DIN EN 13146-8-2012 Railway applications - Track - Test methods for fastening systems - Part 8 In service testing German version EN 13146-8 2012《轨道交通 轨道 紧固设备的试验方法 第8部分 使用测试》.pdf

《DIN EN 13146-8-2012 Railway applications - Track - Test methods for fastening systems - Part 8 In service testing German version EN 13146-8 2012《轨道交通 轨道 紧固设备的试验方法 第8部分 使用测试》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13146-8-2012 Railway applications - Track - Test methods for fastening systems - Part 8 In service testing German version EN 13146-8 2012《轨道交通 轨道 紧固设备的试验方法 第8部分 使用测试》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、June 2012 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 93

2、.100!$|y*“1898607www.din.deDDIN EN 13146-8Railway applications Track Test methods for fastening systems Part 8: In service testingEnglish translation of DIN EN 13146-8:2012-06Bahnanwendungen Oberbau Prfverfahren fr Schienenbefestigungssysteme Teil 8: BetriebserprobungEnglische bersetzung von DIN EN

3、13146-8:2012-06Applications ferroviaires Voie Mthodes dessai pour les systmes de fixation Partie 8: Essai en serviceTraduction anglaise de DIN EN 13146-8:2012-06SupersedesDIN EN 13146-8:2007-06www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document compr

4、ises 10 pages06.12 DIN EN 13146-8:2012-06 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 256 “Railway applications” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss F

5、ahrweg und Schienen-fahrzeuge (Railway Standards Committee), Working Committee NA 087-00-01-04 UA Schienenbefestigungs-systeme. Amendments This standard differs from DIN EN 13146-8:2007-06 as follows: a) in the foreword of the EN the standards series EN 13146, Railway applications Track Test methods

6、 for fastening systems, has been completed; b) requirements of EN 13146-9 regarding static and dynamic stiffness have been taken into account; c) requirements related to the test and test report have been revised; d) the standard has been editorially revised. Previous editions DIN EN 13146-8: 2002-1

7、1, 2007-06 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13146-8 April 2012 ICS 93.100 Supersedes EN 13146-8:2002English Version Railway applications - Track - Test methods for fastening systems - Part 8: In service testing Applications ferroviaires - Voie - Mthodes dessai pour les systmes de

8、 fixation - Partie 8: Essai en service Bahnanwendungen - Oberbau - Prfverfahren fr Schienenbefestigungssysteme - Teil 8: BetriebserprobungThis European Standard was approved by CEN on 26 November 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the cond

9、itions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exist

10、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national stan

11、dards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

12、key and United Kingdom. Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13146-8:2012: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMI

13、TEE FR NORMUNG EN 13146-8:2012 (E) 2 Contents Page Foreword 31 Scope. 52 Normative references 5 3 Terms and definitions 54 Principle 55 Test conditions . 56 Procedure . 66.1 Duration of test . 66.2 Maintenance . 66.3 Inspection . 67 Test report 7Bibliography 8DIN EN 13146-8:2012-06 EN 13146-8:2012 (

14、E) 3 Foreword This document (EN 13146-8:2012) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

15、 the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

16、 or all such patent rights. This document supersedes EN 13146-8:2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. No major changes have been made in this revision of EN 13146-8:2002. This European Standard is one of

17、 the series EN 13146 “Railway applications Track Test methods for fastening systems“ which consists of the following parts: Part 1: Determination of longitudinal rail restraint; Part 2: Determination of torsional resistance; Part 3: Determination of attenuation of impact loads; Part 4: Effect of rep

18、eated loading; Part 5: Determination of electrical resistance; Part 6: Effect of severe environmental conditions; Part 7: Determination of clamping force; Part 8: In service testing; Part 9: Determination of stiffness. These support the requirements in the series EN 13481 “Railway applications Track

19、 Performance requirements for fastening systems“. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,

20、France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13146-8:2012-06 EN 13146-8:2012 (E) 4 Introduction As fastening syste

21、ms are safety critical, there is a need to have a standardized procedure to evaluate their performance in normal use. Performance in track is not always completely predicted from the laboratory tests in EN 13146, Parts 1 to 7 and 9. The test described in this part of EN 13146 is intended to provide

22、a procedure which can be used to compare the performance in track of new or modified fastening systems with systems whose performance is known. In accordance with EN 13481-2:2012, EN 13481-3:2012, EN 13481-4:2012, EN 13481-5:2012 and EN 13481-7:2012, this test has to be performed when required by th

23、e user. DIN EN 13146-8:2012-06 EN 13146-8:2012 (E) 5 1 Scope This European Standard specifies a procedure for the comparative testing of fastening systems in track. The test procedure is applicable to fastening systems which in all other respects conform to EN 13481-2:2012, EN 13481-3:2012, EN 13481

24、-4:2012, EN 13481-5:2012 and EN 13481-7:2012. This test applies to complete fastening assemblies. It is only used for comparative testing of such fastening systems installed at the same time on the type of support for which they are intended. 2 Normative references The following documents, in whole

25、or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13146-9:2009, Railway applications Tra

26、ck Test methods for fastening systems Part 9: Determination of stiffness EN 13481-1:2012, Railway applications Track Performance requirements for fastening systems Part 1: Definitions 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13481-1:2012 apply.

27、 4 Principle The fastening system under test is installed in track at the same time as a reference fastening system, on sleepers, bearers or slab track of the same material and design. Location in track is arranged so that the test and reference fastening systems are in track with similar geometry a

28、nd service conditions. 5 Test conditions The performance of a fastening system, systems or variants of a system under test shall be compared with a reference fastening system. Test and reference fastening systems shall be installed in one track in lengths containing not less than 500 sleepers each o

29、r 200 sleepers each on metro systems or their equivalent for slab track. Installation shall be within a period not exceeding 7 days. All fastening systems in any test shall be installed on the type of sleeper for which they are designed and only one type of sleeper shall be used in a test. Each fast

30、ening system in a test shall be installed in track with similar conditions of formation, ballast support, curvature, gradient and cant, and with similar traffic conditions including traffic volume, type, speed, braking and acceleration. If installation has involved a change in sleepers the track sha

31、ll be consolidated mechanically, or by the passage of 1 105t (gross) traffic, prior to commencement of the test. The following shall be recorded. method of installing sleepers, bearers or slab; method of installing fastening components; method of installing rail; DIN EN 13146-8:2012-06 EN 13146-8:20

32、12 (E) 6 weather conditions during installation. Rail used in the test shall be the same grade and section for the whole test length. The head shall be free of defects and consistent throughout the test lengths, and the foot shall be smooth on its underside. Any welded or bolted joints shall be susp

33、ended or supported in accordance with the normal practice of the user. During the test all mechanical joints shall be properly maintained. All track maintenance of the test lengths shall be done concurrently. 6 Procedure 6.1 Duration of test The minimum test period shall be that necessary for the fo

34、llowing traffic to pass over the test track and shall be not less than 1 year. For category A and B fastening systems 10 106t (gross) For category C, D and E fastening systems 20 106t (gross) NOTE Categories of fastening systems are defined in EN 13481-1:2012. 6.2 Maintenance During the test each fa

35、stening system shall be maintained in accordance with the manufacturers instructions. 6.3 Inspection Prior to the commencement of measurements, behaviour of the fastening system shall be visually observed and recorded during installation and consolidation of the track. At the commencement, at any sp

36、ecified intermediate stage and at the end of the test the following shall be measured or observed for all systems being tested, including the reference system: a) track gauge; b) longitudinal movement of rail, relative to the sleeper or slab support, and maximum daily temperature range; c) effect on

37、 performance of signalling systems; d) clamping force, on not less than 10 assemblies, using the manufacturers recommended test method for use in track; e) rail pad static stiffness on not less than 10 pads, if required by the purchaser, measured in accordance with EN 13146-9:2009; f) details of ins

38、tallation methods and weather during installation; g) security of attachment to the sleepers; h) condition of the rail head; i) condition of sleepers including rail seat area; DIN EN 13146-8:2012-06 EN 13146-8:2012 (E) 7 j) condition of individual fastening components; k) ease of assembly and remova

39、l using the tools recommended by the manufacturer. For items (d), (i), (j) and (k) not less than 2 % of the assemblies shall be selected at random for examination. The assemblies selected shall be the same each time the measurement or observation is repeated. 7 Test report The test report shall incl

40、ude at least the following information: a) railway organization involved, location and dates of test; b) description of the fastening system including manufacturers designation; c) description and manufacturers designation of reference fastening system; d) details of the track used for the test, inc

41、luding sleeper type, rail type, formation, ballast type and depth, gradient, curvature and cant; e) rail pad static stiffness on not less than 10 pads, if required by the purchaser; f) details of installation methods and weather during installation; g) duration of test, type and quantity and speed o

42、f traffic; h) results of inspection and testing described in 6.3; i) an assessment of the performance of the fastening system under test relative to the reference fastening system; j) maintenance record of the track and the fastening assembly during test period. DIN EN 13146-8:2012-06 EN 13146-8:201

43、2 (E) 8 Bibliography 1 EN 13481-2:2012, Railway applications Track Performance requirements for fastening systems Part 2: Fastening systems for concrete sleepers 2 EN 13481-3:2012, Railway applications Track Performance requirements for fastening systems Part 3: Fastening systems for wood sleepers 3

44、 EN 13481-4:2012, Railway applications Track Performance requirements for fastening systems Part 4: Fastening systems for steel sleepers 4 EN 13481-5:2012, Railway applications Track Performance requirements for fastening systems Part 5: Fastening systems for slab track with rail on the surface or rail embedded in a channel 5 EN 13481-7:2012, Railway applications Track Performance requirements for fastening systems Part 7: Special fastening systems for switches and crossings and check rails DIN EN 13146-8:2012-06