BS EN 12849-2009 Bitumen and bituminous binders - Determination of penetration power of bituminous emulsions《沥青和沥青粘合剂 沥青乳化液穿透力的测定》.pdf

《BS EN 12849-2009 Bitumen and bituminous binders - Determination of penetration power of bituminous emulsions《沥青和沥青粘合剂 沥青乳化液穿透力的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12849-2009 Bitumen and bituminous binders - Determination of penetration power of bituminous emulsions《沥青和沥青粘合剂 沥青乳化液穿透力的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12849:2009ICS 75.140; 91.100.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDBitumen andbituminous binders Determination ofpenetration power ofbituminous emulsionsBS 2000-487:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Un

2、controlled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2009 BSI 2009ISBN 978 0 580 64097 1Amendments/corrigenda issued since publicationDate CommentsBS EN 12849:2009National forewordThis British Standard is the UK impleme

3、ntation of EN 12849:2009. Itsupersedes BS EN 12849:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PTI/13, Petroleum testing and terminology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publi

4、cation does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Energy Institute, under the brand of IP, publishes and sells all Parts of BS 2000, and all B

5、S EN petroleum test methods that would be Part of BS 2000, both in its annual publication “Standard methods for analysis and testing of petroleum and related products and British Standard 2000 Parts” and individually.Further information is available from: Energy Institute, 61 New Cavendish Street, L

6、ondon W1G 7AR. Tel: 020 7467 7100. Fax: 020 7255 1472.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 12849March 2009ICS 75.140; 91.100.50 Supersedes EN 12849:2002 English VersionBitu

7、men and bituminous binders - Determination of penetrationpower of bituminous emulsionsBitumes et liants bitumineux - Dtermination du pouvoir depercolation des mulsions de bitumeBitumen und bitumenhaltige Bindemittel - Bestimmung derEindringfhigkeit von BitumenemulsionenThis European Standard was app

8、roved by CEN on 17 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationa

9、lstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notifi

10、ed to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

11、Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation

12、in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12849:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms

13、and definitions .4 4 Principle 4 5 Reagents and materials 4 6 Apparatus .5 7 Sampling .6 8 Procedure .6 9 Expression of results 6 10 Precision .7 11 Test report 7 Annex A (normative) Characteristics of the Silica Sand Type F 34 8 Annex B (normative) Characteristics of the Testing Silica Filler 315-0

14、01 .9 Bibliography . 10 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 3 Foreword This document (EN 12849:2009) has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”, the secretariat of which is

15、held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attention is drawn to the poss

16、ibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12849:2002. From the previous edition, new reference filler is now specified; a mixture

17、of silica sand and silica filler is used as reference filler. Characteristics of both silica sand and silica filler are given respectively in normative Annex A and Annex B. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to

18、 implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switze

19、rland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 4 1 Scope This European Standard specifies a method for the determination of the penetration power of bituminous emulsions, through refer

20、ence filler. This test method is applicable to low-viscosity bituminous emulsions. WARNING The use of this standard can involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the

21、 user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition

22、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 58, Bitumen and bituminous binders - Sampling bituminous binders EN 12594, Bitumen and bituminous binders - Preparation of test samples 3 Terms and definitions For the purpose

23、s of this document, the following terms and definitions apply. 3.1 penetration power ability of a bitumen emulsion to penetrate into a reference filler 3.2 penetration time time, in minutes, required for a specified quantity of bituminous emulsion to penetrate into a defined quantity of a reference

24、filler 4 Principle A specified quantity of the emulsion to be tested is poured onto the reference filler. The time required for the emulsion to penetrate into the filler is measured. 5 Reagents and materials A mixture of specified silica sand and silica filler is used as the reference filler. In the

25、 event of a dispute, the reference filler specified shall be used. 5.1 Sand The silica sand type F 341shall be used as one of the two components of the reference filler. Characteristics are given in Annex A. 1The silica sand type F 34 is the trade name of a product supplied by Quarzwerke GmbH. This

26、information is given for the convenience of users of this European Standard and does not constitute an endorsement by CEN of the product name. Equivalent products may be used if they can be shown to lead to the same results, or if a correlation between the products has been established. Licensed Cop

27、y: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 5 5.2 Filler The testing silica filler 315-0012)shall be used as one of the two components of the reference filler. Characteristics are given in Annex B. 6 Apparatus Usual laborat

28、ory apparatus and glassware, together with the following: 6.1 Test apparatus, as shown in Figure 1, consisting of a glass tube with fused-on glass filter disc with pore size between 160 m and 250 m. A vent, below the glass filter disc, provides pressure compensation when the test apparatus is charge

29、d. The vent shall be cut perpendicular to the vertical axis, with its edges slightly fused. NOTE The vent can be dispensed with if, during the test procedure, the test apparatus is supported. Dimensions in millimetres Key 1. Glass filter disc 2. Vent Figure 1 Test apparatus 2) The testing silica fil

30、ler 315-001 is the trade name of a product supplied by Quarzwerke GmbH. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by CEN of the product name. Equivalent products may be used if they can be shown to lead to the same results

31、, or if a correlation between the products has been established. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 6 6.2 Balance, capable of weighing 100 g, with an accuracy of 0,1 g. 6.3 Oven, capable of being mainta

32、ined at (110 5) C. 6.4 Wooden board, 200 mm x 200 mm x 10 mm in size. 6.5 Stopwatch, graduated in divisions of 1 s or less. 7 Sampling The material under test shall be sampled in accordance with EN 58 and prepared in accordance with EN 12594. The test shall be carried out on two test portions of the

33、 sample, each weighing (10,0 0,1) g (see Clause 8). 8 Procedure 8.1 General Carry out the procedure under normal laboratory conditions, between 18 C and 28 C. 8.2 Test Dry the quantities of silica sand and testing silica filler, required for the test, in the oven (6.3) at a temperature of (110 5) C

34、until constant mass is reached and cool to ambient temperature in a desiccator. For each test portion, mix intimately (50,0 0,1) g of silica sand and (50,0 0,1) g of testing silica filler and transfer via a funnel to the upper part of the test apparatus (6.1), lifting the funnel with increasing fill

35、ing height. Level the surface of the filler mixture in the apparatus by knocking the lower edge of the test apparatus three times on the wooden board (6.4). Place the apparatus on the balance (6.2). Pour (10,0 0,1) g of the emulsion to be tested along a glass rod onto the centre of the filler mixtur

36、e. Pour the entire quantity of emulsion within (10 1) s. Start measuring the time immediately after pouring the emulsion. Cover the test apparatus using a watch glass. Determine the time for the emulsion to completely penetrate into the filler mixture, i.e. when the structure of the filler at its up

37、per surface can be clearly recognised. If penetration of the filler mixture is not completed within 20 min, discontinue the test. Repeat the test procedure using new quantities of filler and emulsion. If the results for both sample portions differ by more than 3 min, repeat the procedure for a third

38、 sample portion. The two values nearest to each other are used to calculate the mean penetration time. 9 Expression of results Express the individual penetration times and the average penetration time, in minutes, to the nearest integer. Express the result as the arithmetic mean of the two individua

39、l results of penetration time, to the nearest integer. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 7 10 Precision NOTE The precision of the method was evaluated in accordance with EN ISO 4259 2. 10.1 Repeatabili

40、ty The difference between two successive test results, obtained by the same operator with the same apparatus under constant operating conditions on identical test material would, in the long run, in the normal and correct operation of the test method, exceed 3 min in only one case in twenty. 10.2 Re

41、producibility The difference between two single and independent results obtained by different operators working in different laboratories on identical test material would, in the long run, in the normal and correct operation of the test method, exceed 6 min in only one case in twenty (provided that

42、both results have been determined within two weeks). NOTE The source of precision data is DIN 52046 1. 11 Test report The test report shall contain at least the following information: a) type and complete identification of the sample under test; b) reference to this European Standard; c) reference t

43、o the type of apparatus used; d) reference to the used sand and filler; e) result of the test (see Clause 9); f) any deviation, by agreement or otherwise, from the procedure specified; g) date of sampling, date of sample preparation and date of the test. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA S

44、TANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 8 Annex A (normative) Characteristics of the Silica Sand Type F 34 The Silica Sand Type F 34 shall have at least the following properties: Natural fine silica, uncrushed; SiO2content greater than 99 %; Density of

45、 (2 650 20) kg/m3; Particle size distribution, as % passing: 0,355 mm from 0 % to 4 %; 0,25 to 0,355 mm from 2 % to 22 %; 0,18 to 0,25 mm from 32 % to 67 %; 0,125 to 0,18 mm from 19 % to 51 %; 315 m 0,1%; 250 m 2 %; 200 m 9 %; 160 m 25 %; 125 m 54 %; 100 m 69 %; 80 m 74 %; 63 m 78 %; 50 m 82 %; 40 m

46、 84 %. The Testing Silica Filler Type 315-001 is available from Quarzwerke GmbH, Kaskadenweg 40, D-50226 Frechen, Tel.: +49-(0)2234-101-0, Fax: +49-(0)2234-101-400, e-mail: , . Key X Particle size, mm Y residue, % Figure B.1 Typical gradation of Testing Silica Filler 315-001 Licensed Copy: Wang Bin,

47、 ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009EN 12849:2009 (E) 10 Bibliography 1 DIN 52046, Testing of bituminous binders Determination of the wettability of bonding emulsion 2 EN ISO 4259, Petroleum products - Determination and application of precision

48、data in relation to methods of test (ISO 4259:2006) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy, (c) BSIBS EN 12849:2009This page has been intentionally left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 04/08/2009 02:41, Uncontrolled Copy

49、, (c) BSIEnergy InstituteBuying Parts of BS 2000Orders for BS 2000 publications should be addressed to either:Energy Institute Library and Information Service61 New Cavendish StreetLondonW1G 7ARTel: +44 (0)20 7467 7100Fax: +44 (0)20 7255 1472www.energyinst.org.ukOrder standards securely via:www.energyinstpubs.org.ukor:British Standards Institution Customer Services389 Chiswick High RoadLondonW4 4ALTel: +44 (0)20 8996 9001Fax: +44 (0)20 8996 7001www.bsi