BS EN 60875-1-1-1998 Fibre optic branching devices - Blank detail specification《光纤分流装置 空白详细规格》.pdf

《BS EN 60875-1-1-1998 Fibre optic branching devices - Blank detail specification《光纤分流装置 空白详细规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60875-1-1-1998 Fibre optic branching devices - Blank detail specification《光纤分流装置 空白详细规格》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60875-1-1:1998 IEC 60875-1-1:1996 QC 810001: 1996 Fibre optic branching devices Part 1-1: Blank detail specification The European Standard EN 60875-1-1:1998 has the status of a British Standard ICS 33.180.20BSEN60875-1-1:1998 This British Standard, having been prepared under t

2、he directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15July1998 BSI 04-1999 ISBN 0 580 30109 5 National foreword This British Standard is the English language version of EN60875-1-1:1998. It is identical with IEC60875-1-1:1

3、996. The UK participation in its preparation was entrusted by Technical Committee EPL/86, Fibre optics, to Subcommittee EPL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European c

4、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From

5、 1 January 1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references At

6、tention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this docume

7、nt may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of Bri

8、tish Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 10 and a back cover.

9、 This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN60875-1-1:1998 BSI 04-1999 i Contents Page National foreword Inside fr

10、ont cover Foreword 2 Text of EN 60875-1-1 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60875-1-1 April 1998 ICS 33.180.20 Descriptors: Optical fibres, branching devices, specification English version Fibre optic branching devices Part1-1: Blank detail specification (IEC 60875-1-1:19

11、96) Dispositifs de couplage pour fibres optiques Partie 1-1: Spcification particulire cadre (CEI 60875-1-1:1996) Lichtwellenleiter-Verzweiger Teil1-1: Vordruck fr Bauartspezifikation (IEC60875-1-1:1996) This European Standard was approved by CENELEC on 1998-04-01. CENELEC members are bound to comply

12、 with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secre

13、tariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as t

14、he official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Commi

15、ttee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC memb

16、ers. Ref. No. EN 60875-1-1:1998 EEN60875-1-1:1998 BSI 04-1999 2 Foreword The text of the International Standard IEC60875-1-1:1996, prepared by SC86B, Fibre optic interconnecting devices and passive components, of IEC TC86, Fibre optics, was submitted to the formal vote and was approved by CENELEC as

17、 EN60875-1-1 on1998-04-01 without any modification. The following dates were fixed: Endorsement notice The text of the International Standard IEC60875-1-1:1996 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope 3 2 Qualification approval 3 3 Qua

18、lity conformance inspection 3 4 Detail specification worksheet 3 Table 1 Fixed sample test schedule for qualification approval 7 Table 2 Lot-by-lot quality conformance inspectionschedule 8 Table 3 Periodic quality conformance inspectionschedule 9 Table 4 Details, measurements and performancerequirem

19、ents 10 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-12-01EN60875-1-1:1998 BSI 04-1999 3 1 Sc

20、ope This blank detail specification is part of the generic specification IEC875-1 (QC810000) and comprises a blank worksheet with instructions for preparing detail specifications. 2 Qualification approval The test schedules for qualification by the fixed sample procedure are defined in Table 1. 3 Qu

21、ality conformance inspection 3.1 Lot-by-lot inspection The test schedules for lot-by-lot inspection (groups A and B) are defined in Table2. 3.2 Periodic inspection The test schedules for periodic inspection (groups C and D) are defined in Table3. 4 Detail specification worksheet The worksheet follow

22、ing is intended to aid in the preparation of detail specifications. Spaces are provided for entering the information. When the spaces are completed, the detail specification can be drafted in its final form. The spaces are identified by numbers between brackets. Instructions for completing these num

23、bered spaces are given below. When drafting the final detail specification, eliminate the bracketed instruction numbers. 1 The IEC number assigned to the detail specification is added by the National Committee. 2 The date of the detail specification is added by the National Committee. 3 Enter the na

24、me and address of the National Committee. 4 Enter the component classification. 5 Enter the page numbers where the variants are defined. 6 Enter the climatic category, if applicable. 7 Enter the assessment level(s). If the assessment level is other than a standard level, it is designated by the capi

25、tal letter “X”. 8 Add the qualification procedure required for the detail specification (fixed sample or lot-by-lot procedure). 9 Add figures showing the limit dimensions for standard reference components and gauges if they are required. Display the figures in the format shown. 10 Tabulate the ident

26、ification number for each variant. Assign a column in the table for each variant feature (for example, fibre size, cable jacket diameter, alternative mounting schemes, etc.). 11 Enter supplementary information with respect to marking, requirements for certified records of released lots, and other ap

27、propriate information. 12 Table 1 defines the required measurements and tests for qualification by fixed sample size. Specify the sample size for each group in column “n”. When a test or measurement is defined which is not given in IEC1300, but appears in another IEC publication, indicate the refere

28、nce by a note in the table. When a test or a measurement is defined which is not given in an IEC publication, clearly describe the procedure in an individual annex to the detail specification. Use an identical format to that used in IEC1300. Reference the procedure by a note in the table. After comp

29、leting the group “0” tests, the sample is divided to form the other sample groups. When needed, instructions for dividing the sample are given as a note in the table. 13 Table 2 defines the required measurements and tests for groups A and B. When a test or measurement is defined which is not given i

30、n IEC1300, but appears in another IEC publication, indicate the reference by a note in the table. When a test or a measurement is defined which is not given in an IEC publication, clearly describe the procedure in an individual annex to the detail specification. Use an identical format to that used

31、in IEC1300. Reference the procedure by a note in the table. Enter the assessment level(s). If the assessment level is other than a standard level, it is designated by the capital letter “X”. 14 Table 3 defines the required measurements and tests for groups C and D periodic tests. Specify the sample

32、size for each group in column “n”. When a test or measurement is defined which is not given in IEC1300, but appears in another IEC publication, indicate the reference by a note in the table. When a test or a measurement is defined which is not given in an IEC publication, clearly describe the proced

33、ure in an individual annex to the detail specification. Use an identical format to that used in IEC1300. Reference the procedure by a note in the table.EN60875-1-1:1998 4 BSI 04-1999 After completing the group “C0” or “D0” tests, the sample is divided to form the other sample groups. When needed, in

34、structions for dividing the sample are given as a note in the table. Enter the assessment level(s). If the assessment level is other than a standard level, it is designated by the capital letter “X”. 15 When completed, Table 4 will contain the details, measurements and performance requirements for a

35、ll tests and measurements which appear in Table1, Table2 and Table3. The format for measurements appears on lines16,17 and18. Enter the measurement procedure title and reference location on line16. Enter the measurement detail on lines17. The requirements for independent measurements (measurements w

36、hich are not part of an environmental test) shall either be specified as a note in the table where it was added (Table1, Table2 or Table3), or included in Table4 under the appropriate measurement on line18. The requirements for dependent measurements (measurements which are part of an environmental

37、test) shall be specified under the environmental test Table4. The format for environmental tests appears on lines19,20,21,22 and23. Enter the test procedure title and reference location on line19. Enter the test details on line20. Enter the initial measurements to be made along with the performance

38、requirements on line21. Enter the measurements to be made during the test, together with the performance requirements on line22. Enter the final measurements to be made together with the performance requirements on line23.EN60875-1-1:1998 BSI 04-1999 5 9 Drawing DIMENSIONS REF. NOTES MIN. MAX. NOTES

39、 1 . 2 , etc. Figure EN60875-1-1:1998 6 BSI 04-1999 10 VARIANT IDENTIFICATION NUMBERS NUMBER: QC XXXXX-YYYY yyyy Variant feature Variant feature Variant feature 11 SUPPLEMENTARY INFORMATION Component marking: (When specified, add component marking requirements here. See2.6.2 of IEC875-1). Component

40、package marking: (When specified, add component package marking requirements here. See2.6.3 of IEC875-1). Certified records of released lots: (Indicate whether a certified records of released lots is required. See3.5 of IEC875-1).EN60875-1-1:1998 BSI 04-1999 7 (12) Table 1 Fixed sample test schedule

41、 for qualification approval Test sequence IEC 1300 n Group 0 Group 1 Group 2 . . . . NOTES 1n = sample size. 2The test details, measurements, and performance requirements are given in Table4.EN60875-1-1:1998 8 BSI 04-1999 13 Table 2 Lot-by-lot quality conformance inspection schedule Groups A and B A

42、ssessment level Test sequence IEC 1300 clause number A B C X IL AQL IL AQL IL AQL IL AQL Group A Group B NOTES 1The test details, measurements and performance requirements are given in Table4. 2IL = inspection level; AQL = acceptable quality level.EN60875-1-1:1998 BSI 04-1999 9 14 Table 3 Periodic q

43、uality conformance inspection schedule Groups C and D Assessment level Test sequence IEC 1300 clause number A B C X n p n p n p n p Group C0 Group C1 Group C2 Group D0 Group D1 Group D2 NOTES 1The test details, measurements, and performance requirements are given in Table 4. 2n = sample size; p = pe

44、riodicity in months.EN60875-1-1:1998 10 BSI 04-1999 15 Table 4 Details, measurements and performance requirementsblankBS EN 60875-1-1:1998 IEC 60875-1-1:1996 QC 810001: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for p

45、reparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editio

46、ns. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the insid

47、e front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addres

48、sed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of in

49、formation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchas