BS 5815-2-1988 Sheets sheeting pillowslips towels napkins counterpanes and continental quilt secondary covers suitable for use in the public sector - Specification for towels and n.pdf

《BS 5815-2-1988 Sheets sheeting pillowslips towels napkins counterpanes and continental quilt secondary covers suitable for use in the public sector - Specification for towels and n.pdf》由会员分享，可在线阅读，更多相关《BS 5815-2-1988 Sheets sheeting pillowslips towels napkins counterpanes and continental quilt secondary covers suitable for use in the public sector - Specification for towels and n.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS5815-2: 1988 Incorporating Amendment No.1 Sheets, sheeting, pillowslips, towels, napkins, counterpanes and continental quilt secondary covers suitable for use in the public sector Part2: Specification for towels and napkins UDC677.01:645.48BS5815-2:1988 This British Standard, havi

2、ng been prepared under the directionof the Textiles and Clothing Standards Committee, was published under the authorityof the Board of BSI andcomes into effect on 29 January 1988 BSI03-1999 First published as BS5815, December 1979 First Part revision, Part2, January 1988 The following BSI references

3、 relate to the work on this standard: Committee reference TCM/2 Draft for comment85/44139 DC ISBN 0 580 15832 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Textiles and Clothing Standards Committee (TCM/-) to Technical Committee TCM/

4、2, upon which the following bodies were represented: British Railways Board Department of Health and Social Security Department of the Environment, the Crown Suppliers Flax and Linen Association (GB) Household Textiles Association Man-made Fibres Producers Committee Ministry of Defence Textile Resea

5、rch Council Amendments issued since publication Amd. No. Date of issue Comments 8677 September 1995 Indicated by a sideline in the marginBS5815-2:1988 BSI 03-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Fabric 1 4 Towels 1 5 Napkins 3 Appendi

6、x A Information to be supplied by the purchaser 4 Appendix B Item reference cross references 4 Appendix C Determination of terry ratio 4 Table 1 Construction and performance requirements of fabric 2 Table 2 Dimensions and mass of towels and napkins 3 Table 3 Cross references of item references in BS

7、5815-2:1988 and in BS5815:1979 4 Publications referred to Inside back coverBS5815-2:1988 ii BSI 03-1999 Foreword This Part of BS5815 has been prepared under the direction of the Textiles and Clothing Standards Committee and forms a part revision of BS5815:1979 which will be withdrawn on publication

8、of all three Parts. This revision includes additional products and is being published in three Parts as follows: Part1: Specification for sheeting, sheets and pillowslips 1) ; Part2: Specification for towels and napkins; Part3: Specification for counterpanes 1) . In this Part, which specifies the re

9、quirements for towels and napkins, the principal changes from the previous edition are: a) the addition of a second range of towels, identified by the reference TC which describes a range of towels of somewhat different construction from the original T series and which is sold in loomstate; b) a sli

10、ght change in T series towel dimensions to permit more efficient use of modern looms and with the object of improving production efficiency to the benefit of both producers and purchaser; c) the addition of a smaller size of babies terry napkin to accord with the growing use of this size in NHS hosp

11、itals. BS5815 covers only the basic description of the products and their construction and performance requirements. Purchasing authorities therefore may need to include additional information. This Part of BS5815 covers the end products quoted but can also be used to specify the fabric from which t

12、hey are manufactured. Many properties cannot be specified objectively and cannot therefore be included in this standard. Examples of such properties include colour, handle, appearance and details of additional design features. Public sector purchasing authorities may be able to supply standard patte

13、rns which cover these properties and serve to resolve any ambiguities of description. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of it

14、self confer immunity from legal obligations. In particular, attention is drawn to Statutory Instrument 1986 No.26, the Textile Products (Indications of Fibre Content) Regulations 1986. Summary of pages This document comprises a front cover, an inside front cover, pagesi and ii, pages1 to4, an inside

15、 back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover. 1) In preparationBS5815-2:1988 BSI 03-1999 1 1 Scope This Part of BS5815 specifies the requirements for

16、the materials, manufacture, make-up and testing of terry towels and babies terry napkins. The dimensions of these articles are also specified. Information to be supplied by the purchaser is given in Appendix A Appendix B includes a table giving cross references between item references in this revisi

17、on (BS5815-2:1987) and in BS5815:1979, as well as Ministry of Defence (MOD) descriptions, pattern numbers and NATO stock numbers, where applicable. NOTEThe titles of the publications referred to in this standard are listed on page5. 2 Definitions For the purposes of this Part of BS5815 the definitio

18、ns given in BS5523 and BS6189 together with the following apply. 2.1 tubular fibre a fibre having a continuous hole along its longitudinal axis 2.2 towel heading the plain (not terry) portion of the towel including the end hems. The heading may be continuous from the hem to the main body of the towe

19、l or may include a bar of terry as a decorative element NOTEThe dimensions of the headings quoted in this Part of BS5815 exclude any such terry elements. 3 Fabric 3.1 The fabric used shall be either of the following: a) all cotton, or b) one in which the pile is composed of a minimum of50%cotton ble

20、nded in an intimate mixture with tubular viscose (the proportion of each fibre in the pile being determined by the method described in BS4407) and in which the base yarns are all cotton. 3.2 The T fabric shall be woven in3 pick terry, the warp being laid in1 ground,1 terry or2 ground,2 terry. The TC

21、 fabric shall be woven in3 pick terry, the warp being laid in2 ground,1 terry. NOTEThe fabric should be uniformly woven from evenly spun yarn. 3.3 The construction and performance requirements of the fabric shall be as given in Table 1, when determined by the respective methods specified in that tab

22、le. 4 Towels 4.1 Fabric Towels shall be made from fabric complying with clause3. 4.2 Heading Headings shall be in plain weave and the maximum depth of the heading at each end of the towel shall be as given in Table 2. 4.3 Sewing thread The sewing thread shall be either: a) core spun polyester and co

23、tton with polyester core and cotton sheath, ticket no.75 complying with Table3 of BS6157:1981, or b) soft, machine, cotton thread,40/3, of linear density43 tex 5% (when measured in accordance with BS2010) with Z twist and of minimum breaking strength9.8N (when measured in accordance with BS1932-1, u

24、sing a constant rate of extension machine). The thread shall be of the same colour as the towel and, in the case of coloured towels, of the same colour fastness. 4.4 End hems The end hems shall be a minimum of2cm wide of hem type6-03-01 as described in BS3870-2. At least1 cm of raw edge shall be tur

25、ned in. 4.5 Side edges The side edges shall be either selvedges, which shall be firm and straight, or hems which shall be of type6-03-01 of BS3870-2 and of minimum width0.6cm. 4.6 Sewing Heading hems shall be sewn using stitch type301 of BS3870-1 and with a minimum of3 stitches per centimetre. Side

26、hems shall be sewn using stitch type101 of BS3870-1 and with a minimum of2.4 stitches per centimetre. 4.7 Colour and finish Towels T2 to T5 and napkins NS1 and NS2 shall be delivered in the finished state, towels TC1 to TC5 in loomstate. 4.8 Dimensions The finished dimensions shall be as specified i

27、n Table 2 when determined by the methods of test in BS1930 and BS1931.BS 5815-2:1988 2 BSI 03-1999 Table 1 Construction and performance requirements of fabric Fabric reference Threads per centimetre min. Terry ratio min. Filling max. Breaking strength min. Cuprammonium fluidity max. Colour fastness

28、of dyed towelling to washing Colour fastness to bleaching: peroxide Colour fastness ato washing in the presence of sodium hypochlorite Maximum change in colour Warp (pile and ground) Weft Warp Weft Maximum change in colour Maximum change in colour % N N units T2,T3,T4,T5 22 16.5 6:1 Nil 310 356 6 4-

29、5 4-5 4-5 TC1,TC2,TC 3, TC4,TC5 24 15.5 3.33:1 3.5 475 400 6 4-5 4-5 NS1,NS2 22 14.2 4.5:1 Nil 310 310 6 4-5 Method of test BS2862 Appendix C BS4032 BS2576 BS2610 BS1006, sectionCO4 BS1006, sectionNO2 BSEN 20105-C06, Test No.D3M a Requirement for MOD; dyed towels only.BS5815-2:1988 BSI 03-1999 3 Tab

30、le 2 Dimensions and mass of towels and napkins 5 Napkins 5.1 Fabric Napkins shall be made from fabric T complying with clause3. 5.2 Sewing thread The sewing thread shall be either: a) core spun polyester and cotton with polyester core and cotton sheath, ticket no.75 complying with Table3 of BS6157:1

31、981, or b) soft, machine, cotton thread,40/3, of linear density43 tex 5% (when measured in accordance with BS2010) with Z twist and of minimum breaking strength9.8N (when measured in accordance with BS1932-1, using a constant rate of extension machine). 5.3 Edges The edges shall be secured by selved

32、ge, hemming or overlocking. The hems shall be type6-03-01 of BS3870-2. 5.4 Sewing For end hems stitch type301 as described in BS3870-1 shall be used and there shall be not less than3 stitches per centimetre. For side hems stitch type101 of BS3870-2 shall be used and there shall be not less than2.4 s

33、titches per centimetre. Overlocking shall be of the safety overlock type using stitch type512 of BS3870-1. NOTEThe sewing should be of even tension and the ends finished securely. 5.5 Dimensions The finished dimensions shall be as specified in Table 2 when determined by the methods described in BS19

34、30 and BS1931. Reference Dimensions Heading depth Mass per twelve units Width Length max. min. min. min. cm cm cm kg Towel T2 48 100 12.0 2.08 T3 60 120 13.0 3.11 T4 68 125 14.5 3.67 T5 90 150 15.2 5.84 Towel TC1 48 100 13.0 2.34 TC2 60 120 13.0 3.50 TC3 68 135 13.0 4.47 TC4 75 135 13.0 4.92 TC5 90

35、150 13.0 6.57 Napkin NS1 50 50 No 0.99 NS2 57 60 requirement 1.36 Method of test BS1930 BS1931 BS1931 a a Except that the measurement is taken from the edge of the main terry portion of the towel to the outer edge of the end hem.BS5815-2:1988 4 BSI 03-1999 Appendix A Information to be supplied by th

36、e purchaser The following information should be supplied by the purchaser: a) article type, fibre content, dimensions and reference; b) colour and any special finishing requirements; c) details of any marking or additional design elements; d) packaging instructions; e) instructions for sampling, tes

37、ting and inspection; f) details of any additional requirements. Appendix B Item reference cross references Table 3 contains cross-reference information between the item references used in this Part of BS5815 and those used in the1979 edition of BS5815 as well as MOD descriptions, pattern numbers and

38、 NATO stock numbers, where applicable. Appendix C Determination of terry ratio Cut out a10cm 10cm specimen from the fabric and condition the specimen in the standard temperate atmosphere for testing as defined in BS1051. Remove warp threads from the specimen so as to provide10 threads each from the

39、specimen of ground warp and of terry warp. Determine the mean straightened length of each group of10 threads in accordance with BS2863. Express the terry ratio as the ratio of the mean straightened length of the terry warp threads to the mean straightened length of the ground warp threads. Table 3 C

40、ross references of item references in BS5815-2:1988 and in BS5815:1979 Item Reference in BS5815-2:1988 Previous reference in BS5815:1979 Towel T2 a T2 T3 ab T3 T4 a T4 T5 a T5 Towel TC1 TC2 TC3 TC4 TC5 Napkin NS1 NS2 NS a T series towel dimensions have been changed slightly from the previous specifi

41、cation. b For MOD requirements towel T3 is designated “Towel, hand, terry, cotton, olive drab, pattern no.T957A, NATO Stock No.7210-99-942-2281” or “Towel, hand, terry, cotton, white, pattern no.T342A, NATO Stock No.7210-99-942-2279”.BS5815-2:1988 BSI 03-1999 Publications referred to BS1006, Methods

42、 of test for colour fastness of textiles and leather. BS1051, Glossary of terms relating to the conditioning, testing and mass determination of textiles. BS1930, Method for the determination of width of woven or knitted fabrics when relaxed at zero tension. BS1931, Method for the determination of le

43、ngth of woven or knitted fabrics when relaxed at zero tension. BS1932, Methods of testing the strength of yarns from packages. BS1932-1, Determination of breaking strength and extension. BS2010, Method for the determination of the linear density of yarns from packages. BS2576, Determination of break

44、ing strength and elongation (strip method) of woven fabrics. BS2610, Method of test for the determination of the cuprammonium fluidity of cotton and certain cellulosic man-made fibres. BS2862, Methods for determination of number of threads per unit length. BS2863, Method for determination of crimp o

45、f yarn in fabric. BS3870, Stitches and seams. BS3870-1, Classification and terminology of stitch types. BS3870-2, Classification and terminology of seam type. BS4032, The determination of certain water- or alkali-soluble additives in cellulosic or synthetic fibres, yarns and fabrics or yarns and fab

46、rics made from blends of such fibres. BS4407, Methods of test. Quantitative analysis of fibre mixtures. BS5523, Glossary of terms for textiles Weaves definitions of general terms and basic weaves. BS6157, Specification for industrial sewing threads made wholly or partly from synthetic fibres. BS6189

47、, Glossary of terms relating to fabrics and associated fibres, yarns and processes. BSEN20105-C06, Colour fastness to domestic and commercial laundering. BS5815-2: 1988 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for prepar

48、ing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. I

49、t is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI,