 (10.31) .9375 (23.812) .268 (6.81) .042 (1.07) .156 (3.96) .005 (0.13) 002 M85/3-017(RG-98/U), 018, 019 (RG-273/U) M3922/67- 002 - - - .233 (5.92) .159 (4.04) .750 (19.05) .328 (8.33) .328 (8.33) .5625 (14.288) .2

6、68 (6.81) .030 (0.76) .156 (3.96) .005 (0.13) 003 M85/3-020(RG-99/U), 021, 022 (RG-274/U) M3922/67- 003 - - - .207 (5.26) .146 (3.71) .750 (19.05) .296 (7.52) .296 (7.52) .5625 (14.288) .268 (6.81) .030 (0.76) .156 (3.96) .005 (0.13) 004 M85/1-100,102(RG-53/U), 106 (RG-66/U) M3922/67- 004 011 M85/1-

7、103 (RG-121/U), 104 M3922/ 67-011 .502 (12.75) .252 (6.40) 1.125 (28.58) .625 (15.88) .625 (15.88) .9375 (23.812) .250 (6.35) .032 (0.81) .160 (4.06) +.005 (.13) -.002 (.05) 005 M85/3-006(RG-96/U), 007, 008 (RG-271/U) M3922/67- 005 012 M85/3-009 M3922/ 67-012 .362 (9.19) .222 (5.64) 1.125 (28.58) .5

8、00 (12.70) .468 (11.89) .9375 (23.812) .250 (6.35) .032 (0.81) .160 (4.06) +.005 (.13) -.002 (.05) 006 M85/3-010(RG-97/U), 011, 012 (RG-272/U) M3922/67- 006 013 M85/3-013 M3922/ 67-013 .306 (7.77) .194 (4.93) 1.125 (28.58) .500 (12.70) .468 (11.89) .9375 (23.812) .250 (6.35) .032 (0.81) .160 (4.06)

9、+.005 (.13) -.002 (.05) 007 M85/3-014, 015, 016 (RG-358/U) M3922/67- 007 - - - .270 (6.86) .176 (4.47) 1.125 (28.58) .500 (12.70) .468 (11.89) .9375 (23.812) .250 (6.35) .032 (0.81) .160 (4.06) +.005 (.13) -.002 (.05) 008 M85/3-017 (RG-98/U), 018, 019 (RG-273/U) M3922/67- 008 - - - .230 (5.84) .156

10、(3.96) .750 (19.05) .375 (9.53) .312 (7.92) .5625 (14.288) .250 (6.35) .032 (0.81) .160 (4.06) +.005 (.13) -.002 (.05) 009 M85/3-020 (RG-99/U), 021, 022 (RG-274/U) M3922/67- 009 - - - .204 (5.18) .143 (3.63) .750 (19.05) .375 (9.53) .312 (7.92) .5625 (14.288) .250 (6.35) .032 (0.81) .160 (4.06) +.00

11、5 (.13) -.002 (.05) 010 M85/3-023, 024, 025 (RG-359/U) M3922/67- 010 - - - .182 (4.62) .132 (3.35) .750 (19.05) .375 (9.53) .312 (7.92) .5625 (14.288) .250 (6.35) .032 (0.81) .160 (4.06) +.005 (.13) -.002 (.05) MIL-DTL-3922/67E2Provided by IHSNot for ResaleNo reproduction or networking permitted wit

12、hout license from IHS-,-,-MIL-DTL-3922/67E 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for general information only (1.00 inch = 25.4 mm). FIGURE 2. Socket-head cap screw. REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Material: Flange: See table I. Cap scr

13、ew: Corrosion resistant steel in accordance with SAE-AMS-QQ-S-763, type 302 or 304. Marking: See figure 1. Part or Identifying Number (PIN): M3922/67-(dash number from table I). Material supplied with flange: Four socket-head cap screws as specified in figure 2. ENGINEERING INFORMATION: Finished fla

14、nge and waveguide assembly (dash numbers 004 through 013 only): See figure 3 and table II. Cross reference and supersession data, frequency range, and return loss data: See table III. Inches mm .002 .005 .010 .078 .110 .112 .180 .300 .400 0.05 0.13 0.25 1.98 2.79 2.84 4.57 7.62 10.16 Provided by IHS

15、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/67E 4 Inches mm Inches mm Inches mm .0005 .001 .002 .003 .004 .005 0.013 0.03 0.05 0.08 0.10 0.13 .015 .030 .0600 .0615 .067 .112 0.38 0.76 1.524 1.562 1.70 2.84 .130 .140 .156 .160 .250 .312 3.30 3.56 3.

16、96 4.06 6.35 7.92 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only based upon 1.00 inch = 25.4 mm. 3. See table II for lettered dimensions. FIGURE 3. Finished flange and waveguide assembly. Provided by IHSNot for ResaleNo reproduction or networking per

17、mitted without license from IHS-,-,-MIL-DTL-3922/67E 5 TABLE II. Finished flange and waveguide assembly dimensions (004 through 013 only). PIN M3922/67- Dimensions 1/ K .0015 (0.038) L .0015 (0.038) M +.000 -.002 -0.05 N BSC T .005 (0.13) U .005 (0.13) 004, 011 .4200 (10.668) .1700 (4.318) 1.125 (28

18、.58) .9375 (23.812) .625 (15.88) .625 (15.88) 005, 012 .2800 (7.112) .1400 (3.556) 1.125 (28.58) .9375 (23.812) .500 (12.70) .468 (11.89) 006, 013 .2240 (5.690) .1120 (2.845) 1.125 (28.58) .9375 (23.812) .500 (12.70) .468 (11.89) 007 .1880 (4.775) .0940 (2.388) 1.125 (28.58) .9375 (23.812) .500 (12.

19、70) .468 (11.89) 008 .1480 (3.759) .0740 (1.880) .750 (19.05) .5625 (14.288) .375 (9.53) .312 (7.92) 009 .1220 (3.099) .0610 (1.549) .750 (19.05) .5625 (14.288) .375 (9.53) .312 (7.92) 010 .1000 (2.540) .0500 (1.270) .750 (19.05) .5625 (14.288) .375 (9.53) .312 (7.92) 1/ Metric equivalents are in pa

20、rentheses. TABLE III. Suggested frequency range, cross reference, supersession data, and return loss data. PIN M3922/67- AN nomenclature Frequency range Worst case return loss (dB) Lowest frequency Highest frequency 001 002 003 004 005 006 1/ 007 2/ 008 009 010 011 012 013 UG-383/U UG-385/U UG-387/U

21、 - - - - - - - - - - GHz 33.0 - 50.0 50.0 - 75.0 60.0 - 90.0 18.0 - 26.5 26.5 - 40.0 33.0 - 50.0 40.0 - 60.0 50.0 - 75.0 60.0 - 90.0 75.0 - 110.0 18.0 - 26.5 26.5 - 40.0 33.0 - 50.0 -29.6 -22.4 -18.8 -55.1 -48.7 -43.7 -41.4 -36.5 -32.9 -30.1 -55.1 -48.7 -43.7 -36.3 -28.9 -25.4 -61.2 -54.2 -50.3 -47.

22、4 -43.0 -39.5 -36.1 -61.2 -54.2 -50.3 1/ Supersedes M3922/65-001. 2/ Supersedes M3922/65-002. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/67E 6 Referenced documents: In addition to MIL-DTL-3922, this specification sheet also referenc

23、es: SAE-AMS-QQ-S-763 The margins of this specification sheet are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contrac

24、tors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2013-025) DLA - CC Review activit

25、ies: Army - AR, CR4, MI Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-