BS EN 4604-003-2009 Aerospace series - Cable electrical for signal transmission - Cable coaxial 50 ohm 200 C type WZ - Product standard《航空航天系列 信号传输用电缆 WZ型、200℃、50 0hms同轴电缆 产品标准》.pdf

《BS EN 4604-003-2009 Aerospace series - Cable electrical for signal transmission - Cable coaxial 50 ohm 200 C type WZ - Product standard《航空航天系列 信号传输用电缆 WZ型、200℃、50 0hms同轴电缆 产品标准》.pdf》由会员分享，可在线阅读，更多相关《BS EN 4604-003-2009 Aerospace series - Cable electrical for signal transmission - Cable coaxial 50 ohm 200 C type WZ - Product standard《航空航天系列 信号传输用电缆 WZ型、200℃、50 0hms同轴电缆 产品标准》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN4604-003:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Cable, electrical, forsignal transmissionPart 003: Cable, coaxial, 50 ohm, 200 C,type WZ Product standardThis British Standardwas published under theauthority of the Sta

2、ndardsPolicy and StrategyCommittee on 31 March2009 BSI 2009ISBN 978 0 580 62394 3Amendments/corrigenda issued since publicationDate CommentsBS EN 4604-003:2009National forewordThis British Standard is the UK implementation of EN 4604-003:2009.The UK participation in its preparation was entrusted to

3、TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its corr

4、ect application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 4604-003:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4604-003 February 2009 ICS 49.060 English Version Aerospace series - Cable, electrical, for signal transmission - Part 003: Cable, c

5、oaxial, 50 ohm, 200 C, type WZ - Product standard Srie arospatiale - Cbles lectriques pour transmission de signaux - Partie 003: Cble coaxial, 50 ohm, 200 C, type WZ - Norme de produit Luft- und Raumfahrt - Elektrisch Leitungen fr Signalbertragungen - Teil 003: Koaxialkabel, 50 Ohm, 200 C, Typ WZ -

6、Produktnorm This European Standard was approved by CEN on 21 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp

7、hical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

8、CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

9、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B

10、-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4604-003:2009: EBS EN 4604-003:2009EN 4604-003:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Required characteris

11、tics .45 Quality assurance 96 Designation . 107 Identification and marking . 108 Packaging, labelling and delivery length . 109 Technical specification 10BS EN 4604-003:2009EN 4604-003:2009 (E) 3 Foreword This document (EN 4604-003:2009) has been prepared by the Aerospace and Defence Industries Asso

12、ciation of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. Thi

13、s European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by August 2009. Attention is drawn to the possibility that some of the

14、 elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement th

15、is European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the

16、 United Kingdom. BS EN 4604-003:2009EN 4604-003:2009 (E) 4 1 Scope This standard specifies the characteristics of a UV laser printable coaxial cable, 50 , type WZ, for use in aircraft electrical systems at operating temperatures between 65 C and 200 C and especially for high frequency up to 3 GHz. 2

17、 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3475-100*, Aerospace ser

18、ies Cables, electrical, aircraft use Test methods Part 100: General EN 3838, Aerospace series Requirements and tests on user-applied markings on aircraft electrical cables 1)EN 4604-001, Aerospace series Cable, electrical, for signal transmission Part 001: Technical specification EN 4604-002, Aerosp

19、ace series Cable, electrical, for signal transmission Part 002: General TR 6058, Aerospace series Cable code identification list 2)ASTM B 298-99, Standard specification for silver-coated soft or annealed copper wire 3)3 Terms and definitions For the purposes of this document, the terms and definitio

20、ns given in EN 3475-100:2002 apply. 4 Required characteristics 4.1 Material, construction, dimensions and mass 4.1.1 Material See Table 1. Table 1 Material Material Finish Colour Conductor Single strand copper per ASTM B298-99 1 m silver plated Without colouration Dielectric Fluoropolymer Without co

21、louration Screen (foil) Metallized Foil Without colouration Shield Braid, copper per ASTM B298-99 1 m silver plated Without colouration Jacket Fluorinated Ethylene Propylene (FEP) White * And all parts quoted in Table 4. 1) Published as ASD Prestandard at the date of publication of this standard. 2)

22、 Published as ASD Technical Report at the date of publication of this standard. 3) Published by: American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103, USA. BS EN 4604-003:2009EN 4604-003:2009 (E) 5 4.1.2 Construction, dimensions and mass See Figure 1 and Table

23、2. EN WZ DEG00Conductor Dielectric Screen (foil) Shield JacketKey 1 Conductor 2 Dielectric 3 Screen (foil) 4 Shield 5 Jacket Figure 1 Construction Table 2 Dimensions and mass Diameter Mass mm g/m Conductor Dielectric Shield Cable min. max. min. max. min. max. min. nom. max. nom. max. 0,88 0,93 2,20

24、2,50 2,90 3,20 3,40 3,60 3,70 26 30 4.2 General characteristics Operating temperature: 65 C to 200 C Minimum bend radius: in static use: 37 mm in dynamic use: 100 mm Performances are guaranteed up to 3 GHz. 1 2 3 4 5 BS EN 4604-003:2009EN 4604-003:2009 (E) 6 4.3 Electrical characteristics Characteri

25、stic impedance: Zc = (50 2) . Maximum power handling (at sea level): see Table 3 and Figure 2. Attenuation versus frequency: see Table 3 and Figure 2. Capacitance per unit length: 88 pF/m max. Velocity of propagation: 0,75 c nom. Transfer impedance from 1 MHz to 3 000 MHz: 30 m/m max. Table 3 Freque

26、ncy, attenuation and power handling Frequency MHz 50 200 400 1 000 3 000 Attenuation dB/100 m a 11 19 28 47 90 Power handling cw W a1 100 660 450 250 150 aMaximum attenuation and power handling values of a WZ cable. Figure 2 Maximum attenuation curve (ascending) Power curve (descending) 110100100010

27、0001 10 100 1000 10000f(MHz)Att.(dB/100m)P(W)Att.(dB/100m)P(W)BS EN 4604-003:2009EN 4604-003:2009 (E) 7 4.4 Tests See Table 4. Table 4 Tests EN 3475- Designation of the test Remarks 201 Visual examination Applicable 202 Mass Applicable 203 Dimensions Applicable 301 Ohmic resistance per unit length A

28、pplicable 28 /km max. 302 Voltage proof test Applicable Dielectric: Dry test: 4 000 VAC Jacket: Dry test: 2 000 VAC or Dry impulse test: 5 000 V Immersion test: 1 000 VAC 303 Insulation resistance Applicable 1 000 M.km min. at 20 C between conductor and shield 304 Surface resistance Applicable 1 250

29、 M.mm min. at 20 C 305 Overload resistance Not applicable 306 Continuity of conductors Applicable 307 Corona extinction voltage Applicable Extinction voltage = 1 900 VAC 401 Accelerated ageing Not applicable 402 Shrinkage and delamination Not applicable 403 Delamination and blocking Not applicable 4

30、04 Thermal shock Not applicable 405 Bending at ambient temperature Not applicable 406 Cold bend test Applicable Load = 7 N Temperature ( 65 2) C Mandrel diameter 50 mm 407 Flammability Applicable Load = 10 N 408 Fire resistance Not applicable 409 Air-excluded ageing Not applicable continued BS EN 46

31、04-003:2009EN 4604-003:2009 (E) 8 Table 4 Tests (continued) EN 3475- Designation of the test Remarks 410 Thermal endurance Not applicable 411 Resistance to fluids Applicable 412 Humidity resistance Not applicable 413 Wrap back test Not applicable 414 Differential scanning calorimeter (DSC test) Not

32、applicable 415 Rapid change of temperature Applicable Variation of capacitance: 5 % max. Increase of attenuation: 5 % max. Shrinkage: 2 mm max. 1stSpecimen length (C,): 10 m 416 Thermal stability Applicable Heat exposure temperature: 200 C Variation of capacitance: 5 % max. Increase of attenuation:

33、5 % max. Variation of impedance: 3 % max. Shrinkage: 2 mm max. 3rdSpecimen length (C,): 10 m 418 Thermal endurance for conductors Not applicable 501 Dynamic cut-through Not applicable 502 Notch propagation Applicable Notch = 0,05 mm Mandrel diameter = 50 mm 503 Scrape abrasion Applicable F = 10 N 50

34、4 Torsion Not applicable 505 Tensile test on conductors and strands Applicable, breaking load 150 N min. Elongation 25 % min. 506 Plating continuity Applicable 507 Adherence of plating Applicable 508 Plating thickness Applicable, thickness 1 m min. 509 Solderability Not applicable 510 Tensile streng

35、th and elongation of extruded insulation, sheath and jacket material Not applicable 511 Cable-to-cable abrasion Not applicable 512 Flexure endurance Not applicable 513 Deformation resistance (Installation with plastic cable ties) Applicable Application force: 70 N 5 % 514 Porosity of copper cladding

36、 on aluminium strands Not applicable 601 Smoke density Applicable, Dm = 200 max. within 4 minutes continued BS EN 4604-003:2009EN 4604-003:2009 (E) 9 Table 4 Tests (concluded) EN 3475- Designation of the test Remarks 602 Toxicity Applicable 603 Resistance to wet arc tracking Not applicable 604 Resis

37、tance to dry arc propagation Not applicable 605 Wet short circuit test Not applicable 701 Strippability and adherence of insulation to the conductor Applicable Adherence force 3 N min. 702 Screen pushback capability Applicable 703 Permanence of manufacturers marking Applicable 704 Flexibility Not ap

38、plicable 705 Contrast measurement Applicable K 50 % EN 3838 Requirements and tests on user-applied markings on aircraft electrical cables 706 Laser markability Applicable 801 Capacitance per unit length Capacitance Cp = 88 pF/m max. 802 Capacitance unbalance Not applicable 803 Capacitance variation

39、Not applicable 804 Velocity of propagation Applicable v: 225 000 km/s 805 Characteristic impedance Applicable Zc = (50 2) at 200 MHz 806 Attenuation Applicable (dB/m) A at 50 MHz A at 200 MHz A at 400 MHz A at 1 000 MHz A at 3 000 MHz 807 Transfer impedance Applicable ZT = 30 m/m max. from 1 MHz to

40、3 000 MHz 808 Cross-talk Not applicable 809 Resistance unbalance Not applicable 810 Structural return loss Not applicable 5 Quality assurance See EN 4604-001. BS EN 4604-003:2009EN 4604-003:2009 (E) 10 6 Designation EXAMPLE Description blockCABLE, COAXIAL Identity blockEN4604-003WZ Number of this st

41、andard Cable code (see TR 6058) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 7 Identification and marking Colour of the marking shall be green or black. See EN 4604-002. 8 Packaging, labelling and delivery length 8.1 Packaging and labelling

42、See EN 4604-001. 8.2 Delivery length The minimum delivery length shall conform to the requirements of the order. 9 Technical specification See EN 4604-001. BS EN 4604-003:2009This page has been intentionally left blank BS EN4604-003:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKT

43、el +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are u

44、pdated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British S

45、tandard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive

46、the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website

47、 http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards

48、 through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administr