BS 6359-1983 Specification for dimensions and position of microfiche heading coating (colour stripe)《缩微平片标题涂层(彩色条)尺寸和位置规范》.pdf

《BS 6359-1983 Specification for dimensions and position of microfiche heading coating (colour stripe)《缩微平片标题涂层(彩色条)尺寸和位置规范》.pdf》由会员分享，可在线阅读，更多相关《BS 6359-1983 Specification for dimensions and position of microfiche heading coating (colour stripe)《缩微平片标题涂层(彩色条)尺寸和位置规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6359:1983 Specification for Dimensions and position of microfiche heading coating (colour stripe) UDC 778.142.072.025.42.068BS6359:1983 This British Standard, having been prepared under the directionof the Documentation Standards Committee, was published under the authority ofthe

2、 Board of BSI and comes intoeffect on 31March1983 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference DOS/16 Draft for comment 81/60543 DC ISBN 0 580 13258 7 Committees responsible for this British Standard This British Standard was published under the d

3、irection of the Documentation Standards Committee DOS/-. Its preparation was entrusted to Technical Committee DOS/16 upon which the following bodies were represented: Aslib Association of Medical Records Officers Association of Photographic Technicians British Airways British Broadcasting Corporatio

4、n British Library (Reference Division) British Micrographic Manufacturers Association British Photographic Association British Telecom Business Equipment Trade Association Drawing Office Material Manufacturers and Dealers Association Electricity Supply Industry in England and Wales Electronic Engine

5、ering Association Engineering Equipment Users Association Greater London Council Her Majestys Stationery Office Industrial Council for Educational and Training Technology Institute of Reprographic Technology Library Association Microform Association of Great Britain Ministry of Defence National Coal

6、 Board National Reprographic Centre for documentation Society of Archivists Society of British Aerospace Companies Amendments issued since publication Amd. No. Date of issue CommentsBS6359:1983 BSI 12-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions

7、1 3 General 1 Appendix A Colour 3 Figure 1 Winding orientation 1 Figure 2 Position of heading coating 2 Table 1 Width of heading coating plus edge margin (seeFigure 2) 1 Publications referred to Inside back coverBS6359:1983 ii BSI 12-1999 Foreword This British Standard has been prepared under the di

8、rection of the Documentation Standards Committee. The use of a heading coating (colour stripe) for microfiche headings, particularly for duplicates, has developed in recent years and is now widespread. This British Standard is published to minimize the proliferation of sizes and thus to simplify the

9、 requirements for both manufacturer and user. In the production of microfiche the general practice is to apply the heading coating to the film while it is in roll form. Film in roll form is also often used in duplicators. The requirements therefore apply to roll film from which microfiche will be ma

10、de as well as to microfiche in sheet form. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations

11、. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the insi

12、de front cover.BS6359:1983 BSI 12-1999 1 1 Scope This British Standard specifies requirements for the nominal width, position and thickness of heading coating for microfiche for general, but not archival, use. It applies to all types of film (diazo, silver and vesicular) used in the production of su

13、ch microfiche, whether in roll or sheet form. Suitable colours for use with the different types of film are given inAppendix A. NOTEThe titles of the publications referred to in this standard are listed on theinside back cover. 2 Definitions For the purposes of this British Standard the following de

14、finitions apply. 2.1 heading area the space reserved for eye-legible information above the image area of a microfiche 2.2 heading coating (colour stripe) a backing, which may be translucent or opaque, white or coloured (seeAppendix A), applied to the heading area of an unprocessed microfiche to impr

15、ove legibility and to provide a visual classification of the processed microfiche 2.3 winding a heading coating applied to the edge of the outer side of a roll of film NOTEIf the heading coating is applied to the left-hand edge of the roll when viewed as shown inFigure 1(a), it is known as winding A

16、. If the coating is applied to the right-hand edge of the roll when viewed as shown inFigure 1(b), it is known as windingB. 3 General 3.1 Heading area. The dimensions of the heading area shall comply with one of the formats specified in BS4187-1, BS4187-3, BS5644 or BS5956. The heading coating shall

17、 be applied to the film in the heading area. 3.2 Roll film. Roll film shall be wound with the emulsion (sensitized) side on the inner side, i.e.towards the core, and the heading coating shall be applied to the outer, non-emulsion (non-sensitized) side of the film, not more than1mm from the edge usin

18、g winding A or winding B (seeFigure 2). 3.3 Microfiche. The heading coating shall be applied to the non-emulsion (non-sensitized) side of the cut microfiche on the long edge that has the corner cut, not more than1mm from the edge. 3.4 Width of heading coating. The width of the heading coating plus t

19、he edge margin shall be as given inTable 1. Table 1 Width of heading coating plus edgemargin (seeFigure 2) 3.5 Thickness. The heading coating shall increase the thickness of the microfiche by not more than0.01mm. Frame format Width of heading coating plus edge margin (W) mm 63, 98 208,325 270, 420 1

20、2.75 0.25 9.25 0.25 6.50 0.25 Figure 1 Winding orientationBS6359:1983 2 BSI 12-1999 Figure 2 Position of heading coatingBS6359:1983 BSI 12-1999 3 Appendix A Colour If colours are used for heading coatings, they should not impair the legibility of the heading. Light, bright colours, such as white, ye

21、llow and red, are suitable for use with diazo and silver films. Dark colours, such as black, dark green and dark blue, are suitable for use with vesicular films.4 blankBS6359:1983 BSI 12-1999 Publications referred to BS 4187, Microfiche. BS 4187-1, Specification for formats of60 and98 frames. BS 418

22、7-3, Formats of208,270,325 and420 frames (except COM). BS 5644, Specification for computer output microfiche (COM), A6 size. BS 5956, Specification for A6-size microfiche for the motor industry. BS 6359:1983 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independe

23、nt national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they posse

24、ss the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity

25、of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign stand

26、ards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standar

27、ds BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information C

28、entre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyr

29、ight Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted i

30、n any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.