BS ISO 14737-2015 Carbon and low alloy cast steels for general applications《一般应用碳素和低合金铸钢》.pdf

《BS ISO 14737-2015 Carbon and low alloy cast steels for general applications《一般应用碳素和低合金铸钢》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 14737-2015 Carbon and low alloy cast steels for general applications《一般应用碳素和低合金铸钢》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 14737:2015Carbon and low alloy caststeels for general applicationsBS ISO 14737:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 14737:2015.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/111, S

2、teel Castings and Forgings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015

3、.Published by BSI Standards Limited 2015ISBN 978 0 580 76504 9ICS 77.140.80Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2015.Amendments/corrigenda i

4、ssued since publicationDate T e x t a f f e c t e dBS ISO 14737:2015 ISO 2015Carbon and low alloy cast steels for general applicationsAciers mouls au carbone et faiblement allis dusage gnralINTERNATIONAL STANDARDISO14737Second edition2015-12-15Reference numberISO 14737:2015(E)BS ISO 14737:2015ISO 14

5、737:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,

6、 or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fa

7、x +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 14737:2015ISO 14737:2015(E)Foreword iv1 Scope . 12 Normative references 13 General conditions for delivery 14 Chemical composition . 15 Heat treatment . 16 Mechanical properties 17 Test methods . 18 Supplementary requirements 29 Marking 2Annex A (i

8、nformative) Guidance data for welding . 7Annex B (informative) UNS cast grades similar to ISO cast grades . 8Bibliography 9 ISO 2015 All rights reserved iiiContents PageBS ISO 14737:2015ISO 14737:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nat

9、ional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna

10、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intend

11、ed for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.i

12、so.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document wi

13、ll be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expres

14、sions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is The committee responsible for this document is

15、ISO/TC 17, Steel, Subcommittee SC 11, Steel castings.This second edition cancels and replaces the first edition (ISO 14737:2003) and ISO 3755, of which it constitutes a technical revision. Notably, the following changes have been made to the previous edition: carbon has replaced non-alloy in the tit

16、le of the standard; grades G21Mn5 and G50CrMo4 have been deleted; Annexes A and B have been replaced; new values and grade numbers have been added to Tables 1 and 2 and Annex A.iv ISO 2015 All rights reservedBS ISO 14737:2015INTERNATIONAL STANDARD ISO 14737:2015(E)Carbon and low alloy cast steels fo

17、r general applications1 ScopeThis International Standard specifies requirements for carbon and low alloy cast steel grades for general applications.NOTE Annex B gives information on ISO grade designation and available UNS numbers which are similar to the ISO grade designation.2 Normative referencesT

18、he following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 148-1

19、, Metallic materials Charpy pendulum impact test Part 1: Test methodISO 4990, Steel castings General technical delivery requirementsISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature3 General conditions for deliverySteel castings supplied in accordance with thi

20、s International Standard shall conform to the applicable requirements of ISO 4990, including the supplementary requirements that are indicated in the inquiry and purchase order.4 Chemical compositionThe chemical composition shall conform to the values given in Table 1.5 Heat treatmentThe type of hea

21、t treatment is left to the discretion of the manufacturer unless otherwise agreed upon at the time of inquiry and order. The information for heat treatment described in Table 2 is for information only.6 Mechanical propertiesMechanical properties are given in Table 2 and shall be subject to an agreem

22、ent at the time of inquiry and order.Unless otherwise specified (see ISO 4990), the thickness of the test block shall be 28 mm minimum.Properties at thicknesses greater than the maximum thickness in Table 2 may be lower and are subject to an agreement between manufacturer and purchaser.7 Test method

23、s7.1 The tensile test shall be performed in accordance with ISO 6892-1. ISO 2015 All rights reserved 1BS ISO 14737:2015ISO 14737:2015(E)7.2 The impact test shall be performed in accordance with ISO 148-1.8 Supplementary requirementsA list of supplementary requirements which may be used at the option

24、 of the purchaser is given in ISO 4990.9 MarkingMarking shall be as specified in ISO 4990.2 ISO 2015 All rights reservedBS ISO 14737:2015ISO 14737:2015(E)Table1 Chemical composition, % (m/m)GradedesignationCSiMnPSCrMoNiVCuNameNumberGE 2001.04200,0350,0300,300,120,400,030,30GS 2001.04490,180,601,200,

25、0300,0250,300,120,400,030,30GE2401.04460,0350,0300,300,120,400,030,30GS2401.04550,230,601,200,0300,0250,300,120,400,030,30GS2701.04540,240,601,300,0300,0250,30a0,12a0,40a0,03a0,30aGS 3401.04670,300,601,500,0300,0250,30a0,12a0,40a0,03a0,30aG28Mn61.11650,25 to 0,320,601,20 to 1,800,0350,0300,300,150,4

26、00,050,30G28MnMo61.54330,25 to 0,320,601,20 to 1,600,0250,0250,300,20 to 0,400,400,050,30G20Mo51.54190,15 to 0,230,600,50 to 1,000,0250,020b0,300,40 to 0,600,400,050,30G10MnMoV631.54100,12max.0,601,20 to 1,800,0250,0200,300,20 to 0,400,400,05 to 0,100,30G20NiCrMo221.67410,18 to 0,230,600,60 to 1,000

27、,0350,0300,40 to 0,600,15 to 0,250,40 to 0,700,050,30G25NiCrMo221.67440,23 to 0,280,600,60 to 1,000,0350,0300,40 to 0,600,15 to 0,250,40 to 0,700,050,30G30NiCrMo221.67780,28 to 0,330,600,60 to 1,000,0350,0300,40 to 0,600,15 to 0,250,40 to 0,700,050,30G17CrMo551.73570,15 to 0,200,600,50 to 1,000,0250

28、,020b1,00 to 1,500,45 to 0,650,400,050,30G17CrMo9101.73790,13 to 0,200,600,50 to 0,900,0250,020b2,00to2,500,90 to 1,200,400,050,30G26CrMo41.72210,22 to 0,290,600,50 to 0,800,0250,020b0,80 to 1,200,15 to 0,300,400,050,30G34CrMo41.72300,30 to 0,370,600,50 to 0,800,0250,020b0,80 to 1,200,15 to 0,300,40

29、0,050,30G42CrMo41.72310,38 to 0,450,600,60 to 1,000,0250,020b0,80 to 1,200,15 to 0,300,400,050,30G30CrMoV641.77250,27 to 0,340,600,60 to 1,000,0250,020b1,30 to 1,700,30 to 0,500,400,05 to 0,150,30G35CrNiMo661.65790,32 to 0,380,600,60 to 1,000,0250,020b1,40to1,700,15 to 0,351,40to1,700,050,30G30NiCrM

30、o731.65720,28 to 0,330,600,60 to 0,900,0350,0300,70 to 0,900,20 to 0,301,65 to 2,000,050,30G40NiCrMo731.65730,38 to 0,430,600,60 to 0,900,0350,0300,70 to 0,900,20 to 0,301,65 to 2,000,050,30G32NiCrMo85-41.65700,28 to 0,350,600,60 to 1,000,0200,0151,00to1,400,30 to 0,501,60 to 2,100,050,30Singlevalue

31、sindicatemaximums.aCr+Mo+Ni+V+Cu max. 1,00%.bFor castings of ruling thickness680bG26CrMo4 1.7221 150 to 300 G34CrMo4 1.7230 G42CrMo4 1.7231 200 to 350G30CrMoV64 1.7725 bG35CrNiMo66 1.6579 400 G30NiCrMo73 1.6572 200 to 350 G40NiCrMo73 1.6573 G32NiCrMo85-4 1.6570 200 to 350 aThe preheating temperature

32、 is related to the geometry, the thickness of the casting and climatic conditions.bThe post weld heat treatment temperature shall be at least 20 C, but not more than 50 C below tempering temperature. ISO 2015 All rights reserved 7BS ISO 14737:2015ISO 14737:2015(E)Annex B (informative) UNS cast grade

33、s similar1)to ISO cast gradesTable B.1 UNS grades similar1)to ISO cast gradesGrade designation UNS number (similar grade)Name NumberGE200 1.0420 J03000GS200 1.0449 J02001GE240 1.0446 J03000GS240 1.0455 J02003GS270 1.0454 J02503GS 340 1.0467 J03003G28Mn6 1.1165 G28MnMo6 1.5433 G20Mo5 1.5419 G10MnMoV6

34、3 1.5410 G20NiCrMo22 1.6741 J12047, J12095G25NiCrMo22 1.6744 J12595G30NiCrMo22 1.6778 J13095G17CrMo55 1.7357 G17CrMo910 1.7379 G26CrMo4 1.7221 J13502G34CrMo4 1.7230 J14047, J23259G42CrMo4 1.7231 G30CrMoV64 1.7725 G35CrNiMo66 1.6579 G30NiCrMo73 1.6572 J23259G40NiCrMo73 1.6573 J24053G32NiCrMo85-4 1.65

35、70 NOTE The grade designations including the names and the numbers follow the rules of EN 10027-1 and EN 10027-2.1) The similar UNS (Unified Numbering System) grades may not be equivalent to the grades in this International Standard.8 ISO 2015 All rights reservedBS ISO 14737:2015ISO 14737:2015(E)Bib

36、liography1 ISO 3755, Cast carbon steels for general engineering purposes2 EN 10027-1, Designation system for steels Part 1: Steel names3 EN 10027-2, Designation system for steels Part 2: Steel numbers ISO 2015 All rights reserved 9BS ISO 14737:2015ISO 14737:2015(E) ISO 2015 All rights reservedICS 77

37、.140.80Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are publish

38、ed by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The

39、knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge

40、 that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international

41、 standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make

42、 using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always

43、be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automat

44、ically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can

45、 cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality

46、 of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the p

47、roperty of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patent

48、s Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSI