DIN EN 573-5-2007 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5 Codification of standardized wrought products English version of DIN E.pdf

《DIN EN 573-5-2007 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5 Codification of standardized wrought products English version of DIN E.pdf》由会员分享，可在线阅读，更多相关《DIN EN 573-5-2007 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5 Codification of standardized wrought products English version of DIN E.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、November 2007DEUTSCHE NORM English price group 10No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.150.10!$JF#“139350

2、0www.din.deDDIN EN 573-5Aluminium and aluminium alloys Chemical composition and form of wrought products Part 5: Codification of standardized wrought productsEnglish version of DIN EN 573-5:2007-11Aluminium und Aluminiumlegierungen Chemische Zusammensetzung und Form von Halbzeug Teil 5: Bezeichnung

3、von genormten KneterzeugnissenEnglische Fassung DIN EN 573-5:2007-11www.beuth.deDocument comprises 15 pagesDIN EN 573-5:2007-11 2 National foreword This standard has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, Working Group WG 7 “Sheets, strips and plates” (Secr

4、etariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards Committee), Steering Body of Section 1 Aluminium. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 573-5September 2007ICS 77.040.30; 77.120.10Engli

5、sh VersionAluminium and aluminium alloys - Chemical composition andform of wrought products - Part 5: Codification of standardizedwrought productsAluminium et alliages daluminium - Composition chimiqueet forme des produits corroys - Partie 5: Codification desproduits corroys normalissAluminium und A

6、luminiumlegierungen - ChemischeZusammensetzung und Form von Halbzeug - Teil 5:Bezeichnung von genormten KneterzeugnissenThis European Standard was approved by CEN on 13 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thi

7、s EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (En

8、glish, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

9、 Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONC

10、OMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 573-5:2007: EEN 573-5:2007 (E) 2 Contents Foreword3 Introduction .

11、4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Codification system.5 Figure 1 Structure of codification system .5 Table 1 Codification for dimension and form of extruded and drawn products .7 Table 2 Codification for dimension and form of rolled products7 Table 3 Other examples fo

12、r wrought forging stock8 Table 4 Other examples for wire and drawing stock8 Table 5 Other examples for extruded and drawn products .10 Table 6 Other examples for rolled products11 Bibliography 12 PageEN 573-5:2007 (E) 3 Foreword This document (EN 573-5:2007) has been prepared by Technical Committee

13、CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2008, and conflicting national standards shall be with

14、drawn at the latest by March 2008. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 “Sheet, strip and plate“ to prepare the following standard: EN 573-5, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 5: Codification of sta

15、ndardized wrought products. EN 573 comprises the following parts under the general title “Aluminium and aluminium alloys Chemical composition and form of wrought products“: Part 1: Numerical designation system Part 2: Chemical symbol based designation system Part 3: Chemical composition and form of

16、products Part 4: Forms of products Part 5: Codification of standardized wrought products Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 a

17、ffirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national

18、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan

19、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 573-5:2007 (E) 4 Introduction The significance of a standard codification lies in the rational, unambiguous description of products, above all in the field of design, scheduling of operations, material suppli

20、es and in the field of offering and ordering. The exchange of information between companies and plants made possible by product codification becomes more and more important for communication. The system proposed in the present document provides a standardized pattern from which a rapid and unequivoc

21、al description of a product is possible, instead of a lengthy verbal description. It can be used advantageously in cases where the reference to semi products should be short and consistent, such as drawings or part lists. It is not intended to replace the technical conditions of inspection and deliv

22、ery as laid down in the specific product standards. EN 573-5:2007 (E) 5 1 Scope This document specifies the codification of some standardized semifinished wrought products for use in ordering information. NOTE Codification is usually required for technical drawings. It does not apply to castings, ca

23、st forging stock, rolling ingots, extrusion billets and ingots for remelting. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refe

24、renced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 570, Aluminium and aluminium alloys Impact extrusion slugs obtained from wrought products Specification EN 573-3, Aluminium and aluminium alloys Chemical composition and

25、 form of wrought products Part 3: Chemical composition and form of products EN 1592-4, Aluminium and aluminium alloys - HF seam welded tubes - Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part

26、 1: General terms 3 Terms and definitions For the purposes of this document the terms and definitions given in EN 12258-1:1998 apply. 4 Codification system 4.1 General This system contains in abbreviated form important technical data required for a product order or tender. In the product standards,

27、where technical conditions for inspection and delivery are specified, there are included additional specifications needed for an order or tender. The requirements of these standards shall not be affected by this codification standard. Each codification consists of a “Description Block“ and an “Ident

28、ification Block“. The system is illustrated in Figure 1. Codification Identification Block Description Block European Standard Number Block Individual Item Block Figure 1 Structure of codification system EN 573-5:2007 (E) 6 4.2 Description Block Codification according to this document shall be restr

29、icted to the products specified in EN 573-3 and the relevant product standards. The definitions of these products are specified in EN 12258-1. The description shall be as short as possible and should be taken preferably from the title of the standard or the descriptors, the one which best characteri

30、zes the standardized product. The description shall be translated in the national versions of the European Standard since the product can be identified by the European Standard number block too. 4.3 Identification Block 4.3.1 Structure of Identification Block The Identification Block consists of two

31、 consecutive blocks of characters, the European Standard Number Block and the Individual Item Block. In order to mark the division between the two blocks, a hyphen () shall be the first character of the Individual Item Block. 4.3.2 European Standard Number Block If the European Standard of a product

32、 consists of several parts issued, the number of the relevant part where tolerances on dimensions and form are specified shall be taken. All the requirements concerning technical conditions of inspection and delivery, mechanical properties and additional properties laid down in the relevant parts of

33、 the standard shall be applicable. 4.3.3 Individual Item Block In order to allow an unambiguous coding of the standardized product the characteristics should be given in the following sequence where the first, second and third characteristic should be separated by a hyphen (): material designation;

34、temper designation; parameters, e.g. dimensions (thickness width length). Numerical values for parameters shall be used absolutely. In cases where no dimensions can be coded, e.g. drawing number for forgings or extruded profiles, letters in front of figures are allowed. Reference to drawings may be

35、coded with letters and figures, where letters should be explained by a short text outside of the codification. No symbols shall be used which could be mistaken for codification symbols. Entries in plain language as characteristics, e.g. for shape and type or design data, shall be coded to prevent th

36、eir translation into other languages. Some codifications are given in the examples and they should be standardized in the product standards when these are subject of revision. 4.3.4 Terms, designations and cods to be used in the Identification Block Material designation specified in EN 573-3 shall b

37、e used whenever possible. Temper designation specified in EN 515 shall be used whenever possible. For dimensions and form, the following designations, composed of a code and two or more numbers A, B, C , according to Table 1, shall be used. For sheet and plate the code “RCT“ shall not be used. All d

38、imensions shall be specified in millimetres, with the exception of foil and finstock thicknesses which are specified in micrometers. For products of irregular cross-sections which are not covered by Table 1, the reference code of the drawing shall be written instead of the designation. EN 573-5:2007

39、 (E) 7 For coiled products and products required in random lengths only the cross-sectional dimensions shall be codified. Further specifications, e.g. related to inside diameter of the coil, shall be given according to the relative standards. For circles only the thickness and the circle diameter sh

40、all be indicated as part of the codification. For slugs the codification system shall apply as specified in EN 570. Further designation characteristics shall be used only if agreed upon between supplier and purchaser, for round tubes and for sheet, strip and plate. For any other form of products, re

41、ference to drawings shall be used. Table 1 Codification for dimension and form of extruded and drawn products Product description Explanation Dimension symbols Explanation HEX-bar Bar, hexagonal cross-section A C Width across flats lengthaRCT-bar Bar, rectangular cross-section A B C Thickness width

42、lengthaSQU-bar Bar, square cross-section A C Width across flats lengthaRND-bar Bar, round cross-section A C Diameter lengthaRND-tube Tube, round cross-section OD B C Outside diameter wall thickness lengthaRND-tube Tube, round cross-section ID B C Inside diameter wall thickness lengthaRND-tube Tube,

43、round cross-section OD ID C Outside diameter inside diameter lengthaRL (instead of C) Length as fabricated (random length) NOTE For products of irregular cross-sections which are not covered by this table, the reference code of the drawing should be written instead of the designation, followed by a

44、figure describing the fixed length in millimetres or the designation “RL“ if random length is required. aIf a length is specified, this shall be considered as fixed length. Table 2 Codification for dimension and form of rolled products Product description Dimension symbols Explanation Strip, foil A

45、B Thickness width Sheet, plate A B C Thickness width length Circle, hot-rolled A B Thickness circle diameter Circle, cold-rolled A B Thickness circle diameter 4.4 Examples 4.4.1 General The codification will be explained in the examples either by a short text and/or schematically. When quoting the c

46、haracteristic features the same order shall be used for those appearing in the explanation as in the codification. Supplementary coded expressions shall be added in parentheses in the explanation after the corresponding data. The following examples are listed in sections according to the product gro

47、ups and one example is listed only. It is entrusted to the working groups of CEN/TC 132 to amend their product standards by the codification system when these standards are to be revised. EN 573-5:2007 (E) 8 4.4.2 Forgings and wrought forging stock EXAMPLE Forging conforming to EN 586-3, in material

48、 EN AW-6082, in temper T6, drawing number G3737. Forging EN 586-3 EN AW-6082 T6 G3737 Denomination Number of the European Standard Material designation Temper designation Drawing number Table 3 Other examples for wrought forging stock Denomination Number of the EN Material designation Temper designa

49、tion Nominal dimensions RCT-Bar EN 603-3 EN AW-6082 T62 80 120 1 500 Plate EN 603-3 EN AW-5083 H111 60 1 000 1 500 4.4.3 Wire and drawing stock EXAMPLE Rectangular (RCT) wire conforming to EN 1301-3, in material EN AW-5754, in temper H12, nominal thickness 5,0 mm, nominal width 6,0 mm, length as fabricated. RCT-Wire EN 1301-3 EN AW-5754 H12 5,0 6,0 RL Denomination Number of the European Standard Material designation Temper