BS EN 1876-2-1998 Rubber- or plastics-coated fabrics - Low temperature tests - Impact test on loop《橡胶或塑料涂覆织物 低温试验 环形冲击试验》.pdf

《BS EN 1876-2-1998 Rubber- or plastics-coated fabrics - Low temperature tests - Impact test on loop《橡胶或塑料涂覆织物 低温试验 环形冲击试验》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1876-2-1998 Rubber- or plastics-coated fabrics - Low temperature tests - Impact test on loop《橡胶或塑料涂覆织物 低温试验 环形冲击试验》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1876-2 : 1998 The E

2、uropean Standard EN 1876-2 : 1997 has the status of a British Standard ICS 59.080.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Rubber- or plastics-coated fabrics Low temperature tests Part 2. Impact test on loopThis British Standard, having been prepared under the direct

3、ion of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 March 1998 BSI 1998 ISBN 0 580 29275 4 BS EN 1876-2 : 1998 Amendments issued since publication Amd. No. Date Text affected National foreword This British Standard

4、 is the English language version of EN 1876-2 : 1997. It is an additional method to methods 10A and 10C of BS 3424 : Part 8 : 1983. Method 10B (low temperature bend test) of BS 3424 : Part 8 : 1983 is superseded by BS EN 1876-1. The UK participation in its preparation was entrusted to Technical Comm

5、ittee TCI/78, Coated fabrics, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments

6、 and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue un

7、der the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct appl

8、ication. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committee for Standardization Comi

9、te Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1876-2 : 1997 E EUROPEAN STANDARD EN 1876-2 NORME EUROPE

10、 ENNE EUROPA ISCHE NORM November 1997 ICS 59.080.40 Descriptors: Textiles, coated fabrics, fabrics coated with rubber, fabrics coated with plastics, thermal tests, low temperature tests, thermal shock tests, brittleness, limit temperature of brittleness, bend tests English version Rubber- or plastic

11、s-coated fabrics Low temperature tests Part 2: Impact test on loop Supports textiles reve tus de caoutchouc ou de plastique Essais a basse tempe rature Partie 2: Essai de choc sur boucle Mit Kautschuk oder Kunstoff beschichtete Textilien Pru fungen bei niedrigen Temperaturen Teil 2: Schlaufen-Schlag

12、pru fung This European Standard was approved by CEN on 16 October 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp

13、hical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CE

14、N member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,

15、 Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1876-2 : 1997 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 248, Textiles and textile products, the secretariat of which is held by BSI. This European Standard shall be given the status of a

16、 national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at the latest by May 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count

17、ries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN 1876 deals with low temperature properties of coa

18、ted fabrics and is composed of two parts: Part 1: Bending test Part 2: Impact test on loop Annex A is informative and gives examples of suitable apparatus. NOTE. Persons using this standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safet

19、y problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.Page 3 EN 1876-2 : 1997 BSI 1998 Introduction The determination of the low temperature properties of

20、 rubber or plastic coated fabrics is important for many applications. EN 1876 describes two methods: a method by bending that constitutes part 1, and a method that deals with an impact on the material in a loop, and which constitutes part 2. The cold crack temperature is not a sharply defined temper

21、ature. This temperature depends on the stressed state of the fabric and also the rate of any impact on the loop. This method permits the determination of the temperature limit of brittleness. The method to be employed should be chosen by those concerned in order to ensure it matches as closely as po

22、ssible the conditions likely in use. The results of these two methods are not equivalent and therefore should not be compared. 1 Scope This European Standard specifies a method for the determination of low temperature properties of coated fabrics. This method is only considered suitable for material

23、s which can, at room temperature, be easily bent into the configuration required by the test without damage to the specimen, determined by a test carried out at room temperature. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publicati

24、ons. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. F

25、or undated references the latest edition of the publication referred to applies. EN ISO 2231 Rubber or plastics coated fabrics Standard atmospheres for conditioning and testing EN 22286 Rubber or plastics coated fabrics Determination of roll characteristics 3 Definition For the purposes of this stan

26、dard, the following definition applies: 3.1 temperature limit of brittleness Lowest temperature at which at most one specimen in 20 breaks under the conditions of the test. 4 Principle Rectangular test specimens, bent in the form of a loop and placed in a low temperature chamber, are quickly folded

27、by means of an impact caused by a freely falling hammer. Tests are continued at decreasing temperatures from a multiple of 5 by steps of 5 C until more than one break is observed. 5 Sampling From each laboratory sample, two sets of test specimens shall be cut, one set in the longitudinal direction a

28、nd the other set in the transverse direction. The test specimens shall be selected within the full length of the coated fabric and its usable width, as defined in EN 22286. The test specimens shall be (15 0,5) mm wide and (60 1) mm long. For each test temperature, at least 10 test specimens shall be

29、 tested (five being in the longitudinal direction and five in the transverse direction). 6 Apparatus 6.1 Impact apparatus, having the following general characteristics: a test specimen holder permitting clamping of one or several test specimens over the whole width; an anvil capable of being attache

30、d to the specimen holder and withstanding impact without deformation during the test. The anvil and the test specimen holder shall be level; a hammer of mass (200 2) g made of a vertical axis cylinder, its diameter being between 17 mm and 30 mm. The base of the cylinder shall be chamfered to an angl

31、e of (45 1)8; the chamfered edge being (1 0,1) mm high; a centering system for the hammer equipped with a holding down system to permit a free fall of the hammer from a height of (200 2) mm. Two examples of suitable impact apparatus are given in annex A. 6.2 Cold chamber, containing the impact appar

32、atus, which shall permit a decrease of temperature by steps of 58C. The temperature of the chamber shall be stabilized to 1 8C adjacent to the test specimen. 6.3 Lens, with a magnification of34t o3 6. 7 Atmospheres for conditioning The atmospheres for conditioning shall be as specified in EN ISO 223

33、1. NOTE. The samples should be conditioned for at least 24 h in a free state.Page 4 EN 1876-2 : 1997 BSI 1998 1 Base fabric 2 Intermediate layer 3 Upper layer Figure 1. Chap Figure 2. Fissure Figure 3. Crack 8 Procedure Bend the ends of test specimen to form a loop and clamp on the test specimen hol

34、der. Introduce the test specimen holder into the cold chamber (see 6.2). After (120 15) min, when the test specimens are in equilibrium with the test temperature, drop the hammer (see 6.1) onto the test specimens. Take the test specimens out of the cold chamber and examine them with the lens (see 6.

35、3). A test specimen is considered broken when it shows a rupture visible with a lens, induced totally or partially over the thickness of the coating (fissures, cracks), and not a surface deformation such as a white line or a chap. The initial test temperature shall be such that no break occurs. Unle

36、ss otherwise agreed by the parties, it shall be a multiple of 5 C. At any test temperature (t), perform the test as follows: test 10 test specimens and check them for breaks; If two or more breaks occur, then the test is ended and the temperature (t f ) is noted; If one test specimen only breaks, th

37、en re-test a new set of 10 specimens. If one or more breaks of this new set occur, then the test is ended and the temperature (t f ) is noted; otherwise, lower the temperature of the chamber by 5 C . Resume the test at this new temperature(t); If no break occurs, then lower the temperature of the ch

38、amber by 5 C. Resume the test at this new temperature as (t). 9 Expression of results The temperature limit of brittleness (t b ) is expressed by t b = t f +5 where t f is the temperature noted at the end of the test; t b and t f are expressed in C. 10 Test report The test report shall include the f

39、ollowing particulars: a) reference to this standard; b) date of test; c) identification of sample and sampling procedure, if required; d) the temperature limit of brittleness specified in clause 9 and the type of damage observed on the sample; e) any deviation from the procedure. NOTE. Coated fabric

40、s are generally anisotropic materials and frequently this test is ended because of breaking of the test specimens in one direction only, either longitudinal or transverse. In this case, it is recommended to indicate this direction in the test report.Page 5 EN 1876-2 : 1997 BSI 1998 1 Hammer 2 Center

41、ing tube 3 Test specimen 4 Grip 5 Specimen holder Figure A.1 Impact apparatus, with a series of several centering tubes assembled Annex A (informative) Examples of impact apparatusPage 6 EN 1876-2 : 1997 BSI 1998 1 Hammer 2 Centering means 3 Support means 4 Grip 5 Test specimen 6 Eight-sided holder

42、Figure A.2 Impact apparatus with eight-sided holderblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

43、 | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British

44、 Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

45、 using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatic

46、ally receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI

47、 implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electro

48、nic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price

49、of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording