DIN EN ISO 14663-1-2006 Plastics - Ethylene vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 14663-1 1.pdf

《DIN EN ISO 14663-1-2006 Plastics - Ethylene vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 14663-1 1.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 14663-1-2006 Plastics - Ethylene vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 14663-1 1.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 DEUTSCHE NORM June 2006DIN EN ISO 14663-1 ICS 83.080.20 Plastics Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 14663-1:1999) English version of DIN EN ISO 14663-1:2006-06 Kunststoffe Ethylen-Vinylalkohol (EVOH)-

2、Copolymer-Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 14663-1:1999) Englische Fassung DIN EN ISO 14663-1:2006-06 Document comprises 10 pages No part of this standard may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verla

3、g GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 8 www.din.de www.beuth.de !,o9E“11.06 9762234DIN EN ISO 14663-1:2006-06 2 National foreword This standard has been published in accordance with a decision taken by CEN/TC 249 to adop

4、t, without alteration, International Standard ISO 14663-1 as a European Standard. The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Technical Committee NA 054-02-08 AA Sonstige Thermoplast-Formmassen. Most of the International

5、 Standards listed in clause 2 have been revised since the publication of ISO 14663-1 in 1999 and have been adopted as European Standards. For each standard cited, users should check whether a more current edition can be used without restrictions. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN I

6、SO 14663-1 April 2006 ICS 83.080.20English Version Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 14663-1:1999) Plastiques - Matriaux base de copolymres thylne/alcool vinylique (EVOH) pour moulage et

7、extrusion - Partie 1: Systme de dsignation et base de spcification (ISO 14663-1:1999) Kunststoffe - Ethylen-Vinylalkohol (EVOH)-Copolymer-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 14663-1:1999) This European Standard was approved by CEN on 16 March 2006. CEN members a

8、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

9、the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same sta

10、tus as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia

11、, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide fo

12、r CEN national Members. Ref. No. EN ISO 14663-1:2006: EEN ISO 14663-1:2006 (E) 2ForewordThe text of ISO 14663-1:1999 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 14663-1:2006 by Technical C

13、ommittee CEN/TC 249 “Plastics”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the

14、latest by October 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ir

15、eland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement noticeThe text of ISO 14663-1:1999 has been approved by CEN as EN ISO 14663-1:2006 without any modifications. 1 Scope1.1

16、This part of ISO 14663 establishes a system of designation for ethylene/vinyl alcohol (EVOH) copolymerthermoplastic materials, which may be used as the basis for specifications.1.2 The types of ethylene/vinyl alcohol (EVOH) copolymer plastic are differentiated from each other by aclassification syst

17、em based on appropriate levels of the designatory property:melt mass-flow rateand on information about basic polymer parameters, intended application and/or method of processing, importantproperties, additives, colorants, fillers and reinforcing materials.1.3 This part of ISO 14663 is applicable to

18、copolymers of ethylene and vinyl alcohol containing from 15 % (m/m) to60 % (m/m) of ethylene. It applies to materials ready for normal use in the form of powder, granules or pellets,unmodified or modified by colorants, additives, fillers, etc.1.4 It is not intended to imply that materials having the

19、 same designation give necessarily the same performance.This part of ISO 14663 does not provide engineering data, performance data or data on processing conditionswhich may be required to specify a material for a particular application and/or method of processing.If such additional properties are re

20、quired, they shall be determined in accordance with the test methods described inpart 2 of this International Standard, if suitable.1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing,additional requirements may be given in data block 5

21、(see clause 3, introductory paragraph).2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of this part ofISO 14663. At the time of publication, the editions indicated were valid. All standards are subject to revision, andpart

22、ies to agreements based on this part of ISO 14663 are encouraged to investigate the possibility of applying themost recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently validInternational Standards.ISO 1043-1:1997, Plastics Symbols and abbreviated

23、terms Part 1: Basic polymers and their specialcharacteristics.ISO 1133:1997, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) ofthermoplastics.ISO 14663-2:1999, Plastics Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials Part 2: Prepar

24、ation of test specimens and determination of properties.3 EN ISO 14663-1:2006 (E) 3 Designation systemThe designation system for thermoplastics is based on the following standardized pattern:DesignationIdentity blockDescription blockInternationalIndividual-item block(optional)StandardnumberblockData

25、block1Datablock2Datablock3Datablock4Datablock5The designation consists of an optional description block, reading “Thermoplastics”, and an identity blockcomprising the International Standard number and an individual-item block. For unambiguous designation, theindividual-item block is subdivided into

26、five data blocks comprising the following information: Data block 1: Identification of the plastic by its symbol EVOH in accordance with ISO 1043-1 and informationabout the polymerization process or composition of the polymer (see 3.1). Data block 2: Position 1: Intended application or method of pro

27、cessing (see 3.2).Positions 2 to 8: Important properties, additives and supplementary information (see 3.2). Data block 3: Designatory properties (see 3.3). Data block 4: Fillers or reinforcing materials and their nominal content (see 3.4). Data block 5: For the purpose of specifications, a fifth da

28、ta block may be added containing additional information.This kind of information is not relevant to this part of ISO 14663.The first character of the individual-item block shall be a hyphen. The five data blocks shall be separated from eachother by commas. If a data block is not used, this shall be

29、indicated by doubling the separation sign, i.e. by twocommas (,).3.1 Data block 1In this data block, after the hyphen, ethylene/vinyl alcohol copolymers are identified by the symbol EVOH, inaccordance with ISO 1043-1, and, after a space, a two-figure code-number giving the ethylene content of thecop

30、olymer as specified in table 1.EN ISO 14663-1:2006 (E) 4 Table 1 Code-numbers used for ethylene content in data block 1Code-number Range of ethylene content% (m/m)18 H11022 15 but H11088 2023 H11022 20 but H11088 2528 H11022 25 but H11088 3033 H11022 30 but H11088 3538 H11022 35 but H11088 4043 H110

31、22 40 but H11088 4548 H11022 45 but H11088 5053 H11022 50 but H11088 5558 H11022 55 but H11088 60The ethylene content shall be determined by the method specified in ISO 14663-2, annex B.3.2 Data block 2In this data block, information about intended application and/or method of processing is given in

32、 position 1 andinformation about important properties, additives and colour in positions 2 to 8. The code-letters used are specifiedin table 2.If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall beinserted in position 1.Table 2 Code-

33、letters used in data block 2Code-letter Position 1 Code-letter Positions 2 to 8A Adhesives A Processing stabilizedB Blow moulding B AntiblockingC ColouredD PowderE ExtrusionF Extrusion of films F Special burning characteristicsG General use G GranulesG1 PelletsH Coating H Heat-ageing stabilizedL Lig

34、ht or weather stabilizedM MouldingN Natural (no colour added)P Impact modifiedR Mould release agentS LubricatedT TransparentV Thermoforming V Heat shrinkableX No indication X CrosslinkableY Textile yarns, spinning Y Increased electrical conductivityZ AntistaticEN ISO 14663-1:2006 (E) 5 3.3 Data bloc

35、k 3In this data block, the melt mass-flow rate is represented by a single code-letter (indicating the conditions ofmeasurement) immediately followed by a three-figure code-number (indicating the range in which the value falls).If a value falls on or near a range limit, the manufacturer shall state w

36、hich range will designate the material. Ifsubsequent individual test values lie on, or on either side of, the limit because of manufacturing tolerances, thedesignation is not affected.The melt mass-flow rate shall be determined in accordance with ISO 1133, using set of conditions X1)(see table 3).Se

37、t of conditions D is intended for comparisons with PE, E/VAC or other polymers, provided the melting point of theethylene/vinyl alcohol copolymer is below 190 C.Table 3 Test conditions for determination of melt mass-flow rateCode-letter Test temperatureCNominal loadkgD 190 2,16X 210 2,16The possible

38、 values of the melt mass-flow rate are divided into 11 ranges, each represented by a three-figure code-number as specified in table 4.Table 4 Code-numbers used for melt mass-flow rate in data block 3Code-number Range of melt mass-flow rateg/10 min000001003006012022045090200400700H11022 0,10 but H110

39、22 0,20 but H11022 0,40 but H11022 0,80 but H11022 1,5 but H11022 3,0 but H11022 6,0 but H11022 12 but H11022 25 but H11022 50H11088 0,10H11088 0,20H11088 0,40H11088 0,80H11088 1,5H11088 3,0H11088 6,0H11088 12H11088 25H11088 501)This set of conditions is proposed for inclusion in the next edition of

40、 ISO 1133.EN ISO 14663-1:2006 (E) 6 3.4 Data block 4In this data block, the type of filler and/or reinforcing material is represented by a single code-letter in position 1 andits physical form by a second code-letter in position 2, the code-letters being as specified in table 5. Subsequently(without

41、 a space), the filler/reinforcing material content by mass may be given by a two-figure number in positions 3and 4.Table 5 Code-letters used for fillers and reinforcing materials in data block 4Code-letter Material Code-letter FormB Boron compound B Beads, spheres, ballsC Carbon1)C Chips, cuttingsD

42、PowderE ClayF FibreG Glass G GroundH WhiskersK Calcium carbonate K Knitted fabricL Cellulose1)L LayerM Mineral1) 2), metal 1)M Mat (thick)N Non-woven fabric (thin)P Mica1)P PaperQ Silcon compoundR Aramid R Mould release agentS Synthetic, organic1)S Scale, flakeT Talc T CordV VeneerW Wood1)W Woven fa

43、bricX Not specified X Not specifiedY YarnZ Others1)Z Others1)1) These materials may be further defined by their chemical symbol, for example, or additionalsymbols defined in the relevant International Standard. In the case of metals (M), it is essential toindicate the type of metal by means of its c

44、hemical symbol.2) Mixtures of materials and/or forms may be indicated by combining the relevant codes, using thesign “+” and placing the whole between parentheses. For example, a mixture of 25 % glass fibre (GF)and 10 % mineral powder (MD) would be indicated by (GF25+MD10).4 Examples of designations

45、An ethylene/vinyl alcohol copolymer (EVOH) with an ethylene content of 36 % (m/m) (38), intended for extrusion (E),without special additives and having a melt mass-flow rate (measured at 210 C using a 2,16 kg load) of14,7 g/10 min (X200), would be designated:EN ISO 14663-1:2006 (E) 7 Designation: Th

46、ermoplastics ISO 14663-EVOH38,EN,X200An ethylene/vinyl alcohol copolymer (EVOH) with an ethylene content of 21 % (m/m) (23), intended for moulding(M), coloured (C), in the form of pellets (G1), having a melt mass-flow rate (measured at 210 C using a 2,16 kgload) of 0,90 g/10 min (X012) and reinforced with 55 % of glass fibre (GF55), would be designated:Designation: Thermoplastics ISO 14663-EVOH23,MCG1,X012,GF55EN ISO 14663-1:2006 (E) 8