BS EN 61204-1995 Low-voltage power supply devices d c output - Performance characteristics and safety requirements《直流输出的低压供电装置 性能特征和安全性要求》.pdf

《BS EN 61204-1995 Low-voltage power supply devices d c output - Performance characteristics and safety requirements《直流输出的低压供电装置 性能特征和安全性要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61204-1995 Low-voltage power supply devices d c output - Performance characteristics and safety requirements《直流输出的低压供电装置 性能特征和安全性要求》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61204:1995 Incorporating Amendment No. 1 Low-voltage power supply devices, d.c. output Performance characteristics The European Standard EN 61204:1995 with the incorporation of A1:2001 has the status of a British Standard ICS 29.160.40 29.200 NO COPYING WITHOUT BSI PERMISSION

2、EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 61204:1995 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 August 1995 BSI 28 June 2002 The following BSI references re

3、late to the work on this standard: Committee reference PEL/22 Draft for comment 85/20768 DC ISBN 0 580 24283 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PEL/22, Static power convertor equipment, upon which the follo

4、wing bodies were represented: Association of Consulting Engineers Electricity Association Engineering Equipment and Materials Users Association GAMBICA (BEAMA Ltd.) Institution of Electrical Engineers Institution of Incorporated Executive Engineers Power Supply Manufacturers Association PSMA (BEAMA

5、Ltd.) Railway Industry Association Transmission and Distribution Association (BEAMA Ltd.) The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Energy Industries Council Federation of the Electronics Industry Amendments issued since publication

6、 Amd. No. Date Comments 13278 28 June 2002 Indicated by a sideline and see national forewordBS EN 61204:1995 BSI 28 June 2002 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 61204 4 National annex NA (informative) Original IEC text amended by CENE

7、LEC common modifications 27BS EN 61204:1995 ii BSI 28 June 2002 National foreword This British Standard has been prepared by Technical Committee PEL/22 and is the English language version of EN 61204:1995 Low-voltage power supply devices, d.c. output Performance characteristics and safety requiremen

8、ts, including amendment A1:2001, published by the European Committee for Electrotechnical Standardization (CENELEC). It was derived by CENELEC from IEC 61204:1993, Edition 1.1:2001, which comprises Edition 1:1993 consolidated by the incorporation of amendment 1:2001. The CENELEC common modifications

9、 have been implemented at the appropriate places in the text and are indicated by a side line in the margin. Parts of the original IEC text that have been modified by CENELEC have been quoted in National Annex NA. The foreword of the EN makes reference to the “date of withdrawal”, dow, of the releva

10、nt national standard. In this case the relevant national standard is BS 6688:1986 which will be withdrawn on 1995-12-01. Certificates and marks will not be awarded after this date with respect to the withdrawn British Standard. However such certificates and marks, already awarded, may continue to ap

11、ply to production until 2000-12-01. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find”

12、 facility of the BSI Standards Electronic Catalogue. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a Publicly Available Specification does not of itself confer immunity from legal obligation

13、s. Summary of pages This document comprises a front cover, an inside front cover, pages i to ii, the EN title page, pages 2 to 27 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent c

14、hanges by amendment.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61204 January 1995 + A1 May 2001 ICS 29.160.40 Descriptors: Electrical power supply, low voltage, performance evaluation, safety, overvoltage protection, overcurrent protection, tests English version Low-voltage power supply de

15、vices, d.c. output Performance characteristics (includes amendment A1:2001) (IEC 61204:1993, modified + A1:2001) Dispositifs dalimentation basse tension, sortie en courant continu Caractristiques de fonctionnement (inclut lamendement A1:2001) (CEI 61204:1993 + A1:2001, modifie) Stromversorgungsgerte

16、 fr Niederspannung mit Gleichstromausgang Eigenschaften (enthlt nderung A1:2001) (IEC 61204:1993 + A1:2001, modifiziert) This European Standard was approved by CENELEC on1994-12-06. Amendment A1:2001 was approved by CENELEC on 2001-03-01. CENELEC members are bound to comply with the CEN/CENELEC Inte

17、rnal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC m

18、ember. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENE

19、LEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization

20、Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC members Ref No. EN 61204:1995 + A1:2001 EEN 61204:1995 BSI 28 June 2002 2 Foreword The text of the Internationa

21、l Standard IEC 1204:1993, prepared by SC 22E, Stabilized power supplies, of IEC TC 22, Power electronics, together with common modifications prepared by CENELEC BTTF 64-2, was submitted to the formal vote and was approved by CENELEC as EN 61204 on 1994-12-06. The following dates were fixed: For prod

22、ucts which have complied with the relevant national standard before 1995-12-01, as shown by the manufacturer or by a certification body, this previous standard may continue to apply for production until 2000-12-01. Annexes designated “normative” are part of the body of the standard. In this standard

23、, Annex A, Annex B, Annex C, Annex D and Annex ZA are normative. Annex ZA has been added by CENELEC. Foreword to amendment A1 The text of document 22E/77/FDIS, future amendment 1 to IEC 61204:1993, prepared by SC 22E, Stabilized power supplies, of IEC TC 22, Power electronics, was submitted to the I

24、EC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 61204:1995 on 2001-03-01. The following dates were fixed: Contents Page Foreword 2 Introduction 4 1G e n e r a l 5 1.1 Scope and object 5 1.2 Normative references 5 1.3 Definitions 6 2 Presentation of performance characterist

25、ics 7 3 Performance 7 3.1 Rated outputs and total output power 7 3.2 Ambient operating temperature range 9 3.3 Ambient storage and transit temperature range 10 3.4 Source voltage and frequency 10 3.5 Source current 10 3.6 Source effect (source regulation) 11 3.7 Load effect (load regulation) 12 3.8

26、Output voltage tolerance (intrinsic error) fixed outputs 12 3.9 Adjustability of output voltage 12 3.10 Periodic and random deviation 13 3.11 Interaction effects (cross regulation) 13 3.12 Temperature coefficient 14 3.13 Hold-up time (turn-off decay time) 14 3.14 Start-up time (turn-on delay time) 1

27、4 3.15 Turn-on (turn-off) overshoot 14 3.16 Transient response to load current changes 15 3.17 Output overvoltage protection 16 3.18 Output overcurrent protection 16 3.19 Mean time between failures (MTBF) 17 4 Requirements for protective devices 17 4.1 Thermal protection 17 4.2 Input overcurrent pro

28、tection 17 5 Acoustic noise requirements 17 6 Additional requirements 18 6.1 Remote programming (remote control) 18 6.2 Remote sensing 18 6.3 Mechanical characteristics 18 6.4 Series operation 18 6.5 Parallel operation 18 6.6 Monitoring and control signals 19 latest date by which the EN has to be im

29、plemented at national level by publication of an identical national standard or by endorsement (dop) 1995-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1995-12-01 latest date by which the amendment has to be implemented at national level by publ

30、ication of an identical national standard or by endorsement (dop) 2001-12-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2004-03-01EN 61204:1995 BSI 28 June 2002 3 Page 7 Test requirements 19 7.1 General 19 7.2 Environmental tests 19 8 Miscel

31、laneous requirements 19 8.1 Markings and instructions 19 Annex A (normative) Periodic and random deviation test methods 20 Annex B (normative) Output overvoltage protection 23 Annex C (normative) Overcurrent protection characteristics 24 Annex D (normative) Parallel operation 25 Annex ZA (normative)

32、 Other international publications quoted in this standard with the references of the relevant European publications 26 Figure 1 Resistive load applied at the output terminals 15 Figure 2 Resistive load removed at the output terminals 15 Figure A.1 Differential test probe 21 Figure A.2 Differential t

33、est arrangement 21 Figure A.3 Current probe test arrangement 22 Figure C.1 Overcurrent protection characteristics 24 Table 1 Performance characteristics presentation 8 Table 2 Preferred transient response 166021 4 EI:C9911A+32:100 9 INTRODUCTION This International Standard, based on the British Stan

34、dard BS6688: 1986, has been reworked and extended to take into account existing and forthcoming IEC standards. With regard to safety, there was close collaboration with IEC technical committee 74, working group 6: Safety requirements for power supplies. Page4 EN61204:1995 6021 4 EI:C9911A+32:100 11

35、LOW-VOLTAGE POWER SUPPLY DEVICES, DC OUTPUT PERFORMANCE CHARACTERISTICS 1 General 1.1 Scope and object This international Standard describes a method for specifying requirements for low-voltage power supply devices (including switching types) providing d.c. output(s) up to 200 V d.c. at a power leve

36、l of up to 30 kW, operating from a.c. or d.c. source voltages of up to 600 V. The devices are for use within class I equipment or for free-standing operation when used with adequate electrical and mechanical protection. This standard is intended to be used for all types of a.c. or d.c. driver power

37、supplies with any number of outputs, specially produced for an unknown final application. In the case where power supplies are developed as a component of equipment covered by specific product standards, these standards apply; the additional application of IEC 61204 may be useful as an option, espec

38、ially if the performance characteristics are not sufficiently covered by the product standard. It permits to specify a power unit to meet a particular application by the specification of parameters at required performance levels, to establish the essential definitions related to this type of equipme

39、nt, and to establish a selection of levels of performance. These levels are carefully graded to enable manufacturers and users to select and specify a range of power supply devices suitable for their application. 1.2 Normative references The following normative documents contain provisions which, th

40、rough reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibi

41、lity of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently International Standards. IEC 60038:1983, IEC standard voltages IEC 60068: Environmental testing IEC 60068-2-1:1990, Environmental testing Part 2: Tests Tests A

42、: Cold IEC 60068-2-2:1974, Environmental testing Part 2: Tests Tests B: Dry heat IEC 60068-2-3:1969, Environmental testing Part 2: Tests Test Ca: Damp heat, steady state IEC 60068-2-6:1982, Environmental testing Part 2: Tests Test Fc and guidance: Vibration (sinusoidal) Page5 EN61204:1995 6021 4 EI:

43、C9911A+32:100 31 IEC 60068-2-27:1987, Environmental testing Part 2: Tests Test Ea and Guidance: Shock IEC 60068-2-29:1987, Environmental testing Part 2: Tests Test Eb and Guidance: Bump IEC 60478: Stabilized power supplies, d.c. output IEC 60478-1:1974, Stabilized power supplies, d.c. output Part 1:

44、 Terms and definitions IEC 60478-2:1986, Stabilized power supplies, d.c. output Part 2: Rating and performance IEC 60478-3:1989, Stabilized power supplies, d.c. output Part 3: Reference levels and measurement of conducted electromagnetic interference (EMI) IEC 60478-4:1976, Stabilized power supplies

45、, d.c. output Part 4: Tests other than radio- frequency interference IEC 60478-5:1993, Stabilized power supplies, d.c. output Part 5: Measurement of the magnetic component of the reactive near field IEC 60651:1979, Sound level meters IEC 60664-1:1992, Insulation co-ordination for equipment within lo

46、w-voltage systems Part 1: Principles, requirements and tests IEC 60721: Classification of environmental conditions IEC 60721-3-1:1987, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities. Storage IEC 60721-3-2:1985, Classificat

47、ion of environmental conditions Part 3: Classification of groups of environmental parameters and their severities. Transport IEC 60801: Electromagnetic compatibility for industrial-process measurement and control equipment IEC 60801-4:1988, Electromagnetic compatibility for industrial-process measur

48、ement and control equipment Part 4: Electrical fast transient/burst requirements IEC 60950:1991, Safety of information technology equipment, including electrical business equipment MIL-HDBK-217E:1974, Reliability prediction of electronic equipment 1.3 Definitions For the purpose of this Internationa

49、l Standard the definitions given in IEC 60950 and IEC 60478-1 apply, except where redefined in this standard. Page6 EN61204:1995 6021 4 EI:C9911A+32:100 51 2 Presentation of performance characteristics The performance characteristics are detailed in 3.1 to 8.1 and are in accordance with the performance criteria listed in table III of IEC 60478-2. The performance figure defines the maximum change (not typical) in the measured quantity which may be either posit