BS EN 60384-24-1-2006 Fixed capacitors for use in electronic equipment - Blank detail specification - Surface mount fixed tantalum electrolytic capacitors with conductive polymer s.pdf

《BS EN 60384-24-1-2006 Fixed capacitors for use in electronic equipment - Blank detail specification - Surface mount fixed tantalum electrolytic capacitors with conductive polymer s.pdf》由会员分享，可在线阅读，更多相关《BS EN 60384-24-1-2006 Fixed capacitors for use in electronic equipment - Blank detail specification - Surface mount fixed tantalum electrolytic capacitors with conductive polymer s.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58 Part 24-1: Blank detail specification Surface mount fixed tantalum electrolytic capacitors with co

2、nductive polymer solid electrolyte Assessment level EZThe European Standard EN 60384-24-1:2006 has the status of a British StandardICS 31.060.40; 31.060.50Fixed capacitors for use in electronic equipment BRITISH STANDARDBS EN 60384-24-1: 2006BS EN 60384-24-1:2006This British Standard was published u

3、nder the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49202 8Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal o

4、bligations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 60384-24-1:2006. It is identical with IEC 60384-24-1:2006.The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment.

5、 A list of organizations represented on EPL/40X can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARD EN 60384-24-1 NORME EUROPENNE EUROPISCHE NORM August 2006 CENELEC European Committee for Electrotechnical Stand

6、ardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-24-1

7、:2006 E ICS 31.060.40; 31.060.50 English version Fixed capacitors for use in electronic equipment Part 24-1: Blank detail specification Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ (IEC 60384-24-1:2006) Condensateurs fixes utiliss

8、 dans les quipements lectroniques Partie 24-1: Spcification particulire cadre Condensateurs fixes lectrolytiques au tantale pour montage en surface lectrolyte solide en polymre conducteur Niveau dassurance de la qualit EZ (CEI 60384-24-1:2006) Festkondensatoren zur Verwendung in Gerten der Elektroni

9、k Teil 24-1: Vordruck fr Bauartspezifikation Oberflchenmontierbare Tantal-Elektrolyt-Kondensatoren mit leitfhigem Polymerfestkrper-Elektrolyten Bewertungsstufe EZ (IEC 60384-24-1:2006) This European Standard was approved by CENELEC on 2006-07-01. CENELEC members are bound to comply with the CEN/CENE

10、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any C

11、ENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versio

12、ns. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia,

13、Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 40/1732/FDIS, future edition 1 of IEC 60384-24-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 6038

14、4-24-1 on 2006-07-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow)

15、 2009-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-24-1:2006 was approved by CENELEC as a European Standard without any modification. _ EN 60384-24-1:2006 2 3 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 24-1: Blank detail s

16、pecification Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimu

17、m content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications the content of 1.4 of the sectional specification shall be

18、taken into account. The numbers between square brackets on the first page of the detail specification correspond to the following information, which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission” or the Nation

19、al Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specificati

20、on. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when applicable). 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to t

21、he national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Application or group of applications covered and/or assessment level. 9 Reference data on the most important properties, to allow comparison between the various ca

22、pacitor types. EN 60384-24-1:20061 2 IEC 60384-24-1 4 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH : 3 Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte 5 6 Outline drawing : (see Table 1) (angle projection) 7 Assessment level(s): EZ 8 Inf

23、ormation on the availability of components qualified to this detail specification is given in IEC QC 001005. (9) 1 General data 1.1 Recommended method(s) of mounting (to be inserted) (See 1.4.2 of IEC 60384-24). 1.2 Dimensions Table 1 Case size reference and dimensions Dimension mm Case size referen

24、ce L W H NOTE 1 When there is no case size reference, Table 1 may be omitted and the dimensions should be given in Table 2, which then becomes Table 1. NOTE 2 The dimensions should be given as maximum dimensions or as nominal dimensions with a tolerance. EN 60384-24-1:2006 4 1.3 Ratings and characte

25、ristics Rated capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (see Table 2) Climatic category Rated temperature Variation of capacitance with temperature (see Table 3) Tangent of loss angle (see Table 3) Leakage current (see Table 3) Equiva

26、lent series resistance (see Table 3) Surge voltage (see Table 2) Table 2 Values of capacitance and of voltage related to case sizes Rated voltage V Category voltage V Rated tempera-ture Surge voltage V Upper category tempera-ture Case sizes Case sizes Case sizes Case sizes Rated capacitance F Table

27、3 Characteristics Maximum values Capacitance change % Tangent of loss angle tan at 120 Hz Leakage current A Equivalent series resistance at 100 kHzm Case size URV CRF -55 C Rated tem-pera-ture Upper cate-gory tem-pera-ture -55 C 20 C Rated tem-pera-ture Uppercate-gorytem-pera-ture 20 C Rated tem-per

28、a-ture Upper cate-gory tem-pera-ture 20 C EN 60384-24-1:2006 5 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

29、nt (including any amendments) applies. IEC 60384-1:1999, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-24:2006, Fixed capacitors for use in electronic equipment Part 24: Sectional specification Surface mount fixed tantalum electrolytic capacitors with condu

30、ctive polymer solid electrolyte 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of 1.6 of IEC 60384-24. NOTE The details of the marking of the component and package should be given in full in the detail specification. 1.6 Ordering information Ord

31、ers for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) rated capacitance; b) tolerance on rated capacitance; c) rated d.c. voltage; d) number and issue reference of the detail specification and style reference; e) packaging in

32、structions. 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE Additions or increased requirements should b

33、e specified only when essential. Table 4 Other characteristics This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. 2 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval, the procedures sha

34、ll be in accordance with 3.4 of IEC 60384-24. 2.1.2 For quality conformance inspection, the test schedule (Table 5) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of IEC 60384-24. EN 60384-24-1:2006 6 Table 5 Test schedule for qualit

35、y conformance inspection Number of specimens and number of non-conforming itemsbSubclause number and testa D or NDbConditions of testa IL n c Performance requirementsa Group A inspection (lot-by-lot) Subgroup A0 4.18 High surge current (if applicable) ND 100 %c 4.5.1 Leakage current Protective resis

36、tor: 1 000 As in Table 3 4.5.2 Capacitance Frequency: 120 Hz Within specified tolerance 4.5.3 Tangent of loss angle (tan ) Frequency: 120 Hz As in Table 3 4.5.4 Equivalent series resistance (ESR) (if applicable) Frequency: 100 kHz As in Table 3 Subgroup A1 4.4 Visual examination ND S-3 d0 As in 4.4.

37、2 Legible marking (if required) and as specified in the detail specification Subgroup A2 4.4 Dimension (detail)eND S-3 d0 As specified in Table 1 of this specification Group B inspection (lot-by-lot) S-3 d0 4.7 Solderability D 4.7.1 Test See detail specification for the method 4.7.2 Final measuremen

38、t Visual examination As in 4.7.2 EN 60384-24-1:2006 7 Table 5 Test schedule for quality conformance inspection (continued) Number of specimens and number of non-conforming itemsbSubclause number and testa D or NDbConditions of testa p n c Performance requirementsa Group C inspection (Periodic) Subgr

39、oup C1 D 3 12 0 4.6 Resistance to soldering heat f4.6.1 Initial measurement Capacitance For use as reference value 4.6.2 Test Method: Deflection: s Reflow profile: Recovery: 24 h 2 h 4.6.3 Final measurement Visual examination Leakage current Capacitance Tangent of loss angle (tan ) Equivalent series

40、 resistance (ESR) As in 4.6.3 As in Table 3 See detail specification As in Table 3 See detail specification Sub group C2 D 3 12 0 4.9 Substrate bending test f4.9.1 Initial measurement Capacitance For use as reference value 4.9.3 Final inspection Capacitance (with printed board in bent position) See

41、detail specification Sub group C3 4.3 Mounting Substrate material: 4.3.1 Initial measurement Capacitance (the value obtained in 4.5.2 may be used) 4.3.3 Final inspection D Visual examination Leakage current Capacitance Tangent of loss angle (tan ) Equivalent series resistance (ESR) gNo visible damag

42、e As in Table 3 C/C 8 % As in Table 3 See detail specification EN 60384-24-1:2006 8 Table 5 Test schedule for quality conformance inspection (continued) Number of specimens and number of non-conforming itemsbSubclause number and testa D or NDbConditions of testa p n c Performance requirementsa Sub g

43、roup C3.1 6 18 0 4.8 Shear test Visual examination fNo visible damage 4.10 Rapid change of temperature 4.10.1 Initial measurement Capacitance (the value obtained in Group 3 may be used) 4.10.2 Test TA= Lower category temperature TB= Upper category temperature Five cycles Duration t1 = 30 min Recover

44、y: 1 h to 2 h Leakage current Capacitance As in Table 3 C/C 10 % of value measured in 4.10.1 4.10.3 Final measurements Tangent of loss angle (tan ) As in Table 3 4.11 Climatic sequence 4.11.1 Initial measurement Capacitance (the value obtained in 4.10.3 may be used) 4.11.2 Dry heat Temperature: uppe

45、r category temperature Duration: 16 h 4.11.3 Damp heat, cyclic, test Db, first cycle 4.11.4 Cold Temperature: lower category temperature Duration: 2h 4.11.5 Damp heat, cyclic, test Db, remaining cycles Visual examination Leakage current Capacitance No visible damage Legible marking As in Table 3 C/C

46、 20 % of the value measured in 4.11.1 4.11.6 Final measurements Tangent of loss angle 1,2 times the limit of Table 3 EN 60384-24-1:2006 9 Table 5 Test schedule for quality conformance inspection (continued) Number of specimens and number of non-conforming itemsbSubclause number and testa D or NDbCon

47、ditions of testa p n c Performance requirementsa Subgroup C3.2 D 6 12 0 4.12 Damp heat, steady stateRecovery: 1 h to 2 hf4.12.1 Initial measurementCapacitance (the value obtained in Group 3 may be used)Visual examination Leakage current Capacitance No visible damage Legible marking 5 x initial limit

48、 -20 % C/C 40 % of the value measured in 4.12.1 4.12.3 Final measurements Tangent of loss angle 1,2 times the limit of Table 3 Sub group C3.3 D 6 15 0 4.13 Characteristics at high and low temperature The capacitors shall be measured at each temperature step fStep 1:20 C Leakage current Capacitance Tangent of loss angle As in Table 3 For use as reference value As in Table 3 Step 2: lower category temperature Capacitance (if applicable) Tangent of loss angle (if applicable) As in Table 3 As in Table 3 Step 3 :20 C Leakage current Capacitance Tangent of loss angle As in Table 3 C/C 5 % of v